Search Results

Powertrain complexity rapidly increasing to meet fast moving regulation requirements. The BS6 Phase-1 regulation norms were implemented in India from April 1, 2020 and replaced the previous BS4 norms. Phase-2 of the BS6 regulation norms were came into effect on April 1, 2023. To meet this stringent regulation requirement, need effective performance of after treatment systems like DOC, DPF and SCR demands critical hardware selection and implementation. A robust DeNOx emissions strategy is developed in naturally aspirated single cylinder LCV application to meet cycle emissions, real drive emissions and OBD requirements. Naturally aspirated single cylinder engine has its own challenges to meet BS6 norms like higher engine out NOx, dynamic temperature profiles etc. It is always a challenge to adapt EATS in LCV application as these are low-cost vehicles. EATS components and sensors impacts the overall cost of the vehicle.

With the increasing focus on reducing CO2 emissions to combat global warming and climate change, the automotive industry is exploring near zero-emission alternative fuels to replace traditional fossil-based fuels like diesel, gasoline, and CNG. Methanol is a promising alternative fuel that is being evaluated in India due to its easy transportation and storage, as well as its production scalability and availability potential. This study focuses on the retro-fitment solution of M100 (pure methanol) SI port-fuel injection (PFI) mode of combustion. A heavy duty single-cylinder engine test setup was used to assess methanol SI combustion characteristic. Lean operation strategy has been investigated. At lean mixture conditions a significant drop in NOX and CO emissions was achieved. The fuel injection techniques and the impact of exhaust gas recirculation (EGR) on the conventional stoichiometric combustion process is highlighted.

Closed crankcase ventilation prevent harmful gases from entering atmosphere thereby reducing hydrocarbon emissions. Ventilation system carries blowby gases leaking through combustion process along with oil mist to Engine intake system. Major sources of blowby often occurs from leak in combustion chamber through piston rings, leaks from turbo shafts & valve guides. Oil mist carried away by blowby gases gets separated using filtration media. Fleece type separation media has high separation efficiency for particles above 10 microns. Efficiency drops if mist particle is below 10-micron size. Low size aerosol mist generally forms due to flash boiling on piston under crown area and on shafts of turbo charger due to high speeds combined with elevated oil temperatures. High power density diesel engine is taken for our study. It produces low particle size oil mist which contributes to aerosol emission of 3 gm/hr when operated at rated speed.

Following global trends of increasingly stringent greenhouse gas (GHG) and criteria pollutant regulations, India will likely introduce within the next decade equivalent Bharat Stage (BS) regulations for Diesel engines requiring simultaneous reduction in CO2 emissions and up to 90% reduction in NOx emission from current BS-VI levels. Consequently, automakers are likely to face tremendous challenges in meeting such emission reduction requirements while maintaining performance and vehicle total cost of ownership (TCO), especially in the Indian market which has experienced significant tightening of emission regulation during the past decade. Therefore, it is conceivable that cost effective approaches for improving existing diesel engines platforms for future regulations would be of high strategic importance for automakers.

As emissions standards become more stringent, OEMs are pushing engines to run on leaner fuel mixtures, which puts increased thermal stress on components, particularly pistons, causing them to operate at higher temperatures. This requires more robust design and rigorous testing of components. Telemetry methods offer accurate and real-time feedback, allowing designers to test components at various operating conditions, providing more flexibility than other traditional methods. Piston temperature measurement is a critical aspect of engine development because it directly affects engine performance and durability. Among the various techniques available for this purpose, telemetry methods have gained considerable attention in recent years. This method involves integrating temperature sensors and transmitter on the piston, which transmit temperature data wirelessly to a receiver outside the engine.

As per pieces of literature, 40 to 60 % of friction losses in an Internal combustion engine occur in piston-ring pack-liner assembly and, there is a significant supportive role of simulation in improving this assembly. Literature is also available which tells, how changes in pistons affect oil consumption. Thus, piston dynamics plays an important role in oil consumption. Furthermore, the Piston Movement Module simulation results also serve as a very important input for postprocessing to calculate piston ring dynamics. This research work is conducted to understand the effect of piston secondary motion, on oil consumption, blow-by, and friction. In this work, the results of ring dynamics and oil consumption simulation modules are studied with consideration and non-consideration of piston secondary motion results. The parameters like minimum oil film thickness, lubricating oil consumption, blow-by, friction, and friction power loss are investigated.

