Search Results

Recuperated low-pressure-ratio split-cycle engines represent a promising engine configuration for applications like transportation and stand-alone power generation by offering a potential efficiency as high as 60%. However, it can be challenging to achieve the stringent NOx emission standard, such as Euro 6 limit of 0.4 gNOx/kWh, due to the exhaust cylinder high intake temperature. This paper presents experimental investigation of hydrogen-air combustion NOx emissions for such engines for the first time. Experiments are carried out using a simplified constant-volume combustion chamber with glow-plug ignition. Two fuel injection techniques are performed: direct injection and injection via a novel convergent-divergent injector. For the direct injection scenario, NOx levels are unsatisfactory with respect to the Euro 6 standards over a range of operating temperatures from 200 °C to 550 °C.

Modern automotive powertrains are operated using many control devices under a wide range of environmental conditions. The exhaust temperature must be controlled within a specific range to ensure low exhaust-gas emissions and engine-component protection. In this regard, physics-based exhaust-temperature prediction models are advantageous compared with the conventional exhaust-temperature map-based model developed using engine dyno testing results. This is because physics-based models can predict exhaust-temperature behavior in conditions not measured for calibration. However, increasing the computational load to illustrate all physical phenomena in the engine air path, including combustion in the cylinder, may not fully leverage the advantages of physical models for the performance of electric control units (ECUs).

To realize a super-leanburn SI engine with a very-high compression ratio, it is required to design a new fuel which could have low ignitability at a low temperature for antiknocking, but high ignitability at a high temperature for stable combustion. Ethane shows a long ignition delay time at a low temperature close to that of methane, but a short ignition delay time at a high temperature close to that of gasoline. In the present study, the antiknocking effect of adding methane with the RON of 120, ethane with the RON of 108, or propane with the RON of 112 to a regular gasoline surrogate fuel with the RON of 90.8 has been investigated. Adding each gaseous fuel by less than 0.4 in heat fraction advances knocking limit in the descending order of SI timing advance of ethane, methane, and propane, and in the descending order of CA 50 advance of ethane, propane, and methane. Adding methane extends combustion duration slightly, but adding ethane or propane shortens it considerably.

Next generation lubricating oils for transportation sector require higher durability in operation, compatibility with new engine technologies, aftertreatment devices and fuel economy (FE) characteristics, thus contributing to the reduction of CO2 emissions, both in passenger cars and heavy-duty vehicles. The current paper aims to highlight the impact of dispersant technologies for their main properties, that are preventing sludge and deposits formation on engine surfaces, and in regard to the effect on frictional properties of lubricating oils, through a multi-step activity. Oil contamination by soot is a big concern not only for diesel but also for new generation of direct injection gasoline (GDI) engines. The presence of soot leads to oil thickening that heavily impacts on friction coefficient thus enhancing the role of dispersant in controlling soot and related viscosity increase and, indirectly, fuel consumption for long running periods.

Light-duty vehicle emissions regulations worldwide impose stringent limits on particulate matter (PM) emissions, necessitating accurate modelling and prediction of particulate emissions across a range of sizes (as low as 10 nm). It has been shown that the decision tree-based ensemble machine learning technique known as Random Forest can accurately predict particle size, concentration, and accumulation mode geometric standard deviation (GSD) for 23 nm and greater diameter particulate emissions from a highly boosted gasoline direct injection (GDI) engine operating on a single fuel, while also offering insights into the underlying factors of emissions production because of the interpretable nature of decision trees. This work builds on this research as its basis and further investigates the relative performance of five decision tree-based machine learning techniques in predicting these particulate emission parameters and extends the work to 10 nm particles.

Inadequately designed flow field layouts in bipolar plates within Proton Exchange Membrane fuel cells (PEMFCs) may lead to ineffective water removal and impede reactant transport. This work examines the typical flow channel designs found in bipolar plates of fuel cells and implements modifications to certain designs to alleviate pressure drops within the flow channels using computational fluid dynamics (CFD) analysis. These designs are optimized by changing different parameters such as size of the channel and rib width utilizing Taguchi L27 standard orthogonal array. The resultant reduction in pressure drop is anticipated to enhance the overall performance of the fuel cell. The optimal flow field design of bipolar plates (Graphite and Aluminum) are manufactured using CNC milling. Tests evaluating flexural strength, surface roughness, hardness, contact angle, and corrosion resistance are conducted to assess and compare the performance of these plates.

The Reactivity Control Compression Ignition (RCCI) engine, with its dual fuel system and coordinated injection strategy, offers superior emission control and fuel efficiency compared to conventional diesel engines. However, cyclic variations leading to engine combustion instability poses a significant challenge to their development and commercialization. In this study, statistical (COV and Histogram) and nonlinear dynamic (Recurrence Plot and its Quantification) analysis techniques are applied on the time-series data obtained from a single-cylinder diesel engine modified to operate in CNG-Diesel RCCI mode. The engine, while advancing the main injection timing (SOI-2), is tested under various operating conditions, including different engine loads, direct injection mass ratios (DIMR) and port fuel injection (PFI) masses, to help identify the configurations with better temporal correlations and deterministic traits. Such configurations hold potential for control strategy implementation.

