Refine Your Search

Search Results

Standard

Cutting Edge - Double Bevel Cross Sections

2019-04-22
WIP
J738
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: a. Scrapers as defined in ISO 7133. b. Dozers as described in ISO 6747. c. Loaders as described in ISO 7131. d. Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.
Standard

Rated Operating Load for Loaders

2013-01-02
CURRENT
J818_201301
This SAE Standard establishes the definition of a normal all day rated operating load for loaders as defined in SAE J1057. This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

2011-12-08
CURRENT
J743_201112
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Nomenclature - Rollers and Compactors

2011-10-27
CURRENT
J1017_201110
This SAE Standard provides names of major components peculiar to rollers and compactors. Illustrations of components are not intended to be exactly descriptive of any particular machine. NOTE: Rollers and compactors will be defined in a section added to SAE J1057a.
Standard

Earthmoving Machinery-Coupling of Attachments to Skid Steer Loaders

2008-05-01
CURRENT
J2513_200805
This SAE Standard sets forth standard dimension requirements for the loader attachment bracket and attachment interface to allow interchangeability of attachments on skid steer loaders whose operating mass (see SAE J/ISO 6165) is 4,500 kg or less. Narrow skid steer loaders may have a width that does not allow compliance with this standard. The design of the loader attachment bracket locking system is not restricted by this standard and is left to the discretion of the manufacturer. The purpose of this document is to provide dimensions to standardize the coupling interface between skid steer loaders and their attachments that are manufactured worldwide.
Standard

Machine Slope Operation Test Code

2003-05-12
CURRENT
J897_200305
This SAE Standard applies to off-road self-propelled construction, forestry and industrial machines as listed in categories 1, 2, and 4 of SAE J1116. Purpose This Standard provides a field procedure to determine the ability of a machine to operate statically and dynamically on sloping surfaces. Depending upon the objective of the test, any item listed as specified is to be selected at the discretion of either the manufacturer, the test agency, the owner, or a combination of these parties.
Standard

Nomenclature--Crawler Tractor

2002-02-21
CURRENT
J727_200202
This Standard provides provides names of major components peculiar to crawler tractors as defined in SAE J1057a (June, 1975). Illustrations of components are not intended to be exactly descriptive of any particular machine.
Standard

Drawbars--Crawler Tractor

2002-02-21
CURRENT
J749_200202
This SAE Standard provides recommended dimensions for drawbars for crawler tractors as defined in SAE J1057 (SEP88). It includes only those dimensions which will affect the attaching of towed equipment.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

2000-06-01
HISTORICAL
J743_200006
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Hole Placement on Dozer End Bits

1998-05-01
CURRENT
J63_199806
The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057a up to a maximum weight of 100,000 lb (45,000 kg).
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

1992-03-01
HISTORICAL
J743_199203
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Component Nomenclature-Graders

1990-07-30
HISTORICAL
J870_199007
This SAE Standard provides names of major components peculiar to graders as defined in SAE J1057 (See Figure 1). Illustrations are not intended to be exactly descriptive of any particular machine.
Standard

Component Nomenclature-Scrapers

1990-07-01
HISTORICAL
J728_199007
This SAE Standard provides names of major components peculiar to the scraper portion of tractor-scrapers. Reference J1057. Illustrations of components are not intended to be exactly descriptive of any particular machine.
Standard

Cutting Edge-Curved Grader

1986-06-01
HISTORICAL
J739_198606
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580. This document specifes hole placement along the length and width of the cutting edge and dimensions for cutting edge cross sections. See Table 1.
Standard

Hole Placement on Dozer End Bits

1986-05-01
HISTORICAL
J63_198605
It is the purpose of the SAE Recommended Practice to define the minimum requirements for hole placement on Dozer End Bit supports. The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057a up to a maximum weight of 100,000 lb (45,000 kg).
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

1986-05-01
HISTORICAL
J743_198605
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Capacity Rating--Dozer Blades

1986-05-01
HISTORICAL
J1265_198605
This standard applies only to straight, angling, semi-U, and U-blades for crawler and wheel tractors. It applies to angling blades only in the straight (not angled) position. This standard does not apply to angled blades or other tools used to side cast materials, nor does it apply to any blade with design features such as end plates extended beyond the blade face. This standard assumes the blade face to be flat and vertical, and does not consider the blade included volume (Figure 1). Although provisions are presented for some deviations, this standard is intended for rectangular blades whose width/height ratios are at least 1.0. Purpose The purpose of this standard is to provide a uniform method for calculating the capacities of dozer blades. It is intended for relative comparisons of dozer blade capacity, and not for predicting capacities or productivities in actual field conditions.
Standard

Nomenclature-Crawler Tractor

1986-01-01
HISTORICAL
J727_198601
This Standard provides provides names of major components peculiar to crawler tractors as defined in SAE J1057a (June, 1975). Illustrations of components are not intended to be exactly descriptive of any particular machine.
X