Refine Your Search

Topic

Search Results

Standard

Steel, Corrosion-Resistant, Sheet and Strip 19Cr - 9.2Ni (SAE 30304) Cold Rolled, 3/4 Hard, 175 ksi (1207 MPa) Tensile Strength

2019-09-24
WIP
AMS5912C
This specification covers a corrosion-resistant steel in the form of sheet and strip. These products have been used typically for applications requiring moderate forming and bending, but usage is not limited to such applications. Mechanical properties specified herein are obtained by cold working (strain hardening), and not by heat treatment. Therefore, the cold-worked product should not be heated to a temperature which adversely affects the mechanical properties or corrosion-resistance before, during, or after fabrication.
Standard

Steel, Corrosion-Resistant, Sheet and Strip 19Cr - 9.2Ni (SAE 30304) Cold Rolled, Full Hard, 185 ksi (1276 MPa) Tensile Strength

2019-09-24
WIP
AMS5913C
This specification covers a corrosion-resistant steel in the form of sheet and strip. These products have been used typically for applications requiring moderate drawing and forming, but usage is not limited to such applications. Mechanical properties specified herein are obtained by cold working (strain hardening) and not by heat treatment. Therefore, the cold-worked product should not be heated to a temperature which adversely affects the mechanical properties or corrosion-resistance before, during, or after fabrication.
Standard

Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni Cold Rolled, 150 Ksi (1034 MPa) Tensile Strength

2019-09-23
WIP
AMS5518N
This specification covers a corrosion-resistant steel in the form of sheet and strip. These products have been used typically for parts requiring strength and moderate forming or bending, but usage is not limited to such applications. Mechanical properties specified herein are obtained by cold working (strain hardening) and not by heat treatment. Therefore, the cold-worked product should not be heated to a temperature which adversely affects the mechanical properties or corrosion resistance before, during, or after fabrication.
Standard

Calculation of Electron Vacancy Number in Superalloys

2019-07-24
CURRENT
AS5491D
This SAE Aerospace Standard (AS) establishes a uniform procedure for calculation of electron vacancy numbers in superalloys. It is intended for use by suppliers of raw materials and parts, typically castings, for which control of electron vacancy number is required by the raw material specification.
Standard

Heat Treatment of Parts in a Vacuum

2019-07-12
CURRENT
AMS2769C
This specification establishes the requirements and procedures for heat treating parts in vacuum/partial pressure and shall be used as a supplementary document to primary heat treating specifications as applicable.
Standard

Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire

2019-05-10
CURRENT
AMS2261L
This specification covers established manufacturing tolerances applicable to bars, rods, and wire of nickel, nickel alloy, and cobalt alloys ordered to inch-pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of a specified range.
Standard

Elevated Temperature Tensile Properties of Castings

2019-04-15
CURRENT
AMS2361E
This specification establishes a procedure for designating minimum elevated temperature tensile property requirements of castings by means of this AMS number and a series of dash numbers.
Standard

Stress-Rupture Properties of Castings

2019-04-15
CURRENT
AMS2362D
This specification establishes a procedure for designating minimum stress-rupture property requirements of castings by means of this AMS number and a series of dash numbers.
Standard

Room Temperature Tensile Properties of Castings

2019-04-15
CURRENT
AMS2360E
This specification establishes a procedure for designating minimum room temperature tensile property requirements of castings by means of this AMS number and a series of dash numbers.
Standard

Tungsten Carbide-Cobalt Powder, Cast and Crushed

2019-03-28
WIP
AMS7879G
This specification covers tungsten carbide-cobalt in the form of powder. This powder has been used typically for producing plasma spray coatings to provide wear and fretting resistant surfaces, but usage is not limited to such applications.
Standard

Nickel Wire and Ribbon 99Ni

2019-01-07
CURRENT
AMS5555F
This specification covers a nickel in the form of round wire and rectangular ribbon.
Standard

Tolerances, Corrosion and Heat-Resistant Steel Tubing

2018-09-25
WIP
AMS2243L
This specification covers manufacturing tolerances applicable to seamless and welded tubing of corrosion and heat-resistant steel ordered to inch dimensions. These tolerances apply to all conditions and are based on individual measurements, unless otherwise noted. Tubing may be specified by two dimensions only (OD and wall thickness, ID and wall thickness, or OD and ID).
X