This work numerically investigated the methanol compression ignition combustion assisted with a glow plug (GP). The GP was positioned in the middle of the two intake ports. A heating power of 50 W was applied to maintain a quasi-steady temperature of 1323 K for the heating medium. Sensitivity analyses were conducted on various parameters affecting engine combustion characteristics and performance, including radial distance (RD) between the glow plug and injector, relative angle (RA) between the GP and its nearest jet, intake temperature, split ratio of pilot injection, and intake and injection pressures. Due to the complex fuel jet-GP interaction, the optimum RA shifted from 10° at RD = 22.5 mm to 17.5° at RD = 12.5 mm. The optimal RD among the studied values (12.5, 17.5, and 22.5 mm) was found to be 12.5 mm, achieving an indicated thermal efficiency (ITE) of 42.1% at RA = 17.5°.

High fuel stratification gasoline compression ignition (HFS-GCI) strategies allow for the use of ignition control methods similar to those used by diesel-fueled compression ignition (CI) engines while offering the emissions benefits of gasoline-like fuels. Despite this benefit, low load GCI operation requires ignition assistance viz. intake boosting, intake heating, cylinder deactivation, etc. for consistent autoignition. A novel ignition assistance methodology using an offset active prechamber (OAP) is proposed in this work to enable low load GCI operation. A 1.5cc OAP with a pressure-sensing spark plug and gaseous fuel injection system is designed and mounted in a medium-duty single-cylinder test engine based on the Cummins ISB engine. The prechamber is provided with two holes designed to ignite the fuel spray from the centrally mounted DI fuel injector. Gasoline was used as the main chamber fuel and methane was used as the prechamber fuel.

Combustion in conventional and advanced diesel engines is an intricate process that encompasses interaction among fuel injection, fuel-air mixing, combustion, heat transfer, and engine geometry. Manipulation of fuel injection strategies has been recognized as a promising approach for optimizing diesel engine combustion. Although numerous studies have investigated this topic, the underlying physics behind flame interactions from multiple fuel injections, spray-flame-wall interaction and their effects on reaction zones, and NOx/soot emissions are still not well understood. To this end, a computational fluid dynamics (CFD) study is performed to investigate the effects of pilot and post injections on in-cylinder combustion process and emissions (NOx and soot) formation in a heavy-duty (HD) diesel engine.

A comprehensive experimental study of hydrogen–diesel dual-fuel and hydrogen-hydrotreated vegetable oil (HVO) dual-fuel operations was conducted in a single-cylinder diesel engine (bore 85.0 mm, stroke 96.9 mm, and compression ratio 14.3) equipped with a common rail fuel injection system and a supercharger. The hydrogen flow rate was manipulated by varying the hydrogen excess air ratio from 2.5 to 4.0 in 0.5 increments. Hydrogen was introduced into the intake pipe using a gas injector. Diesel fuel and HVO were injected as pilot fuels at a fixed injection pressure of 80 MPa. The quantity of pilot fuel was set to 3, 6, and 13 mm3/cycle. The intake and exhaust pressures were set in the range of 100–220 kPa in 20 kPa increments. The engine was operated at a constant speed of 1,800 rpm under all conditions. The pilot injection timing was varied such that the ignition timing was constant at the TDC under all conditions.

High-efficiency lean-burn compression ignition using high-reactivity fuels, known as Gasoline Compression Ignition (GCI), demonstrates potential in reducing particulate matter (PM) and nitrogen oxide (NOx) emissions by controlling the charge ignition through both local strength and auto-ignition chemistry. This study explores the combustion strategy for GCI fuel with a Research Octane Number (RON) of 61 under a wide range of operating conditions using a Single Cylinder Research Engine (SCRE) calibrated to Euro 5 emission standards. The SCRE, with a compression ratio (CR) of 16.50, is designed for high-reactivity fuels and features a centrally located multi-hole injector and a piston bowl shape tailored to injection and spray characteristics. At steady state and part load (IMEP = 7 bar), the study investigates the impact of fuel injection strategy and the required amount of exhaust gas recirculation (EGR).

In the context of energy conservation and emission reduction, high power density(HPD) and low fuel consumption are the consistent pursuit of diesel engine development. Among the small-bore diesel, the limited space in the cylinder poses higher challenges and requirements for the arrangement of sprays.The high injection pressure results in a greater impulse when the spray impinges chamber, which allows the combustibles to develop along the chamber wall. Based on these characteristics of small-bore HPD diesel, a reasonable injection scheme is proposed to help flame diffusion surface increasing and thermal efficiency enhancing. This work proposes an optimization path to increase the flame diffusion surface, then improve thermal efficiency. It can be achieved with matching between the injector extension length and the spray spray angle.

