Search Results

This paper describes the after-treatment technology that could be used to meet a future BS-VII standard, considering close-coupled SCR (cc-SCR) to help start NOx conversion earlier. Both active (Cu/Fe-SCR based) and passive (V-SCR based) systems have the potential to meet emission limits. V-SCR may be considered in the rear position because V-SCR shows a fast response with very low N2O formation. Next-gen V-SCR technology shows significantly improved performance and durability closer to Cu-SCR. The steady-state NOx conversions over Next-Gen V-SCR were better than BS-VI V-SCR in both fresh and aged-580°C/100h conditions. High durability was also observed after engine aging of 1000h (WHTC + high load). Another big challenge in BS VII could be the PN10 requirement. With enhanced filtration coating (EFC) technology, PN emissions drop drastically in comparison to Euro VI reference without EFC to meet a future BS VII.

Selective Catalytic Reduction (SCR) systems have been demonstrated as effective solutions for controlling NOx emissions from Heavy Duty diesel engines. Future HD diesel engines are being designed for higher engine out NOx to improve fuel economy, while discussions are in progress for tightening NOx emissions from HD engines post 2020. This will require increasingly higher NOx conversions across the emission control system and will challenge the current aftertreatment designs. Typical 2010/2013 Heavy Duty systems include a diesel oxidation catalyst (DOC) along with a catalyzed diesel particulate filter (CDPF) in addition to the SCR sub-assembly. For future aftertreatment designs, advanced technologies such as cold start concept (dCSC™) catalyst, SCR coated on filter (SCRF® hereafter referred to as SCR-DPF) and SCR coated on high porous flow through substrates can be utilized to achieve high NOx conversions, in combination with improved control strategies.

Selective Catalytic Reduction (SCR) catalysts have been demonstrated as an effective solution for controlling NOx emissions from diesel engines. Typical 2013 Heavy Duty Diesel emission control systems include a DOC upstream of a catalyzed soot filter (CSF) which is followed by urea injection and the SCR sub-assembly. There is a strong desire to further increase the NOx conversion capability of such systems, which would enable additional fuel economy savings by allowing engines to be calibrated to higher engine-out NOx levels. One potential approach is to replace the CSF with a diesel particulate filter coated with SCR catalysts (SCRF® technology, hereafter referred to as SCR-DPF) while keeping the flow-through SCR elements downstream, which essentially increases the SCR volume in the after-treatment assembly without affecting the overall packaging.

Selective Catalytic Reduction (SCR) systems have been demonstrated as effective solutions for controlling NOx emissions from Heavy Duty diesel engines. Future HD diesel engines are being designed for higher engine out NOx to improve fuel economy, which will require increasingly higher NOx conversion to meet emission regulations. For future aftertreatment designs, advanced technologies such as SCR coated on filter (SCRF®) and SCR coated on high porous flow through substrates can be utilized to achieve high NOx conversion. In this work, different options were evaluated for achieving high NOx conversion. First, high performance NOx control catalysts were designed by using SCRF unit followed by additional SCR on high porosity substrates. Second, different control strategies were evaluated to understand the effect of reductant dosing strategy and thermal management on NOx conversion. Tests were carried out on a HD engine under transient test cycles.

Selective Catalytic Reduction (SCR) catalysts have been demonstrated as an effective solution for controlling NOx emissions from diesel engines. Typical 2010 Heavy-Duty systems include a DOC along with a catalyzed soot filter (CSF) in addition to the SCR sub-assembly. There is a strong desire to further increase the NOx conversion capability of such systems, to enable additional fuel economy savings by allowing engines to be calibrated to higher engine-out NOx levels. One potential approach is to replace the CSF with a diesel particulate filter coated with SCR catalysts (SCR-DPF) while keeping the flow-through SCR elements downstream, which essentially increases the SCR volume in the after-treatment assembly without affecting the overall packaging. In this work, a system consisting of SCR-DPF was evaluated in comparison to the DOC + CSF components from a commercial 2010 DOC + CSF + SCR system on an engine with the engine EGR on (standard engine-out NOx) and off (high engine-out NOx).

