Refine Your Search

Topic

Search Results

Standard

Strsw (Squeeze Type Resistance Sport Welding) Equipment Acceptance Criteria for the Collision Repair Industry

2019-10-28
CURRENT
J2667_201910
This SAE Recommended Practice provides a minimum standard for evaluating squeeze-type resistance spot welding (STRSW) equipment and minimum weld performance criteria for two-sided automotive collision repair welding. This document contains several standardized test methods that are designed for evaluating equipment performance in a laboratory environment.
Standard

Vehicle Lift Points for Service Garage Lifting

2019-10-16
CURRENT
J2184_201910
This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.
Standard

Vehicle Passenger Door Hinge Systems

2019-10-09
CURRENT
J934_201910
The scope of this SAE Recommended Practice is to establish recommended uniform test procedures and minimum static load requirements for vehicle passenger door hinge systems. Tests are described that can be conducted on test fixtures and equipment in laboratory test facilities. The test procedures and minimum performance requirements outlined in this document are based on currently available engineering data. It is intended that all portions of the document be periodically reviewed and revised as additional knowledge regarding vehicle hinge system performance under impact conditions is developed.
Standard

Numbering System for Multiple Diameter Cutting Tools

2019-10-09
CURRENT
J2276_201910
This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Single Diameter and Taper Reamers

2019-10-09
CURRENT
J2124_201910
This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Taps

2019-10-09
CURRENT
J2123_201910
This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Single Diameter Drills

2019-10-09
CURRENT
J2122_201910
This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering Systems for End Mills

2019-10-09
CURRENT
J2342_201910
This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Data Security Services

2019-10-09
CURRENT
J1760_201910
The scope of this SAE Recommended Practice is to require the use of the same Security Services as defined by the International Standard ISO/CD 15764, modified by the Class of Security as determined by the resource provider and referenced in Table 1, Extended Data Link Security References.
Standard

Domestic Performance Torque Converter Manufacturing

2019-10-09
CURRENT
J2440_201910
The scope of this SAE Draft Technical Report is to establish dimensional standards for high-performance domestic torque converter manufacturers. Many torque converter manufacturers build converters to their own standards. Some of these standards may be outside of the specifications that define a quality performance torque converter.
Standard

Performance Engine Building Recommended Practices

2019-10-03
CURRENT
J2379_201910
This SAE Recommended Practice applies to the function of building reciprocating spark-ignition engines which are used in conjunction with standard and high-performance ancillary components in applications intended to achieve a minimum of 1 hp/in3. This document does not apply to rebuilt engines which may only be partially repaired with little or no machining, nor does it apply to second-hand or used engines.
Standard

Film Analysis Guides for Dynamic Studies of Test Subjects

2019-10-02
CURRENT
J138_201910
This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.
Standard

Motor Vehicle Seating Systems

2019-10-02
CURRENT
J879B_201910
This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.
Standard

Filter and Filter Element for Hydraulic System(s) Used on Manufacturing and Assembly Equipment

2019-10-02
CURRENT
J2066_201910
This SAE Standard establishes a common specification and ordering code for hydraulic filter assemblies and hydraulic filter elements, and establishes minimum performance criteria and test methods. This document establishes two filter diameter sizes, five basic micron ratings, and two basic collapse ratings. These classifications will satisfy most hydraulic filter applications, and thereby can minimize inventory requirements for hydraulic filter elements.
Standard

Uniform Reference and Dimensional Guidelines for Collision Repair

2014-06-26
HISTORICAL
J1828_201406
This SAE Recommended Practice defines, for vehicle manufacturers and collision information and equipment providers, the types of vehicle dimensional data needed by the collision repair industry and aftermarket equipment modifiers to properly perform high-quality repairs to damaged vehicles. Both bodyframe and unitized vehicles, including passenger cars and light trucks, are addressed.
Standard

Heavy-Duty Starter Remanufacturing Procedures

2008-11-26
CURRENT
J2237_200811
These remanufacturing procedures are recommended minimum guidelines (with the understanding that more stringent procedures are acceptable) for use by remanufacturers of heavy-duty starters to promote consistent reliability, durability, and safety of remanufactured starters. Installation of remanufactured or rebuilt products is often an economical way to repair an application even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing so as to provide durable operation of the part as well as acceptable performance when installed on the application. The remanufacturer should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding their product.
Standard

Starter Armature Remanufacturing Procedures

2008-11-26
CURRENT
J2240_200811
These remanufacturing procedures are recommended guidelines for use by remanufacturers of starter armatures to promote consistent reliability, durability, and safety of remanufactured starters. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core is suitable for remanufacturing so as to provide durable operation of the part as well as acceptable performance when installed on the vehicle. The remanufacturer should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding their product.
Standard

Automotive Starter Solenoid Remanufacturing Procedures

2008-11-26
CURRENT
J2242_200811
These remanufacturing procedures are recommended guidelines for use by remanufacturers of starter solenoids to promote consistent reliability, durability, and safety of remanufactured starters. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core is suitable for remanufacturing so as to provide durable operation of the part as well as acceptable performance when installed on the vehicle. The remanufacturer should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding their product.
X