Search Results

Diesel engines are largely used as power units with high fuel efficiency. Conversely, they have an adverse impact on the environment and human health as they emit high NOx and particulate Matter (PM) emissions. As more stringent regulations for emissions are introduced, low temperature combustion (LTC) strategy such as Gasoline Compression Ignition (GCI) demonstrated the potential to reduce the PM, NOx emissions by operating engines under a Partially Premixed Combustion (PPC) mode. Therefore, A 0.550 mm single cylinder engine SCE, which is operated at Gasoline Direct Injection Ignition (GDCI), was tested over range of engine loads with constant speed (1500 rpm) using RON80 without oxygenate. Different operating parameters such as injection were used to control combustion phasing and mixture stratifications. At low loads, rebreathing (RB) of hot exhaust gas produced low levels of NOx and smoke emissions.

For the survival of internal combustion engines, the required research right now is for alternative fuels, including drop-ins. Certain types of alternative fuels have been estimated to confirm the superiority in thermal efficiency. In this study, using a single-cylinder engine, olefin and oxygenated fuels were evaluated as a drop-in fuel considering the fuel characteristic parameters. Furthermore, the effect of various additive fuels on combustion speed was expressed using universal characteristics parameters. In addition, the prediction of CO2 emission from passenger cars were carried out by changing the fuels. The CO2 emission in running WLTC was estimated using Modelica. As a result, it was found that the CO2 emission can be reduced by adding olefin and oxygenated fuels.

With the increasing pursuit of comfort in mobility, NVH characteristics are becoming more important than ever. Achieving a benchmark beating NVH behavior involves optimizing source, transfer paths as well as target location mechanical characteristics. In ICE vehicles, powertrain accounts for a major source of noise and vibration. This work encompasses NVH refinement strategies for a single-cylinder compression ignition engine. The work starts with setting target values for NVH characteristics based on competitive benchmark data analysis. A complete development strategy involving extensive testing and CAE correlation is presented here. Contribution analysis in the component level for optimization of NVH behavior is carried out by employing NVH testing in an anechoic chamber supported by CAE simulations.

Reduction of CO2 emissions from transportation is mandatory to limit global warming. New Energy Vehicles (NEV) need to be used widely in order to reach this goal. NEV include Battery Electric Vehicles (BEV), Hybrid Electric Vehicles (HEV), Plug-in Hybrid Electric Vehicles (PHEV) and Fuel Cell Electric Vehicles (FCEV). From a Life Cycle Analysis point of view, considering the CO2 emissions produced by battery manufacturing and during vehicle use, the most promising technology is the PHEV operating on green fuels. However, the internal combustion engine remains a source of gaseous pollution in urban areas. The combustion process has to be further improved to comply with latest and most stringent exhaust emission standards. One way to achieve this objective is the use of eco-friendly fuels like hydrogen to reduce engine-out emissions (NOx, soot and CO2) in PHEV system.

For the purpose of achieving carbon-neutrality in the mobility sector by 2050, hydrogen can play a crucial role as an alternative energy carrier, not only for direct usage in fuel cell-powered vehicles, but also for fueling internal combustion engines. This paper focuses on the numerical investigation of high-pressure hydrogen injection and the mixture formation inside a high-tumble engine with a conventional liquid fuel injector for passenger cars. Since the traditional 3D-CFD approach of simulating the inner flow of an injector requires a very high spatial and temporal resolution, the enormous computational effort, especially for full engine simulations, is a big challenge for an effective virtual development of modern engines. An alternative and more pragmatic lagrangian 3D-CFD approach offers opportunities for a significant reduction in computational effort without sacrificing reliability.

Abstract Low-temperature heat release (LTHR) is of interest for its potential to help control autoignition in advanced compression ignition (ACI) engines and mitigate knock in spark ignition (SI) engines. Previous studies have identified and investigated LTHR in both ACI and SI engines before the main high-temperature heat release (HTHR) event and, more recently, LTHR in isolation has been demonstrated in SI engines by appropriately curating the in-cylinder thermal state during compression and disabling the spark discharge. Ethanol is an increasingly common component of market fuel blends, owing to its renewable sources. In this work, the effect of adding ethanol to iso-octane (2,2,4-trimethylpentane) blends on their LTHR behavior is demonstrated. Tests were run on a motored single-cylinder engine elevated inlet air temperatures and pressures were adjusted to realize LTHR from blends of iso-octane and ethanol without entering the HTHR regime.