The modern Diesel engine is one of the most versatile power sources available for mobile applications. The high fuel economy and torque of the Diesel engine has long resulted in global application for heavy-duty applications. Moreover, the high power and excellent driveability of today's turbo-charged small high-speed Diesel engines, coupled with their low CO2 emissions, has resulted in an increasing demand for Diesel powered light-duty vehicles. However, the demand for Diesel vehicles can only be realised if their exhaust emissions meet the increasingly stringent emissions legislation being introduced around the world. In the USA, both HDD and LDD vehicles are meeting strict emissions legislations since 2007 with the introduction of particle filters which will be further restricted from 2010 with the use of additional NOx contr5ol systems. In Europe, similar strict requirements are being implemented with Euro IV, Euro V and finally through Euro VI legislations.

The application of oxidation catalyst and particulate filter technology for the reduction of particulate matter (PM), hydrocarbons (HC) and carbon monoxide (CO) emissions from heavy duty diesel engines has become an established practice. The design and performance of such systems have been commercially proven to the point that the application of these technologies is cost effective and durable. The application of an effective NOx reduction technology in heavy duty diesel applications is more complicated since there are no passive NOx reduction technologies that can be fit onto HDD vehicles. However, Selective Catalytic Reduction (SCR) systems using Urea injection to achieve NOx reduction have become the technology of choice in Europe and have been applied to achieve Euro IV emissions levels on new HDD vehicles. In addition, retrofit SCR emission control systems have also been developed that can provide high NOx reduction when applied on existing HDD vehicles.

Six 2001 International Class 6 trucks participated in a project to determine the impact of gas-to-liquid (GTL) fuel and catalyzed diesel particle filters (DPFs) on emissions and operations from December 2003 through August 2004. The vehicles operated in Southern California and were nominally identical. Three vehicles operated “as-is” on California Air Resources Board (CARB) specification diesel fuel and no emission control devices. Three vehicles were retrofit with Johnson Matthey CCRT® (Catalyzed Continuously Regenerating Technology) filters and fueled with Shell GTL Fuel. Two rounds of emissions tests were conducted on a chassis dynamometer over the City Suburban Heavy Vehicle Route (CSHVR) and the New York City Bus (NYCB) cycle. The CARB-fueled vehicles served as the baseline, while the GTL-fueled vehicles were tested with and without the CCRT filters. Results from the first round of testing have been reported previously (see 2004-01-2959).

The retrofitting of diesel engines with oxidation catalyst and particulate filter technology for the reduction of particulate matter (PM), hydrocarbons (HC) and carbon monoxide (CO) emissions has become an established practice. The design and performance of such systems have been commercially proven to the point that the application of these technologies is a cost effective means for states to effectively meet pollution reduction goals. One of the reasons that these technologies are so widely applied is because they can be sized and fitted based on easily measurable vehicle parameters and published engine emission information. These devices generally work passively with basic temperature and back pressure monitoring devices being used to alert the operator to upset conditions. The application of an effective NOx reduction technology in similar retrofit installation, is more complicated. There are no passive NOx reduction technologies that can be retrofit onto HDD vehicles.

The New York State Department of Environmental Conservation (DEC) and Environment Canada have jointly participated along with partners the New York City Metropolitan Transit Agency (MTA); Johnson Matthey, Environmental Catalysts & Technologies; Equilon Enterprises, LLC and Corning, Inc. in a project to evaluate the effect of various combinations of fuels and aftertreatment configurations on diesel emissions. Emissions measurements were performed during engine dynamometer testing of an International DT 466E heavy-duty diesel engine. Fuels tested in the study were Diesel Fuel 1 and 2, low sulfur diesel (150 ppm), two ultralow sulfur fuels (<30 ppm), Fischer-Tropsch, Biodiesel, PuriNOx™ and two Ethanol-Diesel blends. Configurations tested were: engine out, and diesel oxidation catalyst, continuously regenerating diesel filter, and exhaust gas recirculation aftertreatment. In general, the use of more aggressive aftertreatment (ie.

With growing concerns about NOx and particulate matter (PM) emissions from diesel engines, stricter regulations are being implemented which require advanced emission control technology. This paper discusses the combination of a diesel particle filter system (DPF) with a low pressure exhaust gas re-circulation (EGR) system to provide four way emission control of NOx, PM, CO and HC from existing heavy duty diesel engines. The combined EGR-DPF system has been used in Europe over the past 4 years, with over 1200 systems installed on urban buses and other on-road applications. This system has shown 40-60% NOx reduction in addition to >90% CO, HC and PM reductions. Recently, several field trial programs have been initiated to evaluate the performance and durability of this EGR-DPF system under US operational conditions. These include retrofit applications on urban buses and on construction trucks.