With all the environmental concern of diesel fuelled vehicle, it is a formidable challenge to phase out them completely specifically from Heavy duty application. Most pragmatic solution lies in solutions which improves the fuel economy and reduce the carbon emission of existing diesel fuelled vehicle fleet and have economical & feasible for vast geographical extent of country. With implementation of BS VI emission norms across country from April 2020, supply of BS VI complied diesel fuel started and BS VI complied vehicles with upgraded engine technologies and after treatment devices have started to come which make present vehicle fleets heterogeneous with substantive number of BS IV vehicle. Beside improvement of engine technologies, existing BS IV vehicle fleet performance can be enhanced through improved fuel and lubricants solutions.

A reactivity-controlled compression ignition (RCCI) engine offers ultralow soot and nitrogen oxide (NOx) emission in addition to higher thermal efficiency than diesel or compression ignition (CI) engines. However, the higher emissions of unburned hydrocarbons (HC) and carbon monoxide (CO) from RCCI engines pose a significant challenge that hinders their adoption in the future automotive sector. Additionally, HC includes several hydrocarbons that harm human health and the environment. This study aims to minimize HC and CO formation and emissions by implementing different injection strategies, including adjustments to spray angle configuration, injection timing, and fuel premixing ratio. Additionally, the study examines how different injection strategies affect the spatial and temporal distribution of HC and CO inside the combustion chamber.

The development of new fuels for internal combustion engines requires further technical support by understanding the pollutant formation mechanism in various phases of combustion so that emissions can be minimized. This research will therefore utilize a bespoke in-cylinder sampling system to analyze the precursors of PAHs and particulates during bio-derived lactone combustion in a single-cylinder diesel engine. The sampling system was composed of a poppet-type in-cylinder sampling valve that displaced one of the engine intake valves and protruded into the combustion chamber beyond the flame quenching layer, and a Gas Chromatography Flame Ionization Detector (GC-FID) that examined the samples. The sampling valve was electromagnetically actuated, and its operation was referenced to the engine crank shaft encoder, allowing the valve to open at any Crank Angle Degree (CAD) within a timing resolution of 0.2 CAD.

The combustion of hydrogen (H2) as a fuel is attractive due to its clean combustion or combustion-enhancing properties when used as a supplement to other fuels. However, the challenge of using H2 as a fuel for transportation applications is the difficulty of onboard storage. Cracking onboard stored ammonia (NH3) into H2 can also improve combustion performance and emissions in mobile applications fuelled with zero and carbon-neutral fuels. However, the reforming process is not always 100 % efficient which can lead to the presence of NH3 in the combustion process. The presence of NH3 can influence engine performance, combustion and emissions. Therefore, this experimental study reports the effect of H2 and H2/NH3/N2 fuel blends added to gasoline in a dual-fuel operation under both stoichiometric (λ=1.0) and lean-burn (λ>1.0) operating conditions in a spark ignition (SI) engine.

As part of the European Green Deal, the EU has set itself the binding target of achieving climate neutrality by 2050 with the European Climate Act. At the same time, the EU is currently being confronted with an unprecedented energy crisis coupled with an increasing economic pressure, caused by military conflicts and geopolitical tensions resulting in increased fossil fuel prices. However due to high energy density liquid hydro-carbons are still critical needed fuels for transportation. On the other hand Biomass wastes, like sewage sludge and paper sludge, are currently a significant challenge to environmental protection. As a result due to nitrate pollution in soil, e.g. sewage sludge is no longer permissible to distribute on agricultural fields in a growing number of areas such as parts of Italy and Germany. Therefore there is currently a growing move towards the use of sewage sludge or paper sludge in thermal conversion processes.

The Advanced Fuel Ignition Delay Analyzer (AFIDA) apparatus can measure the ignition delay times with high repeatability within very short time. The device also requires small quantities of fuel samples. During AFIDA experiments, liquid fuel is injected into a hot and constant-volume chamber at high pressure. This way the ignition of the spray combines the effects of realistic influences like liquid evaporation and combustion chemistry. The present work investigates the effects of blending ethanol and 2,5-dimethylfuran with primary reference fuels (i.e., mixtures of iso-octane and n-heptane). The primary motivation of this study is to show the differences in ignition delay times of different gasoline-ethanol and gasoline-2,5-dimethylfuran blends where both physical mixing and chemical kinetics have considerable influences. The primary reference fuel is considered as the gasoline surrogate in this work. The study has been conducted at a range of temperatures and pressures.

Hydrogen as a chemical energy carrier is considered as one of the most promising options to achieve effective decarbonization of the transportation sector, due to its carbon-free chemical composition. This is particularly true for applications that rely on internal combustion engines (ICEs), although much research is still needed to achieve stable, reliable, and safe operations of the engine. To this purpose, direct injection (DI) of gaseous hydrogen during the compression stroke offers great potential to avoid backfire and largely reduce preignition issues, as opposed to port-fuel injection. Recently, much research has been dedicated, both experimentally and numerically, to understanding the physics and chemistry connected with hydrogen’s mixing and combustion processes in ICEs. This work presents a computational fluid dynamics (CFD) study of the hydrogen DI process in an optical engine operating at relatively low tumble conditions.