Refine Your Search

Date

Date

Topic

Topic

AMS K Non Destructive Methods and Processes Committee Logistics Lubricants Fuels and Energy Sources Identification numbers

Search Results

Viewing 1 to 20 of 138
123Next >Last >>
Sort by published
Standard

Magnetic Particles, Nonfluorescent Dry Method
2023-05-10
CURRENT
AMS3040E
This specification covers nonfluorescent, magnetic particles having black, red, gray, or other color, as specified, supplied in the form of dry powders.
Standard

Ultrasonic Inspection Thin Wall Metal Tubing
2022-06-20
CURRENT
AMS2634C
This specification covers procedures for ultrasonic inspection of thin wall metal tubing of titanium, titanium alloy, and corrosion- and heat-resistant steels and alloys having nominal OD over 0.1875 inch (4.762 mm) with OD to wall thickness ratio of 8 or greater and wall thickness variation not exceeding ±10% of nominal.
Standard

Inspection, Ultrasonic Product Over 0.5 Inch (12.7 mm) Thick
2021-11-09
CURRENT
AMS2630E
This specification covers procedures for ultrasonic inspection, by pulse-echo procedures, of flat, rectangular, round, cylindrical, and contoured products having a thickness or cross-sectional dimension greater than 0.5 inch (12.7 mm), using either contact or immersion methods, and using the longitudinal-wave or shear-wave modes or combinations of the two, as necessary. This specification may apply to testing finished machined parts provided the parts can meet the basic testability requirements, such as size, contour, metallurgical structure, and thickness.
Standard

Eddy Current Inspection of Circular Holes in Nonferrous Metallic Aircraft Engine Hardware
2019-10-14
CURRENT
AS4787A
This SAE Aerospace Standard (AS) establishes minimum requirements for eddy current inspection of circular holes in nonferrous, metallic, low conductivity (less than 5% IACS) aircraft engine hardware with fasteners removed. The inspection is intended to be performed at maintenance and overhaul facilities on engine run hardware.
Standard

Exposure Levels of UV Radiation in Nondestructive Inspection Processes
2019-08-05
CURRENT
AIR4964
Long wave ultraviolet or UV-A radiation (between 320 to 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. The UV-A radiation is obtained from either fluorescent or high intensity discharge lamps that are stationary or portable. The commercially available UV-A lamps possess a large variation in intensity output that can cause a legitimate concern for possible health hazard. This draft reviews the nature of UV-A radiation emitted by these lights, blacklight equipment, acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH) and the European Standards Committee for Nondestructive Testing, and recommendation of proper practices when working with UV-A radiation.
Standard

Ultrasonic Inspection Thin Wall Metal Tubing
2019-04-24
HISTORICAL
AMS2634B
This specification covers procedures for ultrasonic inspection of thin wall metal tubing of titanium, titanium alloy, and corrosion and heat resistant steels and alloys having nominal OD over 0.1875 inch (4.762 mm) with OD to wall thickness ratio of 8 or greater and wall thickness variation not exceeding ±10% of nominal.
Standard

Magnetic Particles, Nonfluorescent Dry Method
2018-09-21
HISTORICAL
AMS3040D
This specification covers nonfluorescent, magnetic particles having black, red, gray, or other color, as specified, supplied in the form of dry powders.
Standard

Ultrasonic Thickness Testing
2018-09-21
HISTORICAL
ARP2654
To provide general instructions for accomplishing ultrasonic thickness measurements. Measurements can be made from one side of a material when access to the opposite side is restricted.
Standard

Magnetic Particles, Nonfluorescent Wet Method, Dry Powder
2018-08-31
HISTORICAL
AMS3042F
This specification covers nonfluorescent, magnetic particles in the form of dry powders intended to be suspended in oil or conditioned water vehicle for use in the wet method, magnetic particle inspection.
123Next >Last >>
X