Abstract TOC

The piston and piston ring are used in a severe contact environment in engine durability tests, which causes severe wear to the piston ring groove, leading to significant development costs for countermeasures. Conventionally, in order to ensure functional feasibility through wear on the piston top ring groove (hereinafter “ring groove”), only functional evaluations through actual engine durability testing were performed, and there was an issue in determining the limit value for the actual amount of wear itself. Because of this, the mechanism that may cause wear on the ring groove was clarified through past research, but this resulted in judgment criteria with some leeway from the perspective of functional assurance. To establish judgment criteria, it was necessary to understand both functional effect from ring groove wear and the mechanism behind it.

In the context of carbon neutrality, ammonia is considered a zero-carbon fuel with potential applications in the transportation sector. However, its high ignition energy, low flame speed, and high natural temperature, indicative of low reactivity, make it challenging to be applied as a sole fuel in engines. In such a scenario, the use of another zero-carbon and highly reactive fuel, hydrogen, becomes necessary to enhance the combustion of ammonia. Furthermore, jet ignition, a method known for improving engine combustion performance, may also hold potential for enhancing the combustion performance of ammonia engines. To explore the applicability of jet ignition in engines, this study conducted experimental research on a single-cylinder engine. Two ignition methods were employed: passive jet ignition of premixed ammonia-hydrogen at a compression ratio of 11.5, and active jet ignition of pure ammonia using hydrogen jet flame at a compression ratio of 17.3.

Testing of ducted fuel injection (DFI) in a single-cylinder engine with production-like hardware previously showed that adding a duct structure increased soot emissions at the full load, rated speed operating point [1]. The authors hypothesized that the DFI flame, which travels faster than a conventional diesel combustion (CDC) flame, and has a shorter distance to travel, was being re-entrained into the on-going fuel injection around the lift-off length (LOL), thus reducing air entrainment into the on-going injection. The engine operating condition and the engine combustion chamber geometry were duplicated in a constant pressure vessel. The experimental setup used a 3D piston section combined with a glass fire deck allowing for a comparison between a CDC flame and a DFI flame via high-speed imaging. CH* imaging of the 3D piston profile view clearly confirmed the re-entrainment hypothesis presented in the previous engine work.

This work represents an advanced engineering research project partially funded by the U.S. Department of Energy (DOE). Ford Motor Company, FEV North America, and Oak Ridge National Laboratory collaborated to develop a next generation boosted spark ignited engine concept. The project goals, specified by the DOE, were 23% improved fuel economy and 15% reduced weight relative to a 2015 or newer light-duty vehicle. The fuel economy goal was achieved by designing an engine incorporating high geometric compression ratio, high dilution tolerance, low pumping work, and low friction. The increased tendency for knock with high compression ratio was addressed using early intake valve closing (EIVC), cooled exhaust gas recirculation (EGR), an active pre-chamber ignition system, and careful management of the fresh charge temperature.

Abstract Improving thermal efficiency of an internal combustion engine is one of the most cost-effective ways to reduce life cycle-based CO2 emissions for transportation. Lean burn technology has the potential to reach high thermal efficiency if simultaneous low NOx, HC, and CO emissions can be achieved. Low NOx can be realized by ultra-lean (λ ≥ 2) spark-ignited combustion; however, the HC and CO emissions can increase due to slow flame propagation and high combustion variability. In this work, we introduce a new combustion concept called turbulent jet-controlled compression ignition, which utilizes multiple turbulent jets to ignite the mixture and subsequently triggers end gas autoignition. As a result, the ultra-lean combustion is further improved with reduced late-cycle combustion duration and enhanced HC and CO oxidation. A low-cost passive prechamber is innovatively fueled using a DI injector in the main combustion chamber through spray-guided stratification.

