Search Results

Noise, vibration and harshness (NVH) is one of the most important performance evaluation aspect of electric motors. Among the different causes of the NVH issues of electrical drives, the high-frequency spatial and temporal harmonics of the electrical drive system is of great importance. To reduce the tonal noise of the electric motors, harmonic injection methods can be applied. However, a lot of the existing related work focuses more on improving the optimization process of the parameter settings of the injected current/flux/voltage, which are usually limited to some specific working conditions. The applicability and effectivity of the algorithm to the whole frequency/speed range are not investigated. In this paper, a multi-domain pipeline of harmonic injection controller design for a permanent magnet synchronous motor (PMSM) is proposed.

Find out why you should attend the 2025 Noise and Vibration Conference and Exhibition.

Contact the appropriate representative of the 2025 Noise and Vibration Conference and Exhibition.

Request exhibit and sponsor information for the 2025 Noise and Vibration Conference and Exhibition.

Off-roading is the scenario of driving a vehicle on unpaved surfaces such as sand, gravel, riverbeds, rocks, and other natural terrain. Vehicle designed for that purpose requires jumping from height due to uneven surfaces/patches. This also requires them to sustain a high amount of loads acting upon them on impact. Thus, off-roading vehicles should not only provide intended vehicle dynamics performance but at the same time should be durable as well. Drop test which is done in a controlled environment is a widely used method to validate the durability of vehicle in such scenarios wherein the vehicle is dropped from a certain predefined height. In Multibody dynamics simulation, drop test was replicated and acceleration data computed at different locations in the vehicle were correlated with actual physical test data. Correlation was done for different drop heights. This paper presents relevant details of the virtual vehicle modeling, loadcase, test data & subsequent correlation.

Focused on the permanent magnet synchronous motor (PMSM) used in electric, this paper proposes an online insulation testing method based on voltage injection under high-temperature and high-humidity conditions. The effect of constant humidity and temperature on the insulation performance has been also studied. Firstly, the high-voltage insulation structure and principle of PMSM are analyzed, while an electrical insulation testing method considered constant humidity and temperature is proposed. Finally, a temperature and humidity experimental cycling test is carried out on a certain prototype PMSM, taking heat conduction and radiation models, water vapor, and partial discharge into account. The results show that the electrical insulation performance of the motor under constant humidity and temperature operation environment exhibits a decreasing trend. This study can provide theoretical and practical references for the reliable durability design of PMSM.

Soft magnetic cores of electric motors and generators are normally manufactured by stamping individual circular laminates from non-oriented electrical steel (NOES) sheets and stacking them layer by layer to reach the required height. The traditional lamination method can only achieve the average performance of the NOES since the magnetization is in all the directions of the sheet plane. Although NOES is ideal to have isotropic magnetic properties in all the directions of the sheet plