Search Results

At the 1999 SETC meeting, a paper presented a simple, tuned and silenced exhaust system for a two-stroke engine which theoretically reduced both noise and exhaust emissions and increased engine power and fuel efficiency. In this paper that design concept is applied to a small 56 cc industrial engine and experimentally shown to deliver the projected behaviour which was predicted in that earlier publication. Experimental test results are presented for power output, fuel consumption, and exhaust emissions to illustrate these statements. An accurate engine simulation software package (VIRTUAL 2-STROKE) is employed to model the entire two-stroke engine and to demonstrate not only its effectiveness as a design tool in this area but also that it can accurately predict the above-mentioned performance and emission characteristics.

One-dimensional (1-D) unsteady gas dynamic models of a number of common muffler (or silencer) elements have been incorporated into a1-D simulation code to predict the impact of the muffler on the gas dynamics within the overall system and the radiated Sound Pressure Level (SPL) noise spectrum in free-space. Correlation with measured data has been achieved using a Single-Pulse rig for detailed unsteady gas dynamic analysis and a Rotary-Valve rig in conjunction with an anechoic chamber for noise spectra analysis. The results obtained show good agreement both gas dynamically and acoustically. The incorporation of these models into a full 1-D engine simulation code should facilitate the rapid assessment of various muffler designs prior to prototype manufacture and testing.

This paper reports on the first phase of an experimental evaluation of four different methods for the mathematical modelling of unsteady gas flow in a pipe system containing an area discontinuity. The four methods under investigation are the non-homentropic method of characteristics, the two-step Lax-Wendroff method with flux corrected transport, the Harten-Lax-Leer upstream difference method and the GPB finite system method. The experimentation is conducted using the QUB SP (single-pulse) pressure wave generator consisting of a cylinder, connected via a sliding valve to a long duct. The pressure waves it creates closely mimic those to be found in i.c. engines. The initial cylinder pressure may be set to simulate either an induction or an exhaust process. Various ducts are attached to the pressure wave generator to simulate both sudden and gradual area changes. Each duct is sufficiently long as to permit pressure wave observation without superposition effects.

This paper reports on the experimental evaluation of certain aspects of the mathematical modelling by the GPB method of pressure wave propagation through finite systems, of unsteady gas flow in engine ducting. The aspects under examination are the propagation of pressure waves through a pipe which contains gases of dissimilar properties. In this case the gases are carbon dioxide and air. The experimentation is conducted using the QUB SP (single pulse) pressure wave generator consisting of a cylinder, connected via a sliding valve to a long duct. The pressure waves it creates closely mimic those to be found in i.e. engines. The initial cylinder pressure may be set to simulate either an induction or an exhaust process, but the experiments reported here are of compression waves only. The duct attached to the pressure wave generator is a straight pipe. The cylinder and part of the pipe are filled with carbon dioxide and air.

This paper reports on the first phase of an experimental evaluation of five different methods for the mathematical modelling of unsteady gas flow in engine ducting. The five methods under investigation are the homentropic method of characteristics, the non-homentropic method of characteristics, the two-step Lax-Wendroff method with flux corrected transport, the Harten-Lax-Leer upstream difference method and the Blair method of pressure wave propagation through finite spaces. A single cycle pressure wave generator consisting of a cylinder, connected via a sliding valve to a long duct, has been designed and built. The pressure waves it creates closely mimic those to be found in i.e. engines. The cylinder and the ducts of the device can be filled with any gas and at elevated temperatures. A perfect seal exists between the cylinder and the valve thus enabling mass- flow correlation. The initial cylinder pressure may be set to simulate an induction or an exhaust process.

A 500 cc single cylinder two-stroke engine employing cross scavenging and direct air-assisted gasoline injection is described. Preliminary engine test results are presented for 3000 rpm full load and 1600 rpm part load operating conditions. The effects of fuel injection timing on full and part load brake specific fuel consumption and exhaust emissions are examined.