With the increasing focus on reducing CO2 emissions to combat global warming and climate change, the automotive industry is exploring near zero-emission alternative fuels to replace traditional fossil-based fuels like diesel, gasoline, and CNG. Methanol is a promising alternative fuel that is being evaluated in India due to its easy transportation and storage, as well as its production scalability and availability potential. This study focuses on the retro-fitment solution of M100 (pure methanol) SI port-fuel injection (PFI) mode of combustion. A heavy duty single-cylinder engine test setup was used to assess methanol SI combustion characteristic. Lean operation strategy has been investigated. At lean mixture conditions a significant drop in NOX and CO emissions was achieved. The fuel injection techniques and the impact of exhaust gas recirculation (EGR) on the conventional stoichiometric combustion process is highlighted.

Reducing vehicular noise has become a crucial step in product development to meet stringent legislation and improve passenger experience. Smaller vehicles like three-wheelers and compact cars are often powered by a single cylinder engine due to product cost, packaging and weight constraints. Unlike a multi-cylinder engine where cylinders fire one after another which helps to reduce noise levels by destructive interference of pressure waves, a single cylinder engine produces higher noise levels due to firing of a single cylinder. Intake and exhaust flow noise is one of the dominant sources of vehicular noise. This study focuses on using CAE tools to reduce intake and exhaust flow noise levels to meet target noise requirements. One dimensional (1-D) gas dynamics simulation provides a good trade-off between accuracy and run-time, allowing for evaluation of multiple design iterations with acceptable accuracy in a relatively short time frame.

Computational tools have become indispensable in the development of cam profiles, aiding designers in achieving optimal performance. This paper explores the application of computational tools in the design of cam profiles for a single-cylinder research engine (SCRE) prototype under development with a direct-acting mechanism. The primary objective is to present a comprehensive design process, encompassing kinematic analysis and Quasi-Dynamic Analysis (QDA), to enable designers to generate preliminary cam profiles based on design requirements. The VT-Design® software, a part of the GT-SUITE package, is employed for simulations in this study. Key design considerations, such as lift, velocity, and acceleration curves, are discussed, emphasizing the importance of maintaining continuity in the acceleration curve. The design process involves optimizing the acceleration curve to minimize negative acceleration and improve dynamic response.

Abstract Despite the growing prominence of electrified vehicles, internal combustion engines remain essential in future transportation. This study delves into passive pre-chamber jet ignition, a leading-edge combustion technology, offering a comprehensive visualization of its operation under varying load and dilution conditions in light-duty GDI engines. Our primary objectives are to gain fundamental insights into passive pre-chamber jet ignition and subsequent main combustion processes and evaluate their response to different load and dilution conditions. We conducted experimental investigations using a light-duty, optical, single-cylinder engine equipped with three passive pre-chamber designs featuring varying nozzle diameters. Optical diagnostic imaging and heat release analysis provided critical insights.

According to the Annual Energy Outlook 2022 (AEO2022) report, almost 30% of the transport sector will still use internal combustion engines (ICE) until 2050. The transportation sector has been actively seeking different methods to reduce the CO2 emissions footprint of fossil fuels. The use of lower carbon-intensity fuels such as Renewable Diesel (RD) can enable a pathway to decarbonize the transport industry. This suggests the need for experimental or advanced numerical studies of RD to gain an understanding of its combustion and emissions performance. This work presents a numerical modeling approach to study the combustion and emissions of RD. The numerical model utilized the development of a reduced chemical kinetic mechanism for RD’s fuel chemistry. The final reduced mechanism for RD consists of 139 species and 721 reactions, which significantly shortened the computational time from using the detailed mechanism.

It is a well-known fact that HCCI combustion offers the possibility of achieving high efficiency with low emissions, but with the challenges in combustion control and ability to adjust to changing environmental conditions. To resolve the aforementioned challenges, a pre-chamber induced homogeneous charge compression ignition (PC-HCCI) combustion mode was experimentally tested with aim of providing initial operating boundaries in terms of combustion stability and obtaining initial performance results. The single cylinder engine equipped with active pre-chamber and compression ratio (CR) of 17.5 was fueled by gasoline. The initial experiments were performed at the engine speed of 1600 rpm with intake air temperatures varied from 33°C to 100°C to verify the possibility of achieving the PC-HCCI combustion mode and to compare the achieved engine performance and emission results with both PCSI and pure HCCI combustion modes used as reference cases.