Search Results

Over the last decade, Climate change due to fossil fuel burning has taken centre stage in all discussions. Automotive sector has come under some flak for being one of the contributors to this Climate Change. Active steps have been taken by Vehicle Manufacturers and their Suppliers to address this issue. This sector has been facing below challenges to reduce pollutant in the air by A. Reducing Emissions, B. Increasing Energy Efficiency C. Use of Renewable Energy. One of the many alternatives by the Automotive Industry was to have a phased introduction to Electric Vehicles (EV), Hybrids, Fuel cells and other variants. As various emission norms and safety requirements takes Centre stage, it invariably, increases the weight of the vehicle. Now a days, Vehicles are having challenges to make it lightweight to achieve Range for an EV and improve fuel efficiency without sacrificing safety.

With the introduction of CAFÉ norms (Corporate Average Fuel Economy or Efficiency) in automobile industries, gasoline engines must improve their fuel economy by reducing overall CO2 footprints. To fulfil this demand many OEMs have adopted the use of exhaust gas circulation coolers (EGR) Most of the gasoline engines are having exhaust gas temperatures ranging from 650-850°C, these gases could also be highly corrosive in nature. It’s very important to select the right grade of stainless steel which should have high corrosion resistance and oxidation properties. It should also withstand high temperatures and should have low sensitization at high temperatures. Most of grades stainless steel offers high resistance against corrosion, high temperature properties. But good sensitization at high temperature is not always associated with all grades of steel. To compare corrosion resistivity, PREN number (Pitting Resistance Equivalent Number) plays important role.

Following Part 1 of the previous study, this paper reports the structure’s exciting force and summarize the overall research results. An experimental study was conducted to clarify the relationship between engine combustion and vibration, and to establish technology to suppress it. This study focused on the vehicle interior noise caused by combustion in which vibration transmission is the main component at high speed and high load region. A phenomenon in which both the combustion’s exciting force and the structure’s exciting force are combined is defined as vehicle interior noise caused by combustion. Conventionally, combustion and vibration are often discussed in terms of the average cycle, but considering the nonstationary property of vibration, in this paper analyzed the structure’s exciting force characteristics for vibration in cycle-by-cycle. Analysis was conducted using the combustion indicators clarified in the previous study.

A high compression ratio is an effective means for improving the thermal efficiency of an internal combustion engines. However, a high compression ratio leads to a rapid rise in the combustion pressure, as it causes a high impulse force. The impulse force generates vibrations and noise by spreading in the engine. Therefore, reducing the vibration of the combustion (which increases as the compression ratio increases) can improve the thermal efficiency while using the same technology. We are conducting model-based research on technologies for reducing combustion vibration by applying a granular damper to a piston. To efficiently reduce the vibration, we suppress it directly with the piston, i.e., the source of the vibration. Thus, the damping effect is maximized within a minimized countermeasure range.

Vehicle weight reduction is important to improve the fuel mileage of Internal Combustion Engine (ICE) vehicles and to extend the range of Electric Vehicles (EVs). Glass Fiber Reinforced (GFR) Composite (Polyamide) brackets provide significant weight reductions at a competitive part price. Traditionally, metal brackets are designed to surpass a target natural frequency and static stiffness. Composite brackets are inherently less stiff and have lower natural frequencies. However, composite brackets also have higher material damping than metal brackets, and good isolation performance can be achieved. The key to integrating composite brackets into the vehicle design is to perform adequate analysis to ensure that the noise and vibration performance at the vehicle level meets expectations. In this paper, case studies are presented for two different vehicles – a Clevis bracket for an IC Engine vehicle, and an electric motor mount bracket.

Light weight technologies are inevitable in the automotive industry to increase fuel efficiency and meet emission norms. An engine cylinder block is one of the major elements contributing approximately 3-4 % of the automobile weight. Aluminum cylinder block with cast-in liner is almost 40-55 % lighter than a conventional cast iron block [1] and hence the manufacturing processes and challenges associated with them are of high interest. A heterogeneous cast-in liner of gray cast iron in cast aluminum offers a low cost option, but the mechanical bond created between the liner and aluminum interface is prone to gap formation which affects the engine in terms of in-effective heat transfer, distortion and higher blow-by, and thereby high oil consumption & higher emissions. This study aims at reducing this interface bonding gap by in-depth study of critical process parameters involved in manufacturing of cylinder blocks.

This research evaluates the fuel economy and emissions of admixtures called gasoline multifunction additive (GMFA) and 10% ethanol blended gasoline against neat gasoline using newly developed Indian Motorcycle Driving Cycle with a BS VI motorcycle, also compared the performance of new cycle with the WMTC for the driving cycle parameters, fuel economy and emissions. The vehicles fuel economy and emissions factors are influenced by not only vehicle type, but also the road infrastructure and traffic patterns followed. The standard driving cycles do not replicate the real-world fuel economy and emissions as these cycles are very old and do not represent current traffic scenario. A real-world driving cycle was made based on micro-trips approach by analyzing the real-world time-speed data collected in four different pre-determined routes in Delhi-NCR region..

