Achieving stable combustion without misfire and knocking is challenging in premixed charge compression ignition (PCCI) especially in small bore, air cooled diesel engines owing to lower power output and inefficient cooling system. In the present study, a single cylinder, air cooled diesel engine used for agricultural water pumping applications is modified to run in PCCI by replacing an existing mechanical fuel injection system with a flexible common rail direct injection system. An advanced start of fuel injection (SOI) and exhaust gas recirculation (EGR) are required to achieve PCCI in the test engine. Parametric investigations on SOI, EGR and fuel injection pressure are carried out to identify optimum parameters for achieving maximum brake thermal efficiency. An SOI sweep of 12 to 50 deg. CA bTDC is done and for each SOI, EGR is varied from 0 to 50% to identify maximum efficiency points. It was found that EGR helps in extending the load range from 20 to 40% of rated load.
The fuel economy of recent small size DI diesel engines has become more and more efficient. However, heat loss is still one of the major factors contributing to a substantial amount of energy loss in engines. In order to a full understanding of the heat loss mechanism from combustion gas to cylinder wall, the effect of hole size and rail pressure under similar injection rate conditions on transient heat flux to the wall were investigated. Using a constant volume vessel with a fixed impingement wall, the study measured the surface heat flux of the wall at the locations of spray flame impingement using three thin-film thermocouple heat-flux sensors. The results showed that the characteristic of local heat flux and soot distribution was almost similar by controlling similar injection rate except for the small nozzle hole size with increasing injection pressure.
Lean burn gasoline engines can achieve noteworthy fuel consumption and power output. However, when the mixture becomes lean, the ignition delay increases, and the flame propagation speed becomes slow, which lead to increase the combustion fluctuation. The glow plug is usually used to solve the cold start problem in diesel engines, where the compression temperature might not be high enough to ensure the proper ignition of the injected fuel, resulting in instability combustion and increased exhaust emissions. Based on this point, the present study intends to install a glow plug to the sub-chamber. Experiments were conducted on a modified single cylinder four-stroke CI engine (YANMAR TF120V) to operate as SI engine with a higher compression ratio compared to the conventional SI engines, 15.1:1. The engine is operated at a constant speed of 1000 rpm for different equivalence ratios with different voltage of glow plug which creates the temperature variation inside the sub-chamber.
In the present work, a relative comparison of addition of water to diesel through emulsion and fumigation methods is explored for reducing oxides of nitrogen (NOx) and smoke emissions in a production small bore diesel engine. The water to diesel ratio was kept the same in both the methods at a lower concentration of 3% by mass to avoid any adverse effects on the engine system components. The experiments were conducted at a rated engine speed of 1500 rpm under varying load conditions. A stable water-diesel emulsion was prepared using a combination of equal proportions (1:1 by volume) of Span 80 and Tween 80. The mixture of Span 80 in diesel and Tween 80 in water was homogenized using an IKA Ultra Turrax homogenizer with tip stator diameter 18mm at 5000 rpm for 2 minutes. The water-in-diesel emulsions thus formulated were kinetically stable and appeared translucent. No phase separation was observed on storage for approximately 105 days.
Due to the increasing computational power, significant progress has been made over the past decades when it comes to CAD, multibody and simulation software. The application of this software allows to develop products from scratch, or to investigate the static and dynamic behavior of multibody models with remarkable precision. In order to keep the development costs low for highly sophisticated products, more precisely motorcycle rider assistance systems, it is necessary to focus extensively on the virtual prototyping using different software tools. In general, the interconnection of different tools is rather difficult, especially when considering the coupling of a detailed multibody model with a simulation software like MATLAB Simulink. The aim of this paper is to demonstrate the performance of a motorcycle rider assistance algorithm using a cosimulation approach between the free multibody software called FreeDyn and Simulink based on a sophisticated multibody motorcycle model.
In the last decade, pollution by particulate matter and its effect on human health has increasingly become the focus of public attention. In order to monitor and evaluate particulate pollution, expensive measuring stations were placed at traffic hotspots and other selected locations. The measuring devices often precisely record the particle concentration, but have disadvantages in mobility and for measurements in large-area due to their size and investment costs. A measurement with high temporal and spatial resolution is not possible with these stations. This paper presents a new type of mobile particulate sensor based on the Plantower PMS 7003 particle sensor. In addition to the Plantower sensor, a rechargeable battery and newly developed control electronics are also installed in the particulate sensor. Due to the small size and the low manufacturing costs of the measuring system, mobile usage in higher quantity is possible.
Despite the increase in public attention to particulate matter emissions since the millennium and the known effects on the human organism, representative predictions on the dispersion of emissions in both urban and rural areas are hardly possible so far. Especially the validation of simulations with measurement results is not possible due to the limited number and high price of certified measuring instruments. Rather, the temporally high-resolution measuring instruments are only sporadically distributed within the city, so that emission dynamics at traffic hotspots, such as traffic jams or intersections, cannot be depicted. Furthermore, due to the small number of certified measuring instruments, fine dust pollution can only be interpolated over long distances. In this paper, first statements about the transport characteristics of particles at a road intersection will be made by using a variety of so-called low-cost particulate matter sensors.
The aim of the presented research is to propose and benchmark two brake models, namely the novel dynamic ILVO model and a neural network based regression. These can estimate the evolution of the brake friction between pad and disc under different load conditions, which are typically experienced in vehicle applications. The research also aims improving the knowledge of the underlying mechanism related to the evolution of the BLFC (boundary layer friction coefficient), the reliability of virtual environment simulations to speed up the product development time and reducing the amount of vehicle test in later phases and finally improving brake control functions. With the support of extensive brake dynamometer testing, the proposed models are benchmarked against State-of-the-Art. Both approaches are parametrised to render the friction coefficient dynamics with respect to the same input parameters.