Search Results

An investigation was performed to identify the benefits of cooled exhaust gas recirculation (EGR) when applied to a potential ethanol flexible fuelled vehicle (eFFV) engine. The fuels investigated in this study represented the range a flex-fuel engine may be exposed to in the United States; from 85% ethanol/gasoline blend (E85) to regular gasoline. The test engine was a 2.0-L in-line 4 cylinder that was turbocharged and port fuel injected (PFI). Ethanol blended fuels, including E85, have a higher octane rating and produce lower exhaust temperatures compared to gasoline. EGR has also been shown to decrease engine knock tendency and decrease exhaust temperatures. A natural progression was to take advantage of the superior combustion characteristics of E85 (i.e. increase compression ratio), and then employ EGR to maintain performance with gasoline. When EGR alone could not provide the necessary knock margin, hydrogen (H2) was added to simulate an onboard fuel reformer.

The use of high levels of EGR has been documented to increase fuel efficiency and reduce emissions of spark ignition engines [1–5]. However, these engines typically face challenges in EGR control and tolerance, which can reduce the expected efficiency improvement. A concept developed by Southwest Research Institute explores the potential of an engine with individual cylinders dedicated to EGR production to overcome the challenges associated with EGR tolerance and control. In this study, a 4-cylinder engine was run with cylinder 1 exhausting directly to the intake manifold, leading to a constant 25% EGR level. The engine was run naturally aspirated over a large portion of the performance map at an ultra-high (14:1) compression ratio. As a part of the study, air-to-fuel ratio in cylinder 1 was varied from stoichiometric to rich to determine the effect of the products of partial combustion on EGR tolerance and fuel consumption.

A gasoline direct injection engine was operated at elevated EGR levels over a significant portion of the performance map. The engine was modified to use both cooled and un-cooled EGR in high pressure loop and low pressure loop configurations. The addition of EGR at low and part load was shown to decrease NO and CO emissions and to reduce fuel consumption by up to 4%, primarily through the reduction in pumping losses. At high loads, the addition of EGR resulted in higher fuel consumption benefits of 10-20% as well as the expected NO and CO reductions. The fuel economy benefit at high loads resulted from a decrease in knock tendency and a subsequent improvement in combustion phasing as well as reductions in exhaust temperatures that eliminated the requirement for over-fuelling.

Small (up to 1% by volume) amounts of hydrogen (H2) were added to the intake charge of a single-cylinder, stoichiometric spark ignited engine to determine the effect of H2 addition on EGR tolerance. Two types of tests were performed at 1500 rpm, two loads (3.1 bar and 5.5 bar IMEP), two compression ratios (11:1 and 14:1) and with two fuels (gasoline and natural gas). The first test involved holding EGR level constant and increasing the H2 concentration. The EGR level of the engine was increased until the CoV of IMEP was > 5% and then small amounts of hydrogen were added until the total was 1% by volume. The effect of increasing the amount of H2 on engine stability was measured along with combustion parameters and engine emissions. The results showed that only a very small amount of H2 was necessary to stabilize the engine. At amounts past that level, increasing the level of H2 had no or only a very small effect.

Tests were conducted on a variety of commercially available spark plugs to determine the influence of igniter design on initial kernel formation and overall performance. Flame kernel formation was investigated using high-speed schlieren visualization. The flame growth rate was quantified using the area of the burned gas region. The results showed that kernel growth rate was heavily influenced by electrode geometry and configuration. The igniters were also tested in a bomb calorimeter to determine the levels of supplied and delivered energy. The typical ratio of supplied to delivered energy was 20% and igniters with a higher internal resistance delivered more energy and had faster kernel formation rates. The exception was plugs with large amounts of conductive mass near the electrodes, which had very slow kernel formation rates despite relatively high delivered energy levels.

