Search Results

1 To meet the Japan Post New-Long-Term (Japan 2009) emissions regulation introduced in 2009, The Hydrocarbon Selective Catalytic Reduction (HC-SCR) system for the NOx emission with a diesel fuel was chosen among various deNOx after-treatment systems (the Urea-SCR, the NOx storage-Reduction Catalyst and so on). The HC-SCR was adopted, in addition to combustion modification of diesel engine (mainly cooled EGR) as the New DPR system. The New DPR system for medium and light duty vehicles was developed as a world's first technology by Hino Motors. Advantages of the New DPR are compact to easy-to-install catalyst converter and no urea solution (DEF) injection (regardless urea infrastructure) as compared the Urea-SCR system.

The emissions reduction potential of neat GTL (Gas to Liquids: Fischer-Tropsch synthetic gas-oil derived from natural gas) fuels has been preliminarily evaluated by three different latest-generation diesel engines with different displacements. In addition, differences in combustion phenomena between the GTL fuels and baseline diesel fuel have been observed by means of a single cylinder engine with optical access. From these findings, one of the engines has been modified to improve both exhaust emissions and fuel consumption simultaneously, assuming the use of neat GTL fuels. The conversion efficiency of the NOx (oxides of nitrogen) reduction catalyst has also been improved.

A 2-LEG NOx Storage-Reduction (NSR) catalyst system is one of potential after-treatment technology to meet stringent NOx and PM emissions standards as Post New Long Term (Japanese 2009 regulation) and US'10. Concerning NOx reduction using NSR catalyst, a secondary fuel injection is necessary to make fuel-rich exhaust condition during the NOx reduction, and causes its fuel penalty. Since fuel injected in the high-temperature (∼250 degrees Celsius) exhaust instantly reacts with oxygen in common diesel exhaust, the proportion of fuel consumption to reduce the NOx stored on NSR catalyst is relatively small. A 2-LEG NSR catalyst system has the decreasing exhaust flow mechanism during NOx reduction, and the potential to improve the NOx reduction and fuel penalty. Therefore, this paper studies the 2-LEG NSR catalyst system. The after-treatment system consists of NSR catalysts, a secondary fuel injection system, flow controlled valves and a Catalyzed Diesel Particulate Filter (CDPF).

Mechanical seals have been applied as sealing devices for water pumps of automotive engines. The mechanical seal plays an important state. Therefore, there are many kinds of constructions. This paper is concerned with the FEM (Finite Element Method) analytical results for various water pump seal construction. It becomes clear that the property of heat transfer is closely related to the sealing durability.

A C-shaped seals is used under severe conditions in which rubber gasket and o-ring can not be used. Furthermore, C-seals exhibit various advantage such as small fitting space and light weight, therefore widely used as sealing elements for rocket engines and automotive engines. And also particular advantage offered by C-seals is good springback, high level of sealing performance under high pressure condition, stretching of the flange bolts. This paper is concerned of the sealing mechanism of C-seal by experimental work and finite element stress analysis. As a result, the lead coated layer on a C-seal has an important function on the sealing performance. In the present paper we describe on an interesting results reached by experiments regarding correlation of helium leakage late and contact pressure.

Mechanical seals have been applied as a sealing device for an automotive air conditioning compressor. Sometimes, the leaking trouble occurs under the conditions such as excessive wear, blistering formation and cracking phenomena on the carbon-ring. This paper is concerned with the analysis of cracking phenomena based upon Finite Element Method (FEM) calculation and experimental investigation.

Instead of end-face type seals, lip-type seals have recently been widely applied as sealing devices for automotive air conditioning compressors, and have shown good sealing performance in practical applications. This paper is concerned with the sealing phenomena of lip-type seals, which run under hydrodynamic lubrication between the lip/shaft surfaces.

C-shaped metal seals (C-seal) are used as static seals under the conditions such as high vacuum, high pressure, high temperature and cryogenic states. The correlation between the sealing performance and design parameters as loading force, deformation, and the surface roughness of ontacting faces have been investigated. This paper is concerned with the relationship between the surface condition of the coated-lead layer of C-seals and the surface roughness of mating flange. The effects of surface condition on leakage are examined fundamentally. Annular coated-lead layer on the surface of a C-seal prevents leakage, though there exist the fine defects or surface irregularities on the flange. It becomes clear from the test results that the surface conditions of the flange and loading force closely relate to the leakage rates with the deflection of C-seal under the. load and the behavior of the contact condition of flange surface.

Mechanical seals have been applied as a sealing device for an automotive air conditioning compressor. However, the leaking trouble occurs under the conditions such as excessive wear, blistering formation and cracking phenomena on the carbon-rings. This paper is concerned with a study of carbon-cracking phenomena.

The turbo-charger of an automotive engine is commonly used for increasing its power characteristics. In this equipment, both sealing and lubricating conditions are important factors and face to difficult technical problems. This paper is concerned with sealing problem for the turbo-charger, and development of low frictional type mechanical seals with good performance and excellent reliability.

A lip seal for use in high-pressure automotive air conditioning compressors has been developed. This paper describes the design and the sealing performance of this new lip seal.

The mechanical seal in automotive water pumps is critical to the performance and reliability of the engine, requiring consistent, effective sealing performance and long operating life. In recent years, the advent of maintenance free performance requirements and increasingly severe operating conditions have resulted in significant changes to the variety and concentration of additives in cooling systems. As a consequence of these changes to the additives, various types of premature seal leakage failures have occurred during service operation. These have been categorized into four types of failure modes and compared with seals providing normal service in order to establish simulated test conditions for engine coolants containing various additives. This paper reports on the various types of failure mechanisms that were found to occur during simulated performance testing and the corrective measures that will eliminate their occurrence

There are various types of super chargers applied for mechanical charging system. Root system is the typical one of them, comprising some varieties such as vane type, spiral type, lysholm type, etc., each of which contains problems of consuming power, heat generation, wear- or other. It is now a big issue for the industry to overcome such problems and this paper refers to the effect of the vane type super charger (ESC-300) which could minimize such problems as less as possible.

End-face type seals (mechanical seals) have been applied as a sealing device for the automotive air conditioning compressor. However, in the practical market, oil or gas leakage from sealing devices sometimes occures based on blistering phenomena of carbon piece and lubricating conditions between rubbing surfaces. The paper presents good sealing performance for the developed face type mechanical seals.

On behalf of a face-type seal (mechanical seal), a new lip type seal for an automotive air conditioning compressor was developed. The paper presents good sealing performance and fundamental of designing for the new seal.

According to the 1982 Japanese Engine Data Book, 249 automobile engine models are used, including gasoline and diesel engines. Among them, 87 models (approximately 60% of all 4-cycle gasoline engine models), are designed for small passenger car applications, with displacements between 1.51 and 2.00. This paper will highlight the area such as Seals for Automobile Engine Applications, Present Automotive Engine Seal Situation in Japan and Countermeasure Activity for Field Claims.

It is clear that excessive lip wear is one of the origin of oil seal leakage in the market. In this paper, follows are discussed; Oil seals used for the rear side of automotive mission gear case have excessive lip wear as typical failure mode, and the sealing characteristics of oil seals is influenced by reciprocating motion of rotational shaft with rough surface.

Improvement of automotive fuel consumption is subject of saving energy today. Oil seals with low friction for automobile are required in the market. In this report, an idea for decreasing the friction of seals and its concreate countermeasure are discussed. It becomes clear that developed low friction seals have good sealing performance as same as present seals.

Types of boot seals for rack and pinion gear of automotive steering and their characteristics are given, and necessary items for designing seals are clarified based on experiments and experiences upon required performances of products.

Types of oil seals for automotive shock absorbers and their characteristics are given, and necessary items for designing seals are clarified based on experiments and experiences upon required performances of products.