Search Results

Seat strength has increased over the past four decades which includes a transition to dual recliners. There are seat collision performance issues with stiff ABTS and very strong seats in rear impacts with different occupant sizes, seating positions and physical conditions. In this study, eight rear sled tests were conducted in four series: 1) ABTS in a 56 km/h (35 mph) test with a 50th Hybrid III ATD at MGA, 2) dual-recliner ABTS and F-150 in a 56 km/h (35 mph) test with a 5th female Hybrid III ATD at Ford, 3) dual-recliner ABTS in a 48 km/h (30 mph) test with a 95th Hybrid III ATD leaning inboard at CAPE and 4) dual-recliner ABTS and Escape in 40 km/h (25 mph) in-position and out-of-position tests with a 50th Hybrid III ATD at Ford. The sled tests showed that single-recliner ABTS seats twist in severe rear impacts with the pivot side deformed more rearward than the stanchion side.

Seats have become stronger over the past two decades and remain more upright in rear impacts. While head restraints are higher and more forward providing support for the head and neck, serious-to-fatal injuries to the thoracic and cervical spine have been seen in occupants with spinal disorders, such as DISH (diffuse idiopathic skeletal hyperostosis), ankylosis, spondylosis and/or osteophytes that ossify the joints in the spine. This case study addresses the influence of spinal disorders on fracture-dislocation and spinal cord injury in rear impacts with relatively upright seats. Nineteen field accidents were investigated where serious-to-fatal injuries of the thoracic and cervical spine occurred with the seat remaining upright or slightly reclined. The occupants were lap-shoulder belted, some with belt pretensioning and cinching latch plate.

Objective: This study involved a number of different tests addressing theories for recliner and track release of front seats in rear impacts. It addresses the validity of the theories. Method: Several separate test series were conducted to address claims made about recliner and track release of front seats in rear impacts. The following theories were evaluated to see the validity of the issues: 1 Recliner teeth slipping with minimal damage to the teeth 2 Recliner teeth bypass by disengaging and re-engaging under load without damaging the teeth 3 Recliner shaft bending and torque releasing the recliners 4 Track release by heel loading 5 Track release with occupant load on the seat 6 Recliner handle rotation causing recliner release 7 Double pull body block tests Results: Many of the theories were found to be uncorroborated once actual test data was available to judge the merits of the issue raised. The laboratory tests were set-up to specifically address particular issues.

During the past decade, there has been a steady increase in studies addressing rollover crashes and injuries. Though rollovers are not the most frequent crash type, they are significant with respect to serious injury and interest in rollovers has grown with the introduction of SUVs, vans, and light trucks. A review of Occupant and Vehicle Responses in Rollovers examines relevant conditions for field roll overs, vehicle responses, and occupant kinetics in the vehicle. This book edited by Dr. David C. Viano and Dr. Chantal S. Parenteau includes 62 technical documents covering 15 years of rollover crash safety, including field crash statistics, pre- and rollover dynamics, test procedures and dummy responses.

For several decades, there has been a debate on the safety merits of yielding and rigidized (stiff) seats. In 1995, GM adopted requirements for high retention seats and introduced a new generation of yielding seatbacks. These seats have the same stiffness as the yielding seats of the 1980s and early 1990s, but have a strong frame structure and recliners to substantially limit seatback rotation in severe rear crashes. The yielding behavior is given by compliance of the seat suspension across the side structures and an open perimeter frame, which allows the occupant to penetrate into the seatback. The purpose of this study is to compare the energy transfer characteristics and occupant dynamics of yielding and stiff seats in 35 km/h and 16 km/h rear crashes. Based on benchmarking tests, the stiff seatback is defined as one having a 40 kN/m stiffness in rearward loading by a Hybrid dummy.

This paper reviews issues relating to seats including design for comfort and restraint, mechanics of discomfort and irritability, older occupants, and low-back pain. It focuses on the interface between seating technology and occupant comfort, and involves a technical review of medical-engineering information. The dramatic increase in the number of features currently available on seats outreaches the technical understanding of occupant accommodation and ride comfort. Thus, the current understanding of seat design parameters may not adequately encompass occupant needs. The review has found many pathways between seating features and riding comfort, each of which requires more specific information on the biomechanics of discomfort by pressure distribution, body support, ride vibration, material breathability, and other factors. These inputs stimulate mechanisms of discomfort that need to be quantified in terms of mechanical requirements for seat design and function.

This paper covers the development of the General Motors Energy Absorbing Steering System beginning with the work of the early crash injury pioneers Hugh DeHaven and Colonel John P. Stapp through developments and introduction of the General Motors energy absorbing steering system in 1966. evaluations of crash performance of the system, and further improvement in protective function of the steering assembly. The contributions of GM Research Laboratories are highlighted, including its safety research program. Safety Car, Invertube, the biomechanic projects at Wayne State University, and the thoracic and abdominal tolerance studies that lead to the development of the Viscous Injury Criterion and self-aligning steering wheel.

This paper contains a review of current information on biological structure, material properties and failure characteristics of bone, articular cartilage, ligament and tendon. The load-deformation response of biological tissues is presented with particular reference to the microstructure of the material. Although many of the tissues have been characterized as linear, elastic and isotropic materials, they actually have a more complicated response to load, which includes stiffening with increasing strain, inelastic yield, and strain rate sensitivity. Failure of compact and cancellous bone depends on the rate, type, and direction of loading. Soft biological tissues are vlscoelastie and exhibit a higher load tolerance with an increasing rate of loading. The paper includes a discussion on the basic principles of biomechanics and emphasizes material properties and failure characteristics of biological tissues subjected to impact loading.

Life threatening chest injury can involve partial or full tears of the aorta. Investigations of fatal injuries in automobile accidents indicate that aortic trauma occurs in 10-20% of the cases. The major sites of aortic trauma include the aortic isthmus, the root, and the aortic insertion at the diaphragm - all of which are points of aortic tethering. The biomechanics of the injury process involve stretching of the vessel from points of tethering and hydrodynamic increases in blood pressure, which stretch the tissue to failure at a strain of about 150%. The non-isotropic stretch response of aortic tissue is discussed with reference to the frequent transverse orientation of the laceration. Congenital and pathophysiological conditions also influence the failure characteristics of the tissue. The significant factors associated with traumatic injury of the aorta are discussed in this review paper which is based on published technical information.

Five anesthetized porcine subjects were exposed to blunt thoracic impact using a 21 kg mass with a flat contact surface traveling at 3.0 to 12.2 m/s. The experiments were conducted to assess the appropriateness of studying in vivo mechanical and physiological response to thoracic impact in a porcine animal model. A comprehensive review of comparative anatomy between the pig and man indicates that the cardiovascular, respiratory and thoracic skeletal systems of the pig are anatomically and functionally a good parallel of similar structures in man. Thoracic anthropometry measurements document that the chest of a 50 to 60 kg pig is similar to the 50th percentile adult male human, but is narrower and deeper. Peak applied force and chest deflection are in good agreement between the animal's responses and similar impact severity data on fresh cadavers.