The emissions produced from a simple carburetted crankcase scavenged two-stroke cycle engine primarily arise due to losses of fresh charge from the exhaust port during the scavenging process. These losses lead to inferior fuel consumption and a negative impact on the environment. Pressure on exhaust emissions and fuel consumption has reduced the number of applications of the two-stroke cycle engine over the years, however the attributes of simplicity, high power density and potential low manufacturing costs have ensured its continuing use for mopeds and motorcycles, small outboard engines and small utility engines. Even these last bastions of the simple two-stroke engine are being challenged by the four stroke alternative as emissions legislation becomes tighter and is newly formulated for many categories of engines. A simple solution is described which reduces short circuit and scavenge losses in a cost effective way.

This paper presents confirmation of the accuracy of prediction of an engine simulation model. The experimental data used to compare with the output of the simulation model are from a single cylinder four-stroke cycle engine and from a single-cylinder two-stroke cycle engine; both engines are naturally aspirated and use spark- ignition. In addition, for the two-stroke cycle engine, the experimental data includes two cylinders with different scavenging characteristics which induce variations of performance characteristics of up to 20%. The fundamentals of the theoretical approach have been presented before to SAE (1)* and this paper extends that theory by providing a detailed discussion on the inclusion of measured scavenging characteristics to enable the simulation model to predict the mechanism of the in-cylinder gas exchange process.

In a previous paper (6)* SAE 850178, the authors pointed out that the single-cycle gas simulation rig which they had developed would prove to be an invaluable experimental tool for the development of two-stroke cycle engine cylinders to attain better scavenging and trapping efficiency of the fresh charge. This paper reports on the use of that now proven experimental technique to examine one of the longest running, and hitherto unresolved, discussions in the field of small two-stroke cycle engines: is loop-scavenging really superior to cross-scavenging? All of the cross-scavenging tests in the paper are compared to tests conducted on loop-scavenged cylinders of the same basic geometry and which were reported previously to SAE. The main conclusion from the experimental investigation is that cross-scavenging is superior to loop-scavenging at low or modest scavenge ratios but is inferior at high scavenge ratios.

A three dimensional computational fluid dynamics program is used to simulate theoretically the scavenging process in the loop-scavenged two-stroke cycle engine. The theoretical calculation uses the k - ε turbulence model and all calculations are confined to the in-cylinder region. The calculation geometry is oriented towards five actual engine cylinders which have been tested under firing conditions for the normal performance characteristics of power, torque, and specific fuel consumption. The same five engine cylinders have also been experimentally tested on a single-cycle gas testing rig for their scavenging efficiency - scavenge ratio characteristics. The ranking of the cylinders in order of merit in terms of scavenging efficiency by both the rig and the theoretical calculations is shown to be in good agreement with the evidence provided by the actual firing engine test results.

This paper presents a single-cycle gas simulation of the scavenging process in a two-stroke cycle engine. The apparatus used is described in the most detailed fashion and the experimental procedure is covered completely. On the apparatus is placed some eleven differing cylinders of a Yamaha 250 motorcycle engine and the scavenging efficiency - scavenge ratio characteristics of each determined experimentally. The results of these experiments are compared with the known performance characteristics of the same eleven cylinders which were obtained under firing conditions for variations of power, torque, air-flow, fuel consumption and scavenging efficiency at several speeds and throttle positions. The correlation, between the ranking of the several cylinders determined on the scavenging simulation apparatus with the performance characteristics obtained under firing conditions, is very good.

This paper describes a unique design of deflector piston for a cross-scavenged two-stroke cycle engine which incorporates the advantages of good scavenging, rapid combustion and reduced thermal loading on the piston. Test results are presented to confirm this statement from two small capacity outboard marine engines and comparisons are made between the experimental test results from the modified and standard power units; of significance is the reduced fuel consumption rate of the modified engines in both cases. A high bmep 400 cm3 single cylinder engine is designed, constructed and tested so as to determine the extent of deflector burning under conditions of high thermal loading. On all three engines the ignition timing for best power is shown to be in the 21-24° btdc region, by comparison with 32-38° btdc conventionally. The spark plug seat temperatures are reduced to 150 C maximum at peak power by comparison with 250-280 °C normally.