Reducing vehicular noise has become a crucial step in product development to meet stringent legislation and improve passenger experience. Smaller vehicles like three-wheelers and quadricycle are often powered by a single cylinder engine due to product cost, packaging and weight constraints. Unlike a multi-cylinder engine where cylinders fire one after another which helps to reduce noise levels by destructive interference of pressure waves, a single cylinder engine produces higher noise levels due to firing of only a single cylinder. Intake and exhaust flow noise is one of the dominant sources of vehicular noise. Testing performed on an actual vehicle demonstrates reduction in cabin noise levels by reducing intake and exhaust flow noise. This study focuses on using CAE tools to reduce intake and exhaust flow noise levels to meet target noise requirements.

Abstract At present, it is generally considered in the analysis of the secondary motion of engine piston that the piston skirt–cylinder liner friction pair is fully lubricated in an engine operating cycle. However, in practice, when the piston moves upward, the amount of lubricating oil at the inlet may not ensure that the friction pair is fully lubricated. In this article, the secondary motion of piston is studied when the transport of lubricating oil is considered to determine the lubrication condition of piston skirt–cylinder liner friction pair. The secondary motion of piston is solved based on the combined piston motion model, hydrodynamic lubrication model, asperity contact model, and lubricating oil flow model. The secondary motion equation of piston is solved by the Broyden method. The hydrodynamic lubrication equation is solved by the finite difference method. The asperity contact between piston skirt and cylinder liner is calculated by the Greenwood model.

A shock absorber endurance test for an automobile that was supposed to resist at least 200,000 load cycles but failed to meet the statutory fatigue limit was under examination. This is due to the breakdown of the assembly that holds the shock absorber shims. This failure occurred due to Fretting fatigue. A design improvement is being introduced to avoid fretting fatigue on the shock absorber shim assembly. FEA is used to investigate the shim assembly in order to locate the stress zone. After adding more shims to the piston, fatigue life was significantly improved. The damping forces were unaffected by the fundamental solution that was applied to make this improvement.

According to the Annual Energy Outlook 2022 (AEO2022) report, almost 30% of the transport sector will still use internal combustion engines (ICE) until 2050. The transportation sector has been actively seeking different methods to reduce the CO2 emissions footprint of fossil fuels. The use of lower carbon-intensity fuels such as Renewable Diesel (RD) can enable a pathway to decarbonize the transport industry. This suggests the need for experimental or advanced numerical studies of RD to gain an understanding of its combustion and emissions performance. This work presents a numerical modeling approach to study the combustion and emissions of RD. The numerical model utilized the development of a reduced chemical kinetic mechanism for RD’s fuel chemistry. The final reduced mechanism for RD consists of 139 species and 721 reactions, which significantly shortened the computational time from using the detailed mechanism.

It is a well-known fact that HCCI combustion offers the possibility of achieving high efficiency with low emissions, but with the challenges in combustion control and ability to adjust to changing environmental conditions. To resolve the aforementioned challenges, a pre-chamber induced homogeneous charge compression ignition (PC-HCCI) combustion mode was experimentally tested with aim of providing initial operating boundaries in terms of combustion stability and obtaining initial performance results. The single cylinder engine equipped with active pre-chamber and compression ratio (CR) of 17.5 was fueled by gasoline. The initial experiments were performed at the engine speed of 1600 rpm with intake air temperatures varied from 33°C to 100°C to verify the possibility of achieving the PC-HCCI combustion mode and to compare the achieved engine performance and emission results with both PCSI and pure HCCI combustion modes used as reference cases.

With the constant strive towards increase in performance and corresponding stringent emission standards of modern IC engine, engine components such as the head, block and piston are subjected to higher thermal loads. An integrated simulation methodology is proposed where the head, the block and the piston are integral part of the analysis. The CFD – CHT methodology is used to simulate and predict the temperature of these engine components. The head and block are run in a steady-state conjugate heat transfer framework while the transient multiphase volume of fluid (VOF) approach is used to predict piston temperatures. Combustion surfaces boundary conditions are derived from 3D CFD open-loop combustion simulation, while cooling and lubrication surface boundary condition are mapped from 1D system simulation or experimental data. The heat transfer boundary conditions are exchanged between the two simulations.

Several governments are increasing the blending mandate of renewable fuels to reduce the life-cycle greenhouse gas emissions of the road transport sector. Currently, ethanol is a prominent renewable fuel and is used in low-level blends, such as E10 (10 %v/v ethanol, 90 %v/v gasoline) in many parts of the world. However, the exact concentration of ethanol amongst other renewable fuel components in commercially available fuels can vary and is not known. To understand the impact of the renewable fuel content on the emissions from Euro 6d-TEMP emissions specification vehicles, this paper examines the real-driving emissions (RDE) from four 2020 to 2022 model-year vehicles run on E0 and E10 fuels. CO, CO2, NO, and NO2 were measured through a Portable Emissions Measuring System (PEMS).

The rapid development of the automobile industry has brought energy and environmental issues that scholars are increasingly concerning about. Improving efficiency and reducing emissions are currently two hot topics in the internal combustion engine industry. Direct water injection technology (DWI) can effectively reduce the cylinder temperature, which is due to the absorption of the heat by the injecting liquid water. In addition, lower temperature in the cylinder will reduce the formation of NO. In this paper, a CFD simulation of DWI application in a lean-burning single-cylinder engine with pre-chamber jet ignition was carried out. And the engine was experimentally tested for the simulation model validation. And then the effect of DWI strategy with different injecting water mass on the combustion and emissions characteristics are analyzed. Physically, injected water not only absorbs heat but also provides heat insulation.

Hydrogen has attracted attention as one of the key fuels for making internal combustion engines carbon neutral. However, the combustion characteristics of hydrogen differ greatly from those of conventionally used hydrocarbons. Therefore, in order to develop next-generation internal combustion engines that operate on hydrogen, it is first necessary to have a thorough understanding of the combustion characteristics of hydrogen. Engines that can take maximum advantage of those characteristics should be developed on the basis of that knowledge. Toward that end, the purpose of this study was to investigate the fundamental combustion characteristics of hydrogen in a test engine. This paper presents the results of an investigation of the effects on low-temperature oxidation reactions and autoignition when hydrogen was blended into dimethyl ether (DME) [1, 2], a gaseous hydrocarbon fuel.

Liquid fuel attached to the wall surface of the intake port, the piston and the combustion chamber is one of the main causes of the unburned hydrocarbon emissions from a port fueled SI engine, especially during transient operations. To investigate the liquid fuel film formation process and fuel film behavior during transient operation is essential to reduce exhaust emissions in real driving operations, including cold start operations. Optical techniques have been often applied to measure the fuel film in conventional reports, however, it is difficult to apply those previous techniques to actual engines during transient operations. In this study, using MEMS technique, a novel capacitance sensor has been developed to detect liquid fuel film formation and evaporation processes in actual engines. A resistance temperature detector (RTD) was also constructed on the MEMS sensor with the capacitance sensor to measure the sensor surface temperature.

For the survival of internal combustion engines, the required research right now is for alternative fuels, including drop-ins. Certain types of alternative fuels have been estimated to confirm the superiority in thermal efficiency. In this study, using a single-cylinder engine, olefin and oxygenated fuels were evaluated as a drop-in fuel considering the fuel characteristic parameters. Furthermore, the effect of various additive fuels on combustion speed was expressed using universal characteristics parameters.

Almost one-third of the fuel energy is wasted into the atmosphere via exhaust gas from an internal combustion engine. Despite several advancements in waste heat recovery technology, single-cylinder engines in the market that are currently in production remain naturally aspirated without any waste heat recovery techniques. Turbocharging is one of the best waste heat recovery techniques. However, a standard turbocharger cannot be employed in the single-cylinder engine due to technical challenges such as pulsated flow conditions at the exhaust, phase lag in the intake and exhaust valve opening. Of late, the emphasis on reducing exhaust emissions has been a primary focus for any internal combustion engine manufacturer, with the onset of stricter emission norms. Thus, the engine designer must prioritize emission reduction without compromising engine performance.

Abstract Using two subgrid-scale models of Smagorinsky and its dynamic version, large eddy simulation (LES) approach is applied to develop a 3D computer code simulating the in-cylinder flow during intake and compression strokes in an engine geometry consisting of a pancake-shaped piston with a fixed valve. The results are compared with corresponding experimental data and a standard K-Ɛ turbulence model. LES results generally show better agreement with available experimental data suggesting that LES with dynamic subgrid-scale model is more effective method for accurately predicting the in-cylinder flow field.

Recently, it has been wildly recognized that active pre- chamber has a significant effect on extending the lean burn limit of gasoline engines. Ion current signals in the combustion is also considered as a promising approach to the engine knock detection. In this study, the feasibility of employing ion current in an active pre- chamber for combustion diagnosis was analyzed by three-dimensional numerical simulation on a single- cylinder engine equipped with active pre-chamber. The flow characteristics of charged species (NO+, H3O+ and electrons) in the main chamber and pre-chamber under knock conditions are investigated at different engine speeds, intake pressures and ignition timings. The results show that the ion current can theoretically be used for the knock detection of the active pre- chamber. The peak value of the electron or H3O+ mass fraction caused by knocking backflow can be used as knock indication peak.