Search Results

Statistical methods, using the entire time-history, can be used to assess the impact response of an ATD (Anthropomorphic Test Device) in terms of its repeatability and reproducibility. In general, the methods generate a correlation relationship described as shape, magnitude and phase-difference between two time-histories’ in a given set of similar tests: for repeatability the relationship it is for the same ATD, for reproducibility it is for different ATDs of the same design and for biofidelity it is a relationship between ATDs and biomechanical response data from a series of human surrogate impact tests. The method uses the phase relationship to minimize the difference between any two time-histories through an alignment procedure and the magnitude and shape correlations are used to generate a parametric evaluation of the differences between any two time-histories, or set of time-histories.

Two methods of assessing the similarity of a set of impact test signals have been proposed and used in the literature, which are cumulative variance-based and cross correlation-based. In this study, a normalized formulation unites these two approaches by establishing a relationship between the normalized cumulative variance metric (v), an overall similarity metric, and the normalized magnitude similarity metric (m) and shape similarity metric (s): v=1 − m · s. Each of these ranges between 0 and 1 (for the practical case of signals acquired with the same polarity), and they are independent of the physical unit of measurement. Under generally satisfied conditions, the magnitude similarity m is independent of the relative time shifts among the signals in the set; while the shape similarity s is a function of these.

This paper reports a 2010 study undertaken to determine generic acceleration pulses for testing and evaluating advanced batteries for application in electric passenger vehicles. These were based on characterizing vehicle acceleration time histories from standard laboratory vehicle crash tests. Crash tested passenger vehicles in the United States vehicle fleet of the model years 2005-2009 were used. The crash test data were gathered from the following test modes and sources: 1 Frontal rigid flat barrier test at 35 mph (NHTSA NCAP) 2 Frontal 40% offset deformable barrier test at 40 mph (IIHS) 3 Side moving deformable barrier test at 38 mph (NHTSA side NCAP) 4 Side oblique pole test at 20 mph (US FMVSS 214/NHTSA side NCAP) 5 Rear 70% offset moving deformable barrier impact at 50 mph (US FMVSS 301). The accelerometers used were from locations in the vehicle where deformation is minor or non-existent, so that the acceleration represents the “rigid-body” motion of the vehicle.

Ten sled tests were conducted with a Hybrid III 10-year-old dummy under a 3-point belt only restraint condition to evaluate its performance. The results of the Hybrid III 10-year-old in these tests indicate that there are artifactural noise spikes observable in the transducer responses. A number of metal-to-metal contacts in the shoulder area were identified as one of the sources for the chest acceleration spikes. Noise spikes were also observed in the response from multiple body regions; however, the source of the spikes could not be determined. Compared to the other Hybrid III dummies, non-characteristic dummy chest deflection responses were also observed. This limited analysis indicates that the Hybrid III 10-year-old dummy requires additional development work to eliminate the metal-to-metal contacts in the shoulder area and to understand and correct the other sources of the noise spikes. More investigation is needed to determine if the chest deflection response is appropriate.

This paper analyzes the difference in impact response of the forehead of the Hybrid III and THOR-NT dummies in free motion headform tests when a dummy strikes the interior trim of a vehicle. Hybrid III dummy head is currently used in FMVSS201 tests. THOR-NT dummy head has been in development to replace Hybrid III head. The impact response of the forehead of both the Hybrid III dummy and THOR dummy was designed to the same human surrogate data. Therefore, when the forehead of either dummy is impacted with the same initial conditions, the acceleration response and consequently the head Injury criterion (HIC) should be similar. A number of manufacturing variables can affect the impacted interior trim panels. This work evaluates the effect of process variation on the response in the form of Head Injury Criterion (HIC).

Restraint systems play an important role in managing the energy of occupants during a crash event. Belt and airbag systems complement each other in order to gradually decelerate the occupant. However, the seating position of the 5th percentile female and 50th percentile male occupants forces the need to manage this energy in different ways. MADYMO simulation of a generic vehicle-restraint system with a driver side 5th and a 50th percentile Hybrid III dummy were done for a typical frontal impact. The belt system had a retractor/load limiter, but no pretensioner. The effect of airbag fabric porosity, inflation rate and seat belt load limiting ability were evaluated for both occupants. Parameters examined that affect system rebalancing to achieve the highest star rating were HIC and 3ms Chest acceleration.

This technical paper presents the results from tests conducted with the ES-2re, a version of the ES-2 side impact dummy that was modified by the National Highway Traffic Safety Administration (NHTSA) to improve its performance in crash tests. Through the series of biofidelity tests conducted on the ES-2re, described in International Standards Organization (ISO) Technical Report (TR)9790 (1999), the OSRP observed a final overall biofidelity ranking of 4.1 for the ES-2re, which corresponds to an ISO classification of “marginal.” The biofidelity of the ES-2re is compared to that of the ES-2 and the WorldSID. Repeatability was also evaluated on the ES-2re based on the biofidelity test data. Additional pendulum tests were performed to assess the response of the dummy in oblique loading conditions, and results indicate that oblique loading from the front leads to significantly reduced rib deflections.

While the Hybrid III anthropomorphic test device (ATD) family has experienced a lengthy period of development, and is an essential part of vehicle safety regulation, several issues associated with the ATD's head/neck design and the neck dynamic response due to airbag loading have been identified. As a result, the response of the Hybrid III neck under a number of airbag loading conditions could be an “artifact” of the ATD and not representative of the live human. One area of concern relates to the method of incorporating the human neck muscles into the neck response and how this affects the out-of-position (OOP) tests mandated in the new FMVSS 208. The results of a series of sled and OOP tests are presented in this paper to elaborate on the nature and the magnitude of the ATD's neck response “artifact”. In addition, the complication associated with balancing in-position and OOP requirements as a result of this “artifact” is highlighted.