This paper describes a unique and uncomplicated method of stratified-charging a two-stroke cycle engine which assists in reducing the short-circuited loss of fuel during scavenging. Performance characteristics as presented were acquired from tests conducted on a 400 cm3 naturally aspirated, single cylinder, spark ignition two-stroke engine with carburettor control of gasoline fuel, the design and construction of the engine also being done at The Queen's University of Belfast. Using a tuned exhaust pipe, the engine produces a peak power of 16 kW at 5000 rev/min and has a minimum brake specific fuel consumption of 0.275 kg/kWh. Moreover, for the tests presented at full and quarter throttle openings, virtually all of the brake specific fuel consumption values are below 0.36 kg/kWh. Most of the performance characteristics shown at various engine speeds are as a function of air/fuel ratio. This paper is a continuation of that presented as SAE 830093.

The paper describes and lists the performance characteristics of a 400 cm3 single-cylinder two-stroke cycle engine with natural-aspiration, spark-ignition and carburetter control of gasoline fuel. The engine features an uncomplicated and unique system of stratified-charging which helps reduce the short-circuited loss of fuel during scavenging. With an untuned exhaust system the engine produces a peak power of 13 kW at 5500 rev/min and a brake specific fuel consumption which has a minimum of 0.265 kg/kWh but, more importantly, virtually the entire speed and load range is below 0.34 kg/kWh (0.55 lb/hp. hr). All performance characteristics at several throttle openings are presented at various engine speeds as a function of air/fuel ratio.

The theoretical modelling of the scavenge process for a naturally aspirated two-cycle engine is described and employed in conjunction with an unsteady gas dynamic analysis of flow in the engine ducting. Programmed for a digital computer, the results of this theoretical study are shown in relation to a 250 cm3 engine with values of predicted charging efficiency, scavenging efficiency, and delivery ratio given as a function of engine speed. These are compared with measured values of scavenging efficiency and the usual performance characteristics of power, mean effective pressure, delivery ratio, and specific fuel consumption. Also compared are the measured and predicted pressure diagrams taken in the cylinder, the crankcase, and the exhaust and inlet ducts. The design of a somewhat unique cylinder gas sampling valve of the mechanical type is described and its usage discussed both theoretically and practically.

Previous papers published by the author have described unsteady gas flow through a naturally aspirated two-cycle engine and the most recent of these publications details a theoretical modelling of the gas exchange or scavenge process for the cylinder of this type of power unit. This results in the ability to predict the trapped charge state, mass, and purity characteristics. With such information it becomes sensible to apply a closed cycle thermodynamic analysis to it and to further predict directly power, torque, and fuel consumption characteristics. This paper describes such a simple closed cycle analysis and compares the theoretical results of power, mean effective pressure, specific fuel consumption, and cylinder pressure diagrams with corresponding measured data from two engines.

From a theoretical analysis of the unsteady efflux from the open end of a simulated reciprocating internal combustion engine exhaust system a prediction of overall and one-third octave sound pressure levels in space, due to this gas flow, is produced. The predictions are compared with measured levels and show a high degree of correlation.

The performance characteristics of a naturally aspirated two-cycle engine can be predicted with an unsteady gas dynamics analysis of flow through the crankcase and cylinder; such an analysis provides values of volumetric efficiency and trapping pressure at any given engine speed. The predictions of the volumetric efficiency and trapping pressure are compared with experimental values from a high-specific-output engine and further amplified with theoretical/experimental comparisons of pressure-time histories taken in the exhaust, transfer, and inlet systems at several engine speeds. The theoretical derivation of unsteady gas dynamic cylinder to pipe boundary conditions is presented so that they become both economical of computer time and mathematically stable.

A computer program has been developed which predicts the sound pressure level and the frequency spectrum produced by simple engine exhaust systems. The program utilizes unsteady flow gas dynamic theory to predict the pressure-time history in the exhaust system and the velocity-time history at the open end of the system. Acoustic theory is then used to predict the sound pressure levels and frequency spectrum in free space. The work was carried out on a twin-cylinder four-cycle engine, but the theory can be applied to any internal combustion engine.

Modern turbocharged diesel engines employ exhaust driven turboblowers operating at high speeds up to 100,000 rpm. The performance assessment of such units demands precise and controllable power absorption and torque measurements at these very high rotational speeds. Additionally the parameters, speed, mass flow, static and dynamic pressures and temperatures must be measured. The turbine power absorption and torque measutement present unique problems. The remaining parameters may present some difficulties but generally the problems are not so great. The design of a high speed dynamometer and the development problems encountered are described. The dynamometer has been used to establihs the performance characteristics of a C. A. V. 01 turbocharger and these are reported.