Refine Your Search

Search Results

Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series

2019-08-07
CURRENT
J174_201908
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.
Standard

Metric Thread Rolling Screws

2018-08-20
WIP
J1237
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Tension Indicating Washer Tightening Method for Fasteners

2018-04-24
CURRENT
J2486_201804
This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.
Standard

Metric Thread Rolling Screws

2017-09-07
CURRENT
J1237_201709
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Mechanical and Material Requirements for Steel Nuts

2017-07-20
CURRENT
J995_201707
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
Standard

Nut and Conical Spring Washer Assemblies

2017-05-30
CURRENT
J238_201705
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series

2017-01-03
CURRENT
J174M_201701
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.
Standard

Mechanical and Material Requirements for Wheel Bolts

2016-11-21
CURRENT
J1102_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2016-11-18
CURRENT
J1102M_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Conical Spring Washers

2016-08-31
CURRENT
J773_201608
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2014-05-07
CURRENT
J429_201405
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Nut and Conical Spring Washer Assemblies

2013-04-15
HISTORICAL
J238_201304
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
Standard

Tension Indicating Washer Tightening Method for Fasteners

2013-04-15
HISTORICAL
J2486_201304
This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.
Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2013-04-11
HISTORICAL
J1102M_201304
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Wheel Bolts

2013-04-11
HISTORICAL
J1102_201304
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series

2013-04-11
HISTORICAL
J174M_201304
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series

2013-04-11
HISTORICAL
J174_201304
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.
Standard

Thread Rolling Screws

2012-07-05
CURRENT
J81_201207
This SAE Standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) NOTE—The performance requirements covered in this document apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.
Standard

Mechanical and Material Requirements for Steel Nuts

2012-02-21
HISTORICAL
J995_201202
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 in, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 in, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
X