Refine Your Search

Search Results

Viewing 1 to 7 of 7
Standard

Hydrodynamic Drive Test Code

2018-12-05
CURRENT
J643_201812
The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a Torque ratio versus speed ratio and output speed b Input speed versus speed ratio and output speed c Efficiency versus speed ratio and output speed d Capacity factor versus speed ratio and output speed e Input torque versus input speed NOTE: For more information about these characteristics and the design of hydrodynamic drives, refer to “Design Practices: Passenger Car Automatic Transmissions,” SAE Advances in Engineering, AE-18 (Third Ed.) or AE-29 (Fourth Ed.).
Standard

Passenger Car and Light Truck Automatic Transmission and Automatic Transaxle Test Code

2015-06-30
CURRENT
J651_201506
The extent of test conditions on the dynamometer must be sufficient to determine the efficiency characteristics corresponding to the following range of vehicle operations in all gear ratios with locked torque converters (open converter can also be done where appropriate and noted). a Efficiency versus output speed versus input torque b Torque ratio versus output speed c Input speed versus output speed d Output torque versus output speed e Parasitic loss versus input speed (spin losses) f Cooler flow g Output torque bias (front wheel drive transaxles)
Standard

Hydrodynamic Drive Test Code

2011-04-04
HISTORICAL
J643_201104
The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a Torque ratio versus speed ratio and output speed b Input speed versus speed ratio and output speed c Efficiency versus speed ratio and output speed d Capacity factor versus speed ratio and output speed e Input torque versus input speed NOTE: For more information about these characteristics and the design of hydrodynamic drives, see “Design Practices—Passenger Car Automatic Transmissions,” SAE Advances in Engineering, AE18 or AE29
Standard

Passenger Car and Light Truck Automatic Transmission and Automatic Transaxle Test Code

2005-06-22
HISTORICAL
J651_200506
To provide a means of obtaining the performance characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing. However, by its very nature a transmission should be viewed as a compilation of three major component systems: pump, torque converter, and gearbox (all ratio change elements).
Standard

Passenger Car and Light Truck Automatic Transmission and Automatic Transaxle Test Code

1996-01-01
HISTORICAL
J651_199601
To provide a means of obtaining the performance characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing. However, by its very nature a transmission should be viewed as a compilation of three major component systems: pump, torque converter, and gearbox (all ratio change elements).
Standard

Passenger Car and Light Truck Automatic Transmission and Automatic Transaxle Test Code

1991-01-23
HISTORICAL
J651_199101
To provide a means of obtaining the performance characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing. However, by its very nature a transmission should be viewed as a compilation of three major component systems: pump, torque converter, and gearbox (all ratio change elements).
Standard

Passenger Car and Light Truck Automatic Transmission and Automatic Transaxle Test Code

1979-06-01
HISTORICAL
J651C_197906
To provide a means of obtaining the performance characteristics of automatic transmissions and automatic transaxles. It outlines dynamometer tests that map the steady-state characteristics over a range of operations of an automatic transmission/automatic transaxle and provides a method of presenting test data. This procedure must be followed, with similar test facilities so that results obtained from different laboratories are comparable. For this SAE Recommended Practice, the transmission is defined as the complete automatic transmission or transaxle assembly between the engine and the driveshaft(s) used to effect a ratio change in transmitting power. This test procedure deals with the aspect of conducting complete transmission and transaxle assembly testing. However, by its very nature a transmission should be viewed as a compilation of three major component systems: pump, torque converter, and gearbox (all ratio change elements).
X