For realistic traffic modeling, real-world traffic calibration data is needed. These data include a representative road network, road users count by type, traffic lights information, infrastructure, etc. In most cases, this data is not readily available due to cost, time, and confidentiality constraints. Some open-source data are accessible and provide this information for specific geographical locations, however, it is often insufficient for realistic calibration. Moreover, the publicly available data may have errors, for example, the Open Street Maps (OSM) does not always correlate with physical roads. The scarcity, incompleteness, and inaccuracies of the data pose challenges to the realistic calibration of traffic models. Hence, in this study, we propose an approach based on spatial interpolation for addressing sparsity in vehicle count data that can augment existing data to make traffic model calibrations more accurate.

In order to sustain in automobile industry, fuel economy and robustness are playing vital role in vehicle. Every gram of weight will have an impact on fuel economy, thus burning a hole in consumers pocket and contributing heavily to the carbon footprint. Composite material development plays important role in meeting the stringent self-imposed targets of the automotive manufacturers and light weighting is becoming a prime option for improving Fuel Economy. The main objective of this paper is to optimize the weight of the luggage lid floor and reduce its cost without compromising on the strength by changing the raw material and manufacturing process. This part is in trunk compartment of the vehicle. Main function of this part is to withstand the luggage load under various user loading patterns at varied temperature and while driving on different road conditions.

Fatigue analysis of pistons is reliant on an accurate representation of the high temperatures to which they are exposed. It can be difficult to represent this accurately, because instrumented tests to validate piston thermal models typically include only measurements near the piston crown and there are many unknown backside heat transfer coefficients (HTCs). Previously, a methodology was proposed to aid in the estimation of HTCs for backside convection boundary conditions of a stratified charge compression ignition (SCCI) piston. This methodology relies on Bayesian inference of backside HTC using a co-simulation between computational fluid dynamics (CFD) and finite element analysis (FEA) solvers. Although this methodology primarily utilizes the more computationally efficient FEA model for the iterations in the calibration, this can still be a computationally expensive process.

In military applications, diesel engines are required to achieve high power outputs and therefore must operate at high loads. This high load operation leads to high piston component temperatures and heat rejection rates limiting the packaged power density of the powertrain. To help predict and understand these constraints, as well as their effects on performance, a thermodynamic engine model coupled to a finite element heat conduction solver is proposed and validated in this work. The finite element solver is used to calculate crank angle resolved, spatially averaged piston temperatures from in-cylinder heat transfer calculations. The calculated piston temperatures refine the heat transfer predictions as well requiring iteration between the thermodynamic model and finite element solver.

Low rolling resistance tires are a technology used to improve fuel economy and reduce greenhouse gas emissions in the transportation sector. This project analyzed current relationships between environmental and safety performance properties of commercially available light-duty tire models in Canada. This paper presents the results of a blinded multi-year light-duty vehicle tire research project conducted by Transport Canada & Natural Resources Canada. The study follows on an update to SAE WCX 2018-01-1336 which presented results for tires tested between MY2014-2018. Tire performance was evaluated in a variety of tire categories with a focus on wet grip and rolling resistance. Correlations between key performance indicators were charted to analyze trends in new model tires available on the Canadian tire market. Manufacturer specifications were also charted to evaluate the relations of wet grip and rolling resistance with price, UTQG ratings, and marketing categories.

The influence of early induction stroke direct injection on late-cycle flows was investigated for a lean-burn, high-tumble, gasoline engine. The engine features side-mounted injection and was operated at a moderate load (8.5 bar brake mean effective pressure) and engine speed (2000 revolutions per minute) condition representative of a significant portion of the duty cycle for a hybridized powertrain system. Thermodynamic engine tests were used to evaluate cam phasing, injection schedule, and ignition timing such that an optimal balance of acceptable fuel economy, combustion stability, and engine-out nitrogen oxide (NOx) emissions was achieved. A single cylinder of the 4-cylinder thermodynamic engine was outfitted with an endoscope that enabled direct imaging of the spark discharge and early flame development.

The fuel economy of the internal combustion engine becomes progressively critical, especially with the stringent standards set by the government. To meet the government norms such as CAFE (Corporate Fuel Average Economy), different technologies are being explored and implemented in internal combustion engines. Several technologies such as variable oil pump, map controlled PCJ (Piston Cooling Jet), variable or switchable water pump & ball bearing turbocharger etc. This study investigates the effectiveness of implementing map-controlled PCJ implemented for a 1.5-litre 3-cylinder diesel engine. PCJ’s are major consumers of oil flow and map-controlled PCJ is used by many OEM’s e.g., Ford EcoSport to reduce the oil pump flow. In map-controlled PCJ, the oil to the PCJ is controlled using a solenoid valve. The solenoid valve can be completely variable or ON/OFF type. In our application, the ON/OFF type solenoid value is used to regulate the oil flow to PCJ.

