Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Optimization of vehicle side panel to improve crashworthiness.

2019-11-21
2019-28-2573
The front of a car, though susceptible to the biggest impacts in terms of magnitude, has space and additional reinforcement to incorporate various safety measures. The rear has considerable amount of space to contain a proper crash box. The side of the car, though, doesn’t have this flexibility in design, the main limiting parameter being space. Any intrusion into the passenger cabin can result in serious injury or even death. The objective of this work is to improve the crashworthiness of a vehicle’s side so as to reduce intrusion into the passenger cabin. The work is focused on optimizing the door and B pillar. The optimized side panel is compared with the baseline model as per standard. ANSYS solver is used for the simulation. The optimized design applied to the door and B pillar will significantly improve crashworthiness of the vehicle side panel as a whole.
Technical Paper

Transient Response Analysis and Synthesis of an FSAE Vehicle using Cornering Compliance

2019-11-21
2019-28-2400
OBJECTIVE Race vehicles are designed to achieve higher lateral acceleration arising at cornering conditions. A focused study on the steady state handling of the car is essential for the analysis of such conditions. The transient response analysis of the car is also equally important to achieve best driver-car relationship and to quantify handling in the range suitable for a racing car. This research aims to investigate the design parameters responsible for the transient characteristics and optimize those design parameters. This research work examines the time-based analysis of the problem to truly capture the non-linear dynamics. Apart from tires, chassis can be tuned to optimize vehicle handling and hence the response times. METHODOLOGY To start with, the system is modelled with governing parameters and simulation is carried out to set baseline configurations. Steady state and transient handling simulations run independent of each other with independent logic, coded on MATLAB.
Technical Paper

Design improvements in advanced automotive batteries using AI

2019-11-21
2019-28-2505
Introduction: The advent of electric mobility is changing the conventional mobility techniques and with this comes challenges to improve the performance of battery to optimize power consumption in electric vehicles. Objective: This paper would focus on the optimization of battery performance incoherent with vehicle power consumption behavior in terms of efficiency using decision-making ability based on given input signals
Technical Paper

Enhancement of safety features of steering wheel using experimentally validated finite element model

2019-11-21
2019-28-2556
Automotive safety is the primary concern in the current world. In order to develop safe and crashworthy vehicles, phenomena behind the energy absorption characteristics of every automotive component must be known. Steering wheel is one of the key players which could cause severe injuries to the driver if sufficient safety measures are not considered. This research focuses on the crash performance of commercial vehicle steering as per head form and body block test prescribed in ECE R12. Detailed FE (Finite Element) model of the steering wheel including armature, horn pad was developed using nonlinear material properties. The model was first validated using the test results. Comparisons between experimental results and finite element analysis results were conducted and correlated using load versus displacement profiles over the duration of impact. A good relationship between test and FE results was found which allows for investigation into the energy analysis of the steering components.
Technical Paper

Photo oxidation analysis method for automotive coating weathering performance evaluation

2019-11-21
2019-28-2555
RESEARCH OBJECTIVE Accelerated artificial weathering performance has been always observed as critical and most important factor for durability prediction of colour and resin for a coating system. Photo oxidation of resin is the phenomenon behind coating’s ageing. Though accelerated weathering tests protocols are widely used in industry, they are very costly and still very time consuming. One automotive grade accelerated testing can go as long as 8 months duration. METHODOLOGY (maximum 150 words) Photo oxidation value (POV) is proportionate to the degradation of the resin material used in coating. During the accelerated weathering POV is measured for the coating at stipulated interval during initial phase and trend is plotted for deterioration verses weathering test duration. POV can be analysed with the help of FTIR analysis to observe bond absorption energy and bond separation energy in the resin system. This trend can be extrapolated to predict the weathering performance of coating.
Technical Paper

IMPROVE NVH CHARACTERISTICS OF ENGINE OIL PAN BY OPTIMIZATION & LIGHT WEIGHING WITH DEEP LEARNING PROCESS

2019-11-21
2019-28-2552
Recent Years “NVH” is gaining lots of attention as the perception of vehicle quality by a consumer is closely aligned to NVH Characteristics. Demand on Vehicle Light weighting to compliance the environmental norms with powerful engines challenging the “Vehicle NVH”, powertrain induced noise will be continued to be a primary factor for all IC engine vehicles. Component level NVH refinement is necessary to control the overall NVH characteristics of vehicle with lighter Vehicle goal. Current Paper works starts with physical testing the Engine oil pan of the most popular vehicle and build an equivalent simulation model by reverse engineering the design and match similar performance trend in simulation model. After building baseline simulation model, conduct shape, topology, gauge and material optimization to improve weight and performance of Oilpan.
Technical Paper

