Refine Your Search

Search Results

Viewing 1 to 16 of 16
Standard

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than 2032 mm in Overall Width

2018-08-28
CURRENT
J575_201808
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
Standard

Highly Accelerated Failure Test (HAFT) for Automotive Lamps with LED Assembly

2018-05-20
CURRENT
J3014_201805
This SAE Recommended Practice provides test procedures, requirements, and equipment recommendations for the methods of the measurement that characterizes potential design failures by utilizing a step stress approach to subject a device under test to thermal, vibration, and electrical stresses of types and levels beyond what it may see in actual use, but which will rapidly induce failure modes, allowing them to be detected and corrected.
Standard

Photometry Laboratory Accuracy Guidelines

2017-04-24
WIP
J1330
The purpose of this SAE Information Report is to list and explain major equipment, instrumentation, and procedure variables which can affect inter-laboratory differences and repeatability of photometric measurements of various lighting devices listed in SAE Technical Reports. The accuracy guidelines listed in the report are for the purpose of controlling variables that are not a direct function of the lighting device being measured. The control of these individual variables is necessary to control the overall accuracy of photometric measurements. These accuracy guidelines apply to the measurement of the luminous intensities and reflected intensities of devices at the specified geometrically distributed test points and areas. These guidelines do not apply to photometric equipment used to measure license plate lamps.
Standard

Camera-based Light Measurement Techniques

2014-06-26
WIP
J3100
This recommended practice describes the application of digital cameras to measurement of photometric quantities in the photometric laboratory.
Standard

Highly Accelerated Failure Test (HAFT) for Automotive Lamps with LED Assembly

2013-03-26
HISTORICAL
J3014_201303
This SAE Recommended Practice provides test procedures, requirements, and equipment recommendations for the methods of the measurement that characterizes potential design failures by utilizing a step stress approach to subject a device under test to thermal, vibration, and electrical stresses of types and levels beyond what it may see in actual use, but which will rapidly induce failure modes, allowing them to be detected and corrected.
Standard

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than 2032 mm in Overall Width

2012-04-11
HISTORICAL
J575_201204
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
Standard

SAE Miniature Bulb Vibration Test

2011-08-29
HISTORICAL
J1765_201108
This SAE Recommended Practice was designed to be an accelerated vibration test that subjects bulbs to critical vibration/shock loading typically observed in normal vehicle service and can be employed for conformance of production (COP) testing. The test was designed for external vehicle applications.
Standard

Test Methods and Equipment for Lighting Devices and Components for Use on Vehicles Less than 2032 mm in Overall Width

2006-11-21
HISTORICAL
J575_200611
This SAE Recommended Practice provides standardized laboratory tests, test methods, and requirements applicable to many of the lighting devices and components covered by SAE Recommended Practices and Standards and is intended for reference for devices used on vehicles less than 2032 mm in width, regardless of length, or 7620 mm in length regardless of width. Tests for vehicles larger than 2032 mm in overall width are covered in J2139.
Standard

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than 2032 mm in Overall Width

1983-07-01
HISTORICAL
J575_198307
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
Standard

Photometry Laboratory Accuracy Guidelines

1982-08-01
HISTORICAL
J1330_198208
The purpose of this SAE Information Report is to list and explain major equipment, instrumentation, and procedure variables which can affect inter-laboratory differences and repeatability of photometric measurements of various lighting devices listed in SAE Technical Reports. The accuracy guidelines listed in the report are for the purpose of controlling variables that are not a direct function of the lighting device being measured. The control of these individual variables is necessary to control the overall accuracy of photometric measurements. These accuracy guidelines apply to the measurement of the luminous intensities and reflected intensities of devices at the specified geometrically distributed test points and areas. These guidelines do not apply to photometric equipment used to measure license plate lamps.
Standard

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than 2032 mm in Overall Width

1977-09-01
HISTORICAL
J575G_197709
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
Standard

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than 2032 mm in Overall Width

1975-04-01
HISTORICAL
J575F_197504
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
Standard

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than 2032 mm in Overall Width

1966-06-01
HISTORICAL
J575C_196606
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
Standard

Test Methods and Equipment for Lighting Devices for Use on Vehicles Less than 2032 mm in Overall Width

1961-06-01
HISTORICAL
J575_196106
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
X