This study aims to improve the dual fuel combustion for low/zero carbon fuels. Seven cases were tested in a single cylinder optical engine and their ignition and combustion characteristics are compared. The baseline case is the conventional diesel combustion. Four cases are diesel-gas (compressed natural gas) dual-fuel combustion operations, and two cases are diesel-hythane combustion. The diesel fuel injection process was visualized by a high-speed copper vapour laser. The combustion processes were recorded with a high-speed camera at 10000 Hz with an engine speed of 1200 rpm. The high-speed recordings for each case included 22 engine cycles and were postprocessed to create one spatial overlapped average combustion image. The average combustion cycle images were then further thresholded and these images were then used in a new method to analyze the cycle-to-cycle variation in a dimensionless, for all cases comparable value.

To meet the target of the CO2 regulations, it is mandatory to replace high-carbon fossil fuels with low-carbon fuels. Diesel/Natural Gas (NG) reactivity-controlled compression ignition (RCCI) can reduce CO2 emission, which stratifies two types of fuels with different reactivity. And also, RCCI produces less NOx and particulate matter emissions by reducing the in-cylinder temperature. However, RCCI must still be enhanced in terms of the thermal and combustion efficiencies at low and medium loads. In this work, a modified piston geometry was applied to improve the RCCI combustion. The piston geometry was designed to minimize heat loss and reduce flame quenching in an RCCI engine. Experiments were conducted using a single-cylinder engine with a displacement volume of 1,000 cc. Diesel was directly injected into the cylinder, and NG was fed through the intake port.

A multiple-injection combustion strategy has been developed for heated gasoline direct injection compression ignition (HGCI). Gasoline was injected into a 0.4L single cylinder engine at a fuel pressure of 300bar. Fuel temperature was increased from 25degC to a temperature of 280degC by means of electric injector heater. This approach has the potential of improving fuel efficiency, reducing harmful CO and UHC as well as particulate emissions, and reducing pressure rise rates. Moreover, the approach has the potential of reducing fuel system cost compared to high pressure (>500bar) gasoline direct injection fuel systems available in the market for GDI SI engines that are used to reduce particulate matter. In this study, a multiple injection strategy was developed using electric heating of the fuel prior to direct fuel injection at engine speed of 1500rpm and load of 12.3bar IMEP.

A PPCI-diffusion combustion strategy has shown the potential to achieve high efficiency, clean gasoline compression ignition (GCI) combustion across the full engine operating range. By conducting a 3-D CFD-led combustion system design campaign, this investigation was focused on developing a next generation (NextGen), step-lipped piston design concept in a 2.6L advanced light-duty GCI engine. Key geometric features of the NextGen piston bowl were parametrized and studied with customized spray targeting. A low lip positioning design with 128° spray targeting was found to provide the best performance. Fuel injection strategy optimization was performed at a full-load operating point (OP), 2000 rpm/24 bar closed-cycle IMEP (IMEPcc).

Prior work in the literature have shown that pre-chamber spark plug technologies can provide remarkable improvements in engine performance. In this work, three passively fueled pre-chamber spark plugs with different pre-chamber geometries were investigated using in-cylinder high-speed imaging of spectral emission in the visible wavelength region in a single-cylinder direct-injection spark-ignition gasoline engine. The effects of the pre-chamber spark plugs on flame development were analyzed by comparing the flame progress between the pre-chamber spark plugs and with the results from a conventional spark plug. The engine was operated at fixed conditions (relevant to federal test procedures) with a constant speed of 1500 revolutions per minute with a coolant temperature of 90 oC and stoichiometric fuel-to-air ratio. The in-cylinder images were captured with a color high-speed camera through an optical insert in the piston crown.

The major area in which the automotive manufacturers are working is to produce high-performance vehicles with lighter weight, higher fuel economy and lower emissions. In this regard, hollow camshafts are widely used in modern diesel and gasoline engines due to their inherent advantages of less rotational inertia, less friction, less weight and better design flexibility. However, the dynamic loads of chain system, valve train and fuel injection pump (if applicable) makes it challenging to design over-head hollow camshafts with the required factor of safety (FOS). In the present work, high-fidelity FE model of a hollow camshaft assembly is simulated to evaluate the structural performance for assembly loads, valve train operating loads, fuel injection pump loads and chain system loads. The investigation is carried out in a high power-density (70 kW/lit) 4-cylinder in-line diesel engine.