In urban areas, particulate emission from diesel engines is one of the pollutants of most concern. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled, “Clean Diesel Vehicle Air Quality Project” has been initiated by NY City Transit under the supervision of NYSDEC and with active participation from several industry partners. Under this program, 25 NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter systems and have been operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses were evaluated over a 9 month period for operations, maintainability and durability of the particulate filter.

A program has been completed to evaluate ultra-low sulfur diesel fuels and passive diesel particulate filters (DPFs) in truck and bus fleets operating in southern California. The fuels, ECD and ECD-1, are produced by ARCO (a BP Company) and have less than 15 ppm sulfur content. Vehicles were retrofitted with two types of catalyzed DPFs, and operated on ultra-low sulfur diesel fuel for over one year. Exhaust emissions, fuel economy and operating cost data were collected for the test vehicles, and compared with baseline control vehicles. Regulated emissions are presented from two rounds of tests. The first round emissions tests were conducted shortly after the vehicles were retrofitted with the DPFs. The second round emissions tests were conducted following approximately one year of operation. Several of the vehicles retrofitted with DPFs accumulated well over 100,000 miles of operation between test rounds.

Particulate emission from diesel engines is one of the most important pollutants in urban areas. With increasing worldwide regulatory requirements to lower particulate matter (PM) standards for heavy duty diesel powered vehicles, the interest in diesel particulate filter based emission control solutions such as the Continuously Regenerating Technology (CRT®) have significantly increased. This system has been applied to thousands of heavy-duty diesel vehicles in Europe over the last six years to meet various local and governmental requirements, while recently introduced in the US. Among the numerous demonstration programs taking place in the US, one important one is the evaluation of CRT filter systems on urban transit buses in NY City. Here, several NY City transit buses with DDC Series 50 engines have been equipped with CRT filters and operating on ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000.

Particulate emission control from diesel engines is one of the major concerns in the urban areas in California. Recently, regulations have been proposed for stringent PM emission requirements from both existing and new diesel engines. As a result, particulate emission control from urban diesel engines using advanced particulate filter technology is being evaluated at several locations in California. Although ceramic based particle filters are well known for high PM reductions, the lack of effective and durable regeneration system has limited their applications. The continuously regenerated diesel particulate filter (CRDPF) technology discussed in this presentation, solves this problem by catalytically oxidizing NO present in the diesel exhaust to NO2 which is utilized to continuously combust the engine soot under the typical diesel engine operating condition.

Particulate emission from diesel engines is one of the most important pollutants in urban areas. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled “Clean Diesel Demonstration Program” has been initiated by NY City Transit under the supervision of NY State DEC and with active participation from several industrial partners. Under this program, several NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter system and are operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses are being evaluated over a 8-9 month period for operations, maintainability and durability of the particulate filter.

Previous studies have shown that regenerating particulate filters are very effective at reducing particulate matter emissions from diesel engines. Some particulate filters are passive devices that can be installed in place of the muffler on both new and older model diesel engines. These passive devices could potentially be used to retrofit large numbers of trucks and buses already in service, to substantially reduce particulate matter emissions. Catalyst-type particulate filters must be used with diesel fuels having low sulfur content to avoid poisoning the catalyst. A project has been launched to evaluate a truck fleet retrofitted with two types of passive particulate filter systems and operating on diesel fuel having ultra-low sulfur content. The objective of this project is to evaluate new particulate filter and fuel technology in service, using a fleet of twenty Class 8 grocery store trucks. This paper summarizes the truck fleet start-up experience.

The EPA implemented the Urban Bus Retrofit/Rebuild (UBRR) Program for transit buses built before 1994 in an effort to lower the amount of PM emissions in densely populated urban areas. The objective of the program is to provide certified emission control technologies that reduce PM emissions from older buses by 25% or to below 0.1 g/bhp-hr. This paper reviews the development of a retrofit kit that has been certified under the UBRR program to meet the 0.1 g/bhp-hr PM emission requirements on DDC 6V92TA engines with both mechanical (MUI) and electronic (DDEC) fuel injection controls. The kit is a combination of specific and modified engine parts and a catalytic exhaust after-treatment device. The kit replaces existing parts with a new camshaft, a uniquely configured cylinder kit and specified turbocharger, blower and injector. For the MUI engines the cam timing, injector height and fuel modulator are set at specific values to achieve the lowest possible PM level.