A series of tests using an open beam laser ignition system in an engine run on pre-mixed, gaseous fuels were performed. The ignition system for the engine was a 1064 nm Nd:YAG laser. A single cylinder research engine was run on pre-mixed iso-butane and propane to determine the lean limit of the engine using laser ignition. In addition, the effect of varying the energy density of the ignition kernel was investigated by changing the focal volume and by varying laser energy. The results indicate that for a fixed focal volume, there is a threshold beyond which increasing the energy density [kJ/m3] yields little or no benefit. In contrast, increasing the energy density by reducing the focal volume size decreases lean performance once the focal volume is reduced past a certain point. The effect of ignition location relative to different surfaces in the engine was also investigated. The results show a slight bias in favor of igniting closer to a surface with low thermal conductivity.

Swirl plane Particle Image Velocimetry (PIV) measurements were performed in a single-cylinder optically accessible gasoline direct injection (DISI) engine using a borescope introduced through the spark plug hole. This allowed the use of a contoured piston and the visualization of the flow field in and around the piston bowl. The manifold absolute pressure (MAP) was fixed at 90 kPa and the engine speed was varied in increments of 250 rpm from 750 rpm to 2000 rpm. Images were taken from 270° to 320° bTDC of compression at 10° intervals to study the evolution of the velocity fluctuations. Measurements were performed with and without fuel injection to study its effect on the in-cylinder flow fields. Fuel was injected at 10 MPa and 5 MPa. The 2-D spatial mean velocities of individual flow fields and their decompositions were averaged over 100 cycles and used to investigate the effects of engine speed and image timing on the flow field.

SwRI has developed a new technology concept involving the use of high EGR rates coupled with a high-energy ignition system in a gasoline engine to improve fuel economy and emissions. Based on a single-cylinder study [1], this study extends the concept of a high compression ratio gasoline engine with EGR rates > 30% and a high-energy ignition system to a multi-cylinder engine. A 2000 MY Isuzu Duramax 6.6 L 8-cylinder engine was converted to run on gasoline with a diesel pilot ignition system. The engine was run at two compression ratios, 17.5:1 and 12.5:1 and with two different EGR systems - a low-pressure loop and a high pressure loop. A high cetane number (CN) diesel fuel (CN=76) was used as the ignition source and two different octane number (ON) gasolines were investigated - a pump grade 91 ON ((R+M)/2) and a 103 ON ((R+M)/2) racing fuel.

Particle Image Velocimetry (PIV) experiments were performed on single-cylinder versions of a 0.375 L/cylinder and a 0.5 L/cylinder engines from the same engine class to determine the differences in swirl flow between the two engines. Two engine speeds (750 and 1500 rpm), manifold pressures (75 kPa and 90 kPa) and valve timings (maximum overlap and with the intake valve 20° retarded from the max overlap position) were examined. The swirl ratio (SR) and mean velocity (|V|) were calculated at BDC for every case in the mid-stroke plane and the fluctuation velocity (U') calculated for the 1500 rpm / 90 kPa / maximum overlap case. The in-cylinder velocities do not differ by the expected ratio of mean piston speed caused by differences in the engine stroke. The smaller engine was expected to have lower in-cylinder velocities and SRs due to a shorter stroke and lower piston speeds but instead has SR and |V| levels that are the same or higher than the larger engine.

A PLIF measurement system was designed and applied for imaging direct-injected stratified charge fuel preparation. An extensive measurement plane was achieved through novel design features in the system. Measurement and processing uncertainties were assessed at ±15% for the semi-quantitative fuel density. Tracer selection among suggested iso-octane candidates was found not to have a significant effect on PLIF results under the conditions tested. Stratified charge fuel distribution images were acquired for three piston and fuel injector combinations. The effect of piston design in guiding the fuel mixture position was most notable. Fuel distribution features correlated reasonably well with measured data from a thermodynamic engine of similar design.

The influence of mixture preparation on misfires at idle in a Direct Injection Spark Ignition (DISI) engine was investigated. A wall-guided DISI engine was run at idle conditions in a stratified charge mode (750 rpm / 90 kPa MAP). Images of the mixture composition at the spark plug were taken at spark timing using Planar Laser Induced Fluorescence (PLIF) for several different End-of-Injection (EOI) timings and spark timings. Cylinder pressure data were acquired simultaneously with the images to identify misfire cycles. The misfire rate was found to increase as the EOI timing was advanced from the optimal timing, defined by maximum stability and lowest ISFC. Images show that the misfire rate at a particular operating condition can be correlated to the fuel distribution and the location of the stratified charge in the engine. Cycles that showed a lower amount of stratification (overmixing) and/or high gradients in fuel concentration near the spark plug were the least stable.

A new Light Stratified-Charge Direct Injection (LSC DI) spark ignition combustion system concept was developed at Ford. One of the new features of the LSC DI concept is to use a ‘light’ stratified-charge operation window ranging from the idle operation to low speed and low load. A dual independent variable cam timing (DiVCT) mechanism is used to increase the internal dilution for emissions control and to improve engine thermal efficiency. The LSC DI concept allows a large relaxation in the requirement for the lean after-treatment system, but still enables significant fuel economy gains over the PFI base design, delivering high technology value to the customer. In addition, the reduced stratified-charge window permits a simple, shallow piston bowl design that not only benefits engine wide-open throttle performance, but also reduces design compromises due to compression ratio, DiVCT range and piston bowl shape constraints.

A spontaneous Raman scattering diagnostic was used to measure the residual fraction in a single-cylinder, 4-valve optically accessible engine. The engine was operated at 1500 rpm on pre-vaporized iso-octane at several intake manifold pressures (50-90 kPa). Cam phasing was varied to determine the effect of intake valve timing and valve overlap on the residual mass fraction of the engine. A simple model based on the ideal Otto cycle and 1D gas flow through the exhaust valves was proposed to analyze the results of the Raman experiment. The model showed good agreement (R2=0.91) with the experimental results and demonstrated its potential for use as a method to estimate the residual fraction in an engine from available dynamometer data. The experimental results showed that the residual fraction was reduced at higher manifold pressures due to less backflow through the exhaust valves and varied with intake cam phasing.

Particle Image Velocimetry (PIV) measurements were performed on a single cylinder optically accesible version of a 3.0L 4-valve engine using a Camshaft Profile Switching (CPS) system. The flow field was investigated at two engine speeds (750 and 1500 rpm), two manifold pressures (75 and 90 kPa) and two intake cam centerlines (maximum lift at 95° and 115° aTDCi respectively). Images were taken in the swirl plane at 10 mm and 40 mm below the deck with the piston at 300° aTDC of intake (60° bTDC compression) and BDC respectively. In the tumble plane, images were taken in a plane bisecting the intake valves with the piston at BDC and 300° aTDC. The results showed that the swirl ratio was slightly lower for this system compared with a SCV system (swirl control valve in the intake port) under the same operating conditions. The swirl and tumble ratios generated were not constant over the range of engine speeds and manifold pressures (MAP) but instead increased with engine speed and MAP.

Piston wetting can be isolated from the other sources of HC emissions from DISI engines by operating the engine predominantly on a gaseous fuel and using an injector probe to impact a small amount of liquid fuel on the piston top. This results in a marked increase in HC emissions. All of our prior tests with the injector probe used California Phase 2 reformulated gasoline as the liquid fuel. In the present study, a variety of pure liquid hydrocarbon fuels are used to examine the influence of fuel volatility and structure. Additionally, the exhaust hydrocarbons are speciated to differentiate between the emissions resulting from the gaseous fuel and those resulting from the liquid fuel. It is shown that the HC emissions correspond to the Leidenfrost effect: fuels with very low boiling points yield high HCs and those with a boiling point near or above the piston temperature produce much lower HCs.