The purpose of this study is to evaluate the hard tissue injury -predictive value of various thoracic injury criteria when the restraint conditions are varied. Ten right-front passenger human cadaver sled tests are presented, all of which were performed at 48 km/h with nominally identical sled deceleration pulses. Restraint conditions evaluated are 1) force-limiting belt and depowered airbag (4 tests), 2) non-depowered airbag with no torso belt (3 tests), and 3) standard belt and depowered airbag (3 tests). Externally measured chest compression is shown to correspond well with the pre sence of hard tissue injury, regardless of restraint condition, and rib fracture onset is found to occur at approximately 25% chest compression. Peak acceleration and the average spinal acceleration measured at the first and eighth or ninth thoracic vertebrae are shown to be unrelated to the presence of injury, though clear variations in peaks and time histories among restraint conditions can be seen.

This paper presents an approach to analyze experimental data contaminated with noise from Anthropomorphic Test Devices (ATDs). This approach is based on information extraction procedures and they are illustrated through an analysis of Hybrid III 3-year-old and Q3 ATDs test data. The methodology used for extracting information and ATD test data analysis includes optimized filtering, spectral coherence, auto- and cross-correlation analysis, and Kalman filtering. This work investigates promising techniques of extracting information from noisy ATD signals that are not commonly used in the automotive industry.

This paper discusses issues related to the Hybrid III dummy head/neck response due to deploying air bags. The primary issue is the occurrence of large moment at the occypital condyles of the dummy, when the head-rotation with respect to the torso is relatively small. The improbability of such an occurrence in humans is discussed in detail based on the available biomechanical data. A secondary issue is the different anthropometric characteristics of the head/neck region of the Hybrid III dummy when compared to humans. Different modes of interaction between the deploying air bag and the Hybrid III dummy’s neck are discussed. Key features of the dummy’s response in these interaction modes have been described in light of the laxity of the atlanto-occypital joint and the effect of the neck muscle pairs. Issues for improving the biofidelity of the Hybrid III dummy’s neck response due to deploying air bags are discussed.

The Hybrid III family of dummies is used to estimate the response of an occupant during a crash. One recent area of interest is the response of the neck during air bag loading. The biomechanical response of the Hybrid III dummy's neck was based on inertial loading during crash events, when the dummy is restrained by a seat belt and/or seat back. Contact loading resulting from an air bag was not considered when the Hybrid III dummy was designed. This paper considers the effect of air bag loading on the 5th percentile female Hybrid III dummies. The response of the neck is presented in comparison to currently accepted biomechanical corridors. The Hybrid III dummy neck was designed with primary emphasis on appropriate flexion and extension responses using the corridors proposed by Mertz and Patrick. They formulated the mechanical performance requirements of the neck as the relationship between the moment at the occipital condyles and the rotation of the head relative to the torso.

Stochastic simulation is used to account for the uncertainties inherent to the system and enables the study of crash phenomenon. For analytical purposes, random variables such as material crash properties, angle of impact, human response and the like can be characterized using statistical models. The methodology outlined in this approach is based on using the information about the probability of random variables along with structural behavior in order to quantify the scatter in the structural response. Thus the analysis gives a more complete picture of the actual simulation. Practical examples for the use of this technique are demonstrated and an overview of this approach is presented.

The paper presents a comparison between the acceleration pulses of vehicle-to-vehicle crash tests with those of different single-vehicle crash tests. The severity of the full frontal rigid barrier test is compared with that of the vehicle- to-vehicle crash test based on average acceleration and time-to-zero-velocity. Based on this a 30mph full frontal rigid barrier test is found equivalent to a 41mph vehicle-to-vehicle crash. A reduced speed of 22mph for full frontal rigid barrier test is found to represent vehicle-to- vehicle crashes with 50%-100% overlap, with each vehicle travelling at 30mph. The paper also presents a comparison of the acceleration pulses from different crash tests based on the pulse shape and the pulse phase cross-correlation. None of the single-vehicle crash tests have been found to resemble vehicle-to-vehicle crashes in terms of the pulse shape and the pulse phase.

A comparison of the NHTSA advanced dummy, THOR, and the Hybrid III dummy is presented in this paper, based on their performance in four vehicle barrier tests, six HYGE sled tests and twenty two pendulum chest–impact tests. Various time–histories pertaining to accelerations, angular motions, deflections, forces and moments are compared between the two dummies in light of their design difference. In general, in the vehicle crash tests, the resultant head acceleration and chest deflection in THOR are greater than those in the HYBRID III. The shear, axial force and lateral moment in THOR's lumbar are less than those in the Hybrid III in frontal impacts. The differences in the head/chest acceleration and chest deflection could be due to the differences in the construction of the neck and the thorax of the THOR when compared to those of the Hybrid III. The THOR and the Hybrid III have the same level of repeatability in the rear impact sled tests.

The SID-IIs is a small [s], second-generation [II] Side Impact Dummy [SID] which has the anthropometry of a 5th percentile adult female. It has a mass of 43.5 kg, a seated height of 790 mm, and over 100 available data channels. Based on the height and mass, this is equivalent to an average 12-13 year old adolescent. The state-of-the-art SID-IIs has special application in evaluating the performance of side impact airbags. The dummy has undergone prototype testing and will shortly be available for worldwide evaluation. This paper describes the technical details of the dummy, its biomechanical design targets, how well it met those targets, its validation requirements, and its instrumentation. The dummy is the product of a joint development agreement between the Occupant Safety Research Partnership (OSRP) of USCAR and First Technology Safety Systems.