Analysis of occupant dynamics and optimization of Driver airbag performance against all FMVSS208 frontal impact cases using validated Finite element Methodology

2019-11-21
2019-28-2545
Several people die every year due to vehicle accidents. Federal Motor Vehicle Safety Standards (FMVSS) are U.S. federal regulations stating design, structure, performance, and durability necessities for vehicles. The objective of a crash test for FMVSS No. 208 is to measure how well a passenger vehicle would protect its occupants in the event of a frontal crash. FMVSS 208 consists of series of tests including different impact surface type as well as occupant sizes. It also covers the belted and unbelted occupant behavior at the time of front impact. Each test scenario has different ways to injure the occupant. Airbags are the part of passive safety equipment family in any automobile and play an imperative role to reduce the occupant head and chest injuries at the time of crash or accidents. This study covers the evaluation of airbag performance in all FMVSS 208 load cases using validated Finite Element Methodology (FEM).
Technical Paper

Wiring Harness Optimization towards Wireless Vehicle

2019-11-21
2019-28-2530
Paper Title - Wiring Harness Optimization towards Wireless vehicle Research and/or Engineering Questions/Objective (maximum 100 words)  In current scenario, wiring harness plays a vital role in inter-connecting electrical & electronic components fitted all across the vehicle.  As per cable standard, DIN 72551 or ISO 6722, copper conductors being used in stranded wires against cable cross-section & corresponding weight.  While going complete wire-less requires each component to have its own battery, ground, transmitter & receiver which indeed is a very costly affair to be employed in vehicle as huge development cost is required.  Here I'm suggesting an innovative method to make a vehicle apparently Wire-Less by creating local clusters connected to each other via conventional wiring harness & wire-less module.  Such method will apparently give a look of Wire-less vehicle itself & better advantages in terms of installation, service, troubleshooting, uptime & customer delight.  Moreover, direct benefits of Cost, Weight, FE will also be achieved.
Technical Paper

Passenger "Sleeper Bus" Structure, an Optimization Study using Finite Element Analysis

2019-11-21
2019-28-2537
Sleeper buses are increasingly used as connectivity between cities and remote areas with sleeping comfort for passengers. During the normal operation, the bus body is subjected to several loads, external loads from the road (i.e. crossing over a speed bump, breaking & cornering). Moreover, there is a substantial possibility that these loads may lead to a structural failure. Hence, it is necessary to determine stresses occurred in the bus body to ensure its integrity under these driving scenarios. During the accident, rollover/front/rear/side impact, energy absorbing capacity of bus body structure is crucial for safety of passengers. The objective of this study is to reduce weight of bus structure while maintaining cost & safety as constraint. 3D Model prepared in NX and finite element model created in hypermesh ,LS-dyna/optistruct used as solver and post processing done in hyperview. In this study, fully loaded bus with passengers as well as maximum language mass, considered.
Technical Paper

Miniaturized and sleek protective device

2019-11-21
2019-28-2535
A miniaturized and sleek protective device M. Priyanka, Mahindra&Mahindra, India D. Boobala Krishnan*, Mahindra&Mahindra, India T.Vijayan, Mahindra& Mahindra, India Keywords-Fuse, Lightweight. Research and/or Engineering Questions/Objective: Now-a-days there is lot of advancement coming in automobiles. Earlier the electronics were used in engine and engine compartment areas. Now all hydraulics and transmission have been operated by electronics. The role of electronics like sensors, actuators increasing day by day for lifting and moving operations. With increase in electronics circuit, there is complex in wiring harness and packaging space for fuse box is premium Limitations: Limitations of placing other devices. Occupy more space and weight in the vehicle. Packing constraint due to vibration and thermal management issues. Methodology: Two different fuse of same rating can be given in one fuse and we can reduce the wire size.
Technical Paper

