Search Results

Higher compression ratio and turbocharging, with engine downsizing can enable significant gains in fuel economy but require engine operating conditions that cause engine knock under high load. Engine knock can be avoided by supplying higher-octane fuel under such high load conditions. This study builds on previous MIT papers investigating Octane-On-Demand (OOD) to enable a higher efficiency, higher-boost higher compression-ratio engine. The high-octane fuel for OOD can be obtained through On-Board-Separation (OBS) of alcohol blended gasoline. Fuel from the primary fuel tank filled with commercially available gasoline that contains 10% by volume ethanol (E10) is separated by an organic membrane pervaporation process that produces a 30 to 90% ethanol fuel blend for use when high octane is needed. In addition to previous work, this paper combines modeling of the OBS system with passenger car and medium-duty truck fuel consumption and octane requirements for various driving cycles.

Passenger cars in the United States continue to incorporate increasing levels of technology and features. However, deployment of technology requires substantial development and time in the automotive sector. Prior analyses indicate that deployment of technology in the automotive sector can be described by a logistic function. These analyses refer to maximum annual growth rates as high as 17% and with developmental times of 10-15 years. However, these technologies vary widely in complexity and function, and span decades in their implementation. This work applies regression with a logistic form to a wide variety of automotive features and technologies and, using secondary regression, identifies broader trends across categories and over time.

This vehicle simulation study estimates the fuel economy benefits of an HCCI engine system and assesses the NOx, HC and CO aftertreatment performance required for compliance with emissions regulations on U.S. and European regulatory driving cycles. The four driving cycles considered are the New European Driving Cycle, EPA City Driving Cycle, EPA Highway Driving Cycle, and US06 Driving Cycle. For each driving cycle, the following influences on vehicle fuel economy were examined: power-to-weight ratio, HCCI combustion mode operating range, driving cycle characteristics, requirements for transitions out of HCCI mode when engine speeds and loads are within the HCCI operating range, fuel consumption and emissions penalties for transitions into and out of HCCI mode, aftertreatment system performance and tailpipe emissions regulations.

This paper assesses the potential improvement of automotive powertrain technologies 25 years into the future. The powertrain types assessed include naturally-aspirated gasoline engines, turbocharged gasoline engines, diesel engines, gasoline-electric hybrids, and various advanced transmissions. Advancements in aerodynamics, vehicle weight reduction and tire rolling friction are also taken into account. The objective of the comparison is the potential of anticipated improvements in these powertrain technologies for reducing petroleum consumption and greenhouse gas emissions at the same level of performance as current vehicles in the U.S.A. The fuel consumption and performance of future vehicles was estimated using a combination of scaling laws and detailed vehicle simulations. The results indicate that there is significant potential for reduction of fuel consumption for all the powertrains examined.

An experimental study was performed to investigate the effects of various intake charge motion control valves (CMCVs) on mixture preparation, combustion, and hydrocarbon (HC) emissions during the cold start-up process of a port fuel injected spark ignition (SI) engine. Different charge motions were produced by three differently shaped plates in the CMCV device, each of which blocked off 75% of the engine's intake ports. Time-resolved HC, CO and CO2 concentrations were measured at the exhaust port exit in order to achieve cycle-by-cycle engine-out HC mass and in-cylinder air/fuel ratio. Combustion characteristics were examined through a thermodynamic burn rate analysis. Cold-fluid steady state experiments were carried out with the CMCV open and closed. Enhanced charge motion with the CMCV closed was found to shorten the combustion duration, which caused the location of 50% mass fraction burned (MFB) to occur up to 5° CA earlier for the same spark timing.

A set of experiments was performed to investigate the effects of relative air-fuel ratio, inlet boost pressure, and compression ratio on engine knock behavior. Selected operating conditions were also examined with simulated hydrogen rich fuel reformate added to the gasoline-air intake mixture. For each operating condition knock limited spark advance was found for a range of octane numbers (ON) for two fuel types: primary reference fuels (PRFs), and toluene reference fuels (TRFs). A smaller set of experiments was also performed with unleaded test gasolines. A combustion phasing parameter based on the timing of 50% mass fraction burned, termed “combustion retard”, was used as it correlates well to engine performance. The combustion retard required to just avoid knock increases with relative air-fuel ratio for PRFs and decreases with air-fuel ratio for TRFs.

This paper explores the modeling of a lean boosted engine concept. Modeling provides a useful tool for investigating different parameters and comparing resultant emissions and fuel economy performance. An existing architectural concept has been tailored to a boosted hydrogen-enhanced lean-burn SI engine. The simulation consists of a set of Matlab models, part physical and part empirical, which has been developed to simulate a working engine. The model was calibrated with production engine data and experimental data taken at MIT. Combustion and emissions data come from a single cylinder research engine and include changes in air/fuel ratio, load and speed, and different fractions of the gasoline fuel reformed to H2 and CO. The outputs of the model are brake specific NOx emissions and brake specific fuel consumption maps along with cumulative NOx emissions and fuel economy for urban and highway drive cycles.

Modern natural gas-to-liquids (GTL) conversion processes (Fischer-Tropsch liquid fuels (FTL)) offers an attractive means for making synthetic liquid fuels. Military diesel and jet fuels are procured under Commercial Item Description (CID) A-A-52557 (based on ASTM D 975) and MIL-DTL-83133/MIL-DTL-5624 (JP-8/JP-5), respectively. The Single Fuel Forward (single fuel in the battlefield) policy requires the use of JP-8 or JP-5 (JP-8/5). Fuel properties crucial to fuel system/engine performance/operation are identified for both old and new tactical/non-tactical vehicles. The 21st Century Truck program is developing technology for improved safety, reduced harmful exhaust emissions, improved fuel efficiency, and reduced cost of ownership of future military and civilian ground vehicles (in the heavy duty category having gross vehicle weights exceeding 8500 pounds).[1]

Currently, states that are out of compliance with the National Ambient Air Quality Standards must, according to the Clean Air Act Amendments of 1990 (CAAA), develop and implement control strategies that demonstrate specific degrees of reduction in emissions-with the degree of reduction depending upon the severity of the problem. One tool that has been developed to aid regulators in both deciding an appropriate course of action and to demonstrate the desired reductions in mobile emissions is EPA's Mobile 5a emission estimation model. In our study, Mobile 5a has been used to examine the effects of regulatory strategies, as applied to the Northeast United States, on vehicle emissions under worst-case ozone-forming conditions.

This paper reviews the major changes that have occurred in spark-ignition engine design and operation over the last two decades. The automobile air pollution problem, automobile emission standards, and automobile fuel economy standards -- the factors which have and are producing these changes -- are briefly described. The major components in spark-ignition engine emission control systems are outlined, and advances in carburetion, fuel injection, ignition systems, spark retard and exhaust gas recycle strategies, and catalytic converters, are reviewed. The impact of these emission controls on vehicle fuel economy is assessed. The potential for fuel economy improvements in conventional spark-ignition engines is examined, and promising developments in improved engine and vehicle matching are outlined.