Search Results

This SAE Recommended Practice describes test procedures for evaluating hardware used in motor vehicle seat belt assemblies. Related hardware performance requirements are described in SAE J141. Test procedures and performance requirements for retractors will be covered in separate SAE Recommended Practices to be issued later.

This SAE Recommended Practice provides a minimum standard for evaluating squeeze-type resistance spot welding (STRSW) equipment and minimum weld performance criteria for two-sided automotive collision repair welding. This document contains several standardized test methods that are designed for evaluating equipment performance in a laboratory environment.

This SAE Recommended Practice is intended to provide guidelines to the vehicle manufacturer for applying recovery attachment points on vehicles rated up to 3178 kg (7000 lb) GVW, such as passenger cars, vans, and light trucks.

This SAE Recommended Practice provides a means for evaluating the drivetrain of the passenger car, van, or light-duty truck being towed under a variety of road conditions. The towing equipment used is explained in SAE J1142. NOTE—For the purpose of this document, the drivetrain refers to the combination of a specific transmission (make, model, size, type), a specific differential assembly (make, model, size, type), and a specific driveline, if required.

This SAE Recommended Practice defines, for vehicle manufacturers and collision information and equipment providers, the types of vehicle dimensional data needed by the collision repair industry and aftermarket equipment modifiers to properly perform high-quality repairs to damaged vehicles. Both bodyframe and unitized vehicles, including passenger cars and light trucks, are addressed.

This SAE Recommended Practice provides a means to observe and evaluate a towed vehicle under a variety of road conditions to determine its behavior. The drivetrain should be evaluated by conducting SAE J1144.

This SAE Recommended Practice is designed to provide readily accessible paint and trim code information on all passenger vehicles, lightweight trucks, and vans in a way that minimizes the time and effort required to locate and effectively use that information for body repair, parts ordering, vehicle maintenance, and information systems.

This SAE Standard is directed at the proper communication of the lift points on the vehicle frame or underbody to commercial service personnel for the purpose of raising passenger vehicles, light trucks, and vans completely off the shop floor. To this end, vehicle manufacturers are guided in the proper design of a lift point label and lift points located on the body/frame for use by service garages.

This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

The scope of this SAE Recommended Practice is to require the use of the same Security Services as defined by the International Standard ISO/CD 15764, modified by the Class of Security as determined by the resource provider and referenced in Table 1, Extended Data Link Security References.

Almost all light trucks now are being manufactured with at least a driver side air bag and all will have dual air bags by 1998. The driving forces behind this feature are occupant safety, federal regulations, and competition in the industry. Along with the booming popularity of pickups and SUVs, they are commonly accessorized with a wide variety of products. Many accessories for four-wheel drives in particular are mounted on the front of the vehicle. These products include grille/brush guards, winches, snow plows, replacement bumpers, bicycle carriers, etc. Concerns have arisen over the compatibility of these accessories with the vehicle’s air bag system. The vehicle manufacturers are concerned because of their huge investment in design and crash test verification of the complete vehicle system and keen awareness of the federal regulations. The crushability of the front bumper and supporting structure are key elements in the system, so alterations to that area become logical concerns.

The scope of this SAE Recommended Practice is to establish recommended uniform test procedures and minimum static load requirements for vehicle passenger door hinge systems. Tests are described that can be conducted on test fixtures and equipment in laboratory test facilities. The test procedures and minimum performance requirements outlined in this document are based on currently available engineering data. It is intended that all portions of the document be periodically reviewed and revised as additional knowledge regarding vehicle hinge system performance under impact conditions is developed.

This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

This SAE Recommended Practice provides a systematic method for the identification of single diameter drills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying drills that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.

This SAE Recommended Practice establishes minimum performance requirements and test procedures for evaluating and testing passenger car side door latch systems. It is limited to tests that can be conducted on uniform test fixtures and equipment in commercially available laboratory test facilities. The test procedures and minimum performance requirements outlined in this document are based on currently available engineering data. It is intended that all portions of the document will be periodically reviewed and revised, as additional knowledge regarding vehicle latch performance under impact conditions is developed.

The scope of this SAE Recommended Practice is restricted to the testing of original equipment on passenger vehicles and to provide for a uniform industry test procedure.

This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.

This SAE Standard is a truth-in-labeling standard for map databases.