Development of Electric Vehicle Controller by using MBD approach

2019-11-21
2019-28-2494
The automobile industry is moving towards electrification of Vehicle to remove the exhaust gas emissions. A project was undertaken to develop Electric Vehicle control system from concept to vehicle trials in less than a year. The complete development cycle of an electronic controller required to be compressed to prepare mule electric vehicle within timeline. Agile methodology has been used for this project instead of waterfall as other control systems were in developing stage; system requirements were changing frequently. This paper presents the electric vehicle control unit development with agile methodology using model based development (MBD) in MATLAB and Simulink environment. The project flow consists of major phases like design of electrical architecture, system requirements specification, selection and setting up the simulation platform, EVCU strategy development, testing on Model in Loop (MIL)/ Hardware in Loop (HIL), vehicle trials.
Technical Paper

Powertrain topologies for 2 wheelers : From ICE to Electrification

2019-11-21
2019-28-2480
As Battery cost is expected to see a Downward trend, Electrification of Powertrain in general is expected to pick up and 2wheeler Market is foreseen to be the Flag bearer in this race towards Electrification. In this paper, we would like to emphasize on the Journey of 2wheelers from Conventional Internal combustion Engine to Electrified Powertrains which we foresee in the future. Methodology: EV - Analysis of OEM strategies and upcoming trends in connectivity and electrification. Estimation of current market size of 2Wheeler and segmentation based on different personas. Building survey data based personas around ownership patterns for electric 2Wheelers. Mapping consumer decision process for electric 2Wheelers. Analyse the decision influencers and role of influencers in decision making process. Hybrid - Analysis of different hybrid topologies. Feasibility study via simulation and focus group assessments to evaluate the design. PoC will also be tried to validate the concept.
Technical Paper

Non-linear dynamic Modeling, Simulation and Control of Five-Phase 10/8 Switched Reluctance Motor for Electric Vehicle Application

2019-11-21
2019-28-2473
The SRM is gaining much interest for EVs due to its rare-earth-free characteristic and excellent performance. SRM possess several advantages such as low cost, high efficiency, high power density, fault-tolerant and it can produce extended constant power region, and this makes SRM as viable alternative over conventional PM drives. Objective: The objective of this paper is to establish proof of theoretical concepts related to SRM. The key to achieve an effective SRM modeling is to use a methodology that allow the nonlinearity of its magnetic characteristics to be represented while maximizing the simulation speed. This paper represents how magnetization data obtained from FEA in the form of look up tables is most appropriate way to represent SRM model. In this paper, performance analysis of SRM is done with the help of Open loop and Closed loop MATLAB simulations. These dynamic simulations of SRM will assist in understanding behavior of SRM in various loading and speed conditions.
Technical Paper

Automobile Exhaust Emmision Control- A review

2019-11-21
2019-28-2382
Since the 20th century increase in the number of cars in the major cities is been a point of concern because of the toxic gasses being emitted from the engine of an automobile. These gasses are polluting the atmosphere and degrading the air to breathe. The main gasses responsible for the degradation of air quality are carbon monoxide, hydrocarbon and oxides of nitrogen. There is a necessity to find ways to reduce the pollution emitted into the atmosphere from the automobile. The source of emission is either evaporation from fuel tank or carburetor which is easy to be dealt with or harmful gasses due to improper combustion which is a concern for the environment. The two ways to reduce these emissions are, modification in the engine to minimize the production of harmful gases and to treat the harmful gasses emitted from the engine before blowing it into the atmosphere from the exhaust. Catalysts help to break harmful gasses into smaller compounds that are environment-friendly.
Technical Paper

Aerodynamic Analysis of a Passenger Car to Reduce Drag Using Active Grill Shutter and Active Air Dam

2019-11-21
2019-28-2408
Active aerodynamics can be defined as the concept of reducing drag by making real-time changes to certain devices such that it modifies the airflow around a vehicle. Using such devices also have the added advantages of improving ergonomics and performance along with aesthetics. A significant reduction in fuel consumption can also be seen when using such devices. The objective of this work is to reduce drag acting on a passenger car using the concept of active aerodynamics with grill shutters and air dams. First, analysis has been carried out on a baseline passenger car and further simulated using active grill shutters and air dams for vehicle speed ranging from 60 kmph to 120 kmph, with each active device open from 0° to 90°. The optimized model is then validated for a scaled-down prototype in a wind tunnel at 80kmph. Vehicle has been modelled using SolidWorks and the simulation has been carried out using ANSYS Fluent.
Technical Paper

Design of Additive Manufactured Thermoplastic Component as FMVSS 201U Countermeasure

