Refine Your Search

Date

Date

Topic

Topic

Diesel / compression ignition engines Engine components Motor Vehicle Council Production Identification Chemicals Wear

Search Results

Viewing 1 to 20 of 37
12Next >Last >>
Sort by published
Standard

Vehicle Lift Points for Service Garage Lifting
2019-10-16
CURRENT
J2184_201910
This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.
Standard

Numbering Systems for End Mills
2019-10-09
CURRENT
J2342_201910
This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Data Security Services
2019-10-09
CURRENT
J1760_201910
The scope of this SAE Recommended Practice is to require the use of the same Security Services as defined by the International Standard ISO/CD 15764, modified by the Class of Security as determined by the resource provider and referenced in Table 1, Extended Data Link Security References.
Standard

Numbering System for Single Diameter and Taper Reamers
2019-10-09
CURRENT
J2124_201910
This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Single Diameter Drills
2019-10-09
CURRENT
J2122_201910
This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Multiple Diameter Cutting Tools
2019-10-09
CURRENT
J2276_201910
This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Taps
2019-10-09
CURRENT
J2123_201910
This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Performance Engine Building Recommended Practices
2019-10-03
CURRENT
J2379_201910
This SAE Recommended Practice applies to the function of building reciprocating spark-ignition engines which are used in conjunction with standard and high-performance ancillary components in applications intended to achieve a minimum of 1 hp/in3. This document does not apply to rebuilt engines which may only be partially repaired with little or no machining, nor does it apply to second-hand or used engines.
Standard

Film Analysis Guides for Dynamic Studies of Test Subjects
2019-10-02
CURRENT
J138_201910
This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.
Standard

Filter and Filter Element for Hydraulic System(s) Used on Manufacturing and Assembly Equipment
2019-10-02
CURRENT
J2066_201910
This SAE Standard establishes a common specification and ordering code for hydraulic filter assemblies and hydraulic filter elements, and establishes minimum performance criteria and test methods. This document establishes two filter diameter sizes, five basic micron ratings, and two basic collapse ratings. These classifications will satisfy most hydraulic filter applications, and thereby can minimize inventory requirements for hydraulic filter elements.
Standard

Seat Belt Hardware Webbing Abrasion Test Procedure
2013-06-11
CURRENT
J339_201306
This SAE Recommended Practice describes a test procedure for evaluating the abrasion resistance characteristics of webbing when used in hardware of seat belt assemblies such as those described in SAE J140.
Standard

Seat Belt Hardware Webbing Abrasion Performance Requirements
2013-06-11
CURRENT
J114_201306
This SAE Recommended Practice describes the performance requirements for abrasion resistance of webbing when used in adjustment hardware normally used to adjust the length of seat belt assemblies such as those described in SAE J140. These requirements are applicable to tests conducted according to the procedure described in SAE J339. Although adjustment hardware is normally the primary source of webbing abrasion in a seat belt assembly, consideration should be given to other areas of normal webbing contact in the restraint system that may provide a more severe condition of webbing abrasion.
Standard

Heavy-Duty Starter Remanufacturing Procedures
2008-11-26
CURRENT
J2237_200811
These remanufacturing procedures are recommended minimum guidelines (with the understanding that more stringent procedures are acceptable) for use by remanufacturers of heavy-duty starters to promote consistent reliability, durability, and safety of remanufactured starters. Installation of remanufactured or rebuilt products is often an economical way to repair an application even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing so as to provide durable operation of the part as well as acceptable performance when installed on the application. The remanufacturer should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding their product.
Standard

Automotive Starter Remanufacturing Procedures
2008-06-09
CURRENT
J2073_200806
These manufacturing procedures are recommended minimum guidelines for use by remanufacturers of light-duty automotive starters to promote consistent reliability, durability, and safety of remanufactured starters. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing so as to provide durable operation of the part as well as acceptable performance when installed on the vehicle. The remanufacturer should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding their product.
Standard

Alternator Remanufacturing/Rebuilding Procedures Includes Passenger Car, Heavy Duty, Industrial, Agricultural, and Marine
2008-05-13
CURRENT
J2075_200805
These remanufacturing procedures are recommended minimum guidelines (with theunderstanding that being more critical is acceptable) for use by remanufacturers/rebuilders of alternators to promote consistent reliability, durability, and safety of remanufactured alternators. Installation of remanufactured or rebuilt products is often an economical way to repair an application even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer/rebuilder should determine if the original design and present condition of the core are suitable for remanufacturing/rebuilding so as to provide durable operation of the part as well as acceptable performance when installed on the application. The remanufacturer/rebuilder should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding this product.
Standard

Vehicle Lift Points for Service Garage Lifting
2007-09-27
HISTORICAL
J2184_200709
This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.
12Next >Last >>
X