Refine Your Search

Search Results

Viewing 1 to 13 of 13
Standard

Qualified Hoses for Marine Applications

2019-12-27
CURRENT
J1942/1_201912
The following list consists of hose data provided as of December, 2019, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a Successfully test their hose to the requirements of SAE J1942, Table 1. b Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table, Table 1) along with the test results.
Standard

Qualified Hoses for Marine Applications

2018-12-31
HISTORICAL
J1942/1_201812
The following list consists of hose data provided as of December 2018, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a Successfully test their hose to the requirements of SAE J1942, Table 1. b Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table on page 4) along with the test results.
Standard

Clip Fastener Fitting

2018-08-24
CURRENT
J1467_201808
This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.
Standard

Automotive Air Brake Hose and Hose Assemblies

2017-10-12
CURRENT
J1402_201710
This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 to +100 °C.
Standard

Qualified Hoses for Marine Applications

2016-12-20
HISTORICAL
J1942/1_201612
The following list consists of hose data provided as of December 2016, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting. This list has been compiled by SAE Staff from information provided by the manufacturers whose product listings appear in this document. Manufacturers wishing to list their products in this document shall: a Successfully test their hose to the requirements of SAE J1942, Table 1. b Submit a letter of certification to the SAE J1942 test requirements for each specific type of hose tested (see sample table on page 4) along with the test results.
Standard

Qualified Hoses for Marine Applications

2015-12-17
HISTORICAL
J1942/1_201512
Effective August 28, 1991, the SAE replaced the USCG as the listing agency for Marine Hose Assemblies. The previous USCG list was discontinued as of December 31, 1992, and is being replaced by this SAE listing, J1942-1. All products appearing on the USCG list as of December 31, 1992, may be carried over to the SAE J1942-1 provided they meet the new test requirements listed in SAE J1942. If your products comply, you may retain your listings with no additional testing. (Please note that the USCG has the authority to request and inspect your test results at their discretion). The following list consists of hose data provided as of December 2015, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting.
Standard

Hydraulic Hose Fitting for Marine Applications

2014-06-05
CURRENT
J1475_201406
This SAE Standard covers general and performance specifications for hydraulic hose fittings of the styles, types, and classes defined in Section 3 and used in conjunction with nonmetallic flexible hoses for marine applications. This document does not ensure compatibility between manufacturers of hydraulic hose and hydraulic hose fittings. Compatibility is the responsibility of the hydraulic hose assembly manufacturer.
Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2014-06-04
CURRENT
J1927_201406
This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.
Standard

Clip Fastener Fitting

2013-02-13
HISTORICAL
J1467_201302
This SAE Standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment primarily in mining applications.
Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2011-10-25
CURRENT
J2631_201110
This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.
Standard

Qualified Hoses for Marine Applications

2010-12-30
HISTORICAL
J1942/1_201012
Effective August 28, 1991, the SAE replaced the USCG as the listing agency for Marine Hose Assemblies. The previous USCG list was discontinued as of December 31, 1992, and is being replaced by this SAE listing, J1942-1. All products appearing on the USCG list as of December 31, 1992, may be carried over to the SAE J1942-1 provided they meet the new test requirements listed in SAE J1942. If your products comply, you may retain your listings with no additional testing. (Please note that the USCG has the authority to request and inspect your test results at their discretion). The following list consists of hose data provided as of December 2010, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25. Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer’s recommended MAWP or type of fitting.
Standard

Automotive Air Brake Hose and Hose Assemblies

2010-08-05
HISTORICAL
J1402_201008
This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 to +100 °C.
Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2009-03-27
HISTORICAL
J1927_200903
This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.
X