2019-11-21
2019-28-2547
Research and/or Engineering Questing/Objectives: Safety of the occupant in passenger cars is one of the regulatory requirements in many developed countries. This includes upper interior head impact load case of the unbelted occupant during crash (FMVSS 201U) as one of them. During a crash event the occupant head can collide with the interior parts of the vehicle, such as a headliner, pillar trim and other subsequent components in the loading direction. Injury on the head is quantified in terms of the Head Injury Criterion of a crash test dummy (HIC(d)) value which should be less than 1000 per standard. Several ways can be adopted to reduce the HIC(d) value. These include a change in the design of ribs in the safety plastic components, headliner profile change, use of countermeasure foam between headliner and the exterior sheet metal parts, or a combination of any of these to absorb the energy of impact.
Technical Paper

SELF EXPRESSIVE & SELF HEALING CLOSURES HARDWARES FOR AUTONOMOUS AND SHARED MOBILITY

2019-11-21
2019-28-2525
Shared Mobility is changing the trends in Automotive Industry and its one of the Disruptions. The current vehicle customer usage and life of components are designed majorly for personal vehicle and with factors that comprehend usage of shared vehicles. The usage pattern for customer differ between personal vehicle, shared vehicle & Taxi. In the era of Autonomous and Shared mobility systems, the customer usage and expectation is high. The vehicle needs systems that will control customer interactions (Self-Expressive) & fix the issues on their own (Self-Healing). These two systems / methods will help in increasing customer satisfaction and life of the vehicle. We will be focusing on vehicle Closure hardware & mechanisms and look for opportunities to improve product life and customer experience in ride share and shared mobility vehicles by enabling integrated designs, which will Self-Express & Self-Heal.
Technical Paper

LIGHT WEIGHTING OF ADDITIVE MANUFACTURED PARTS FOR AUTOMOTIVE PRODUCTION APPLICATIONS THROUGH TOPOLOGY OPTIMIZATION TECHNIQUES

2019-11-21
2019-28-2544
Rapidly enhancing engineering techniques to manufacture components in quick turnaround time have gained importance in recent time. Manufacturing strategies like Additive Manufacturing (AM) are a key enabler for achieving them. Unlike traditional manufacturing techniques such as injection molding, casting etc., AM unites advanced materials, machines, and software which will be critical for Industry 4.0. Successful application of AM involves a specific combination and understanding of these three key elements. In this paper the AM approach used is Fused Deposition Modelling (FDM). Since material costs contribute to 60% of the overall FDM costs, it becomes a necessity to optimize the material consumption of the produced parts. This paper reports case studies of 3D printed parts used in an Automobile plant’s production aids, which utilize computational methods(CAE), topology optimization and FDM constrains (build directions) to manufacture the part in the most optimal way.
Technical Paper

SIMULATION OF SOFTENING AND RUPTURE IN MULTILAYERED FUEL TANK MATERIAL

2019-11-21
2019-28-2557
Research and/or Engineering Questions/Objective Plastic automotive fuel tanks made up of blow molded, multi-layered, high-density polyethylene (HDPE) material can take complex shapes with varying thickness. Accidental drop of fuel tank from a height during handling can lead to development of cracks. Damage can also occur due to an impact during a crash. This can be catastrophic due to flammability of the fuel. The objective of this work is to characterize and develop a failure model for the fuel tank material to simulate damage and enhance predictive capability of CAE for chassis and safety load cases. Methodology Different aspects were considered to develop a characterization and modelling strategy for the HDPE fuel tank. Material properties can be influenced by factors such as, service temperature, rate of deformation, state of stress etc.
Technical Paper

Electrification System Modeling with Machine/Deep Learning for Virtual Drive Quality Prediction

2019-11-21
2019-28-2418
A virtual 'model' is generally a mathematical surrogate of a physical system and when well correlated, serves as a basis for understanding the physical system in part or in entirety. Drive Quality defines a driver's 'experience' of a blend of controlled responses to an applied input. The 'experience' encompasses physical, biological and bio-chemical perception of vehicular motion by the human body. In the automotive domain, many physical modeling tools are used to model the sub-components and its integration at the system level. Physical Modeling requires high domain expertise and is not only time consuming but is also very 'compute-resource' intensive. In the path to achieving 'vDQP (Virtual Drive Quality Prediction)' goal, one of the requirements is to establish 'well-correlated' virtual environments of high fidelity with respect to standard test maneuvers. This helps in advancing many developmental activities from a Controls and Calibration aspect.
X