Refine Your Search

Search Results

Viewing 1 to 14 of 14
Standard

Rated Operating Load for Loaders

2013-01-02
CURRENT
J818_201301
This SAE Standard establishes the definition of a normal all day rated operating load for loaders as defined in SAE J1057. This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

2011-12-08
CURRENT
J743_201112
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

2000-06-01
HISTORICAL
J743_200006
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

1986-05-01
HISTORICAL
J743_198605
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Capacity Rating--Dozer Blades

1986-05-01
HISTORICAL
J1265_198605
This standard applies only to straight, angling, semi-U, and U-blades for crawler and wheel tractors. It applies to angling blades only in the straight (not angled) position. This standard does not apply to angled blades or other tools used to side cast materials, nor does it apply to any blade with design features such as end plates extended beyond the blade face. This standard assumes the blade face to be flat and vertical, and does not consider the blade included volume (Figure 1). Although provisions are presented for some deviations, this standard is intended for rectangular blades whose width/height ratios are at least 1.0. Purpose The purpose of this standard is to provide a uniform method for calculating the capacities of dozer blades. It is intended for relative comparisons of dozer blade capacity, and not for predicting capacities or productivities in actual field conditions.
Standard

Capacity Rating--Scraper, Open Bowl

1985-01-01
HISTORICAL
J741_198501
This SAE Standard specifies a procedure for approximating the volume of typical materials contained in the bowl of Open Bowl scrapers as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and representative volumes on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

Capacity Rating--Elevating Scrapers

1985-01-01
HISTORICAL
J957_198501
This SAE Standard specifies a procedure for approximating the volume of a typical material carried in the bowl of an elevating scraper as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and a representative volume on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

Capacity Rating--Dozer Blades

1980-02-01
HISTORICAL
J1265_198002
This standard applies only to straight, angling, semi-U, and U-blades for crawler and wheel tractors. It applies to angling blades only in the straight (not angled) position. This standard does not apply to angled blades or other tools used to side cast materials, nor does it apply to any blade with design features such as end plates extended beyond the blade face. This standard assumes the blade face to be flat and vertical, and does not consider the blade included volume (Figure 1). Although provisions are presented for some deviations, this standard is intended for rectangular blades whose width/height ratios are at least 1.0. Purpose The purpose of this standard is to provide a uniform method for calculating the capacities of dozer blades. It is intended for relative comparisons of dozer blade capacity, and not for predicting capacities or productivities in actual field conditions.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

1979-03-01
HISTORICAL
J743B_197903
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Machine Slope Operation Test Code

1978-05-01
HISTORICAL
J897_197805
This SAE Standard applies to off-road self-propelled construction, forestry and industrial machines as listed in categories 1, 2, and 4 of SAE J1116. Purpose This Standard provides a field procedure to determine the ability of a machine to operate statically and dynamically on sloping surfaces. Depending upon the objective of the test, any item listed as specified is to be selected at the discretion of either the manufacturer, the test agency, the owner, or a combination of these parties.
Standard

Lift Capacity Calculation and Test Procedure-Pipelayer and Sideboom

1977-06-01
HISTORICAL
J743A_197706
This SAE Standard describes a method to calculate and a test procedure to validate rated lift capacity as presented in commercial literature for pipelayers and tractors or loaders (wheel or crawler), equipped with a hydraulic or mechanically operated sideboom. Rated lift capacity considers hoist mechanism limits, tipping loads, and rope factor. After the lift capacity is validated by testing, a reduction factor is applied to establish the rated lift capacity for the specific pipelayer or sideboom configuration.
Standard

Capacity Rating--Scraper, Open Bowl

1975-06-01
HISTORICAL
J741B_197506
This SAE Standard specifies a procedure for approximating the volume of typical materials contained in the bowl of Open Bowl scrapers as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and representative volumes on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

Capacity Rating--Loader Bucket

1975-06-01
HISTORICAL
J742B_197506
This standard applies to buckets of loaders (as defined by SAE J1057a, Identification Terminology of Earthmoving Machines). This method applies primarily to buckets having parallel sides and a cutting edge parallel to the top edge of the top edge of the back sheet. Moderately clipped back sheet corners will introduce no appreciable errors. Bucket teeth, tooth adapters, as well as other similar local discontinuities are ignored. a. Interpretation of irregular shaped cutting edges is identified in 4.4. b. Interpretation of irregular shaped side sheets is identified in 4.5.
Standard

Capacity Rating--Elevating Scrapers

1975-06-01
HISTORICAL
J957_197506
This SAE Standard specifies a procedure for approximating the volume of a typical material carried in the bowl of an elevating scraper as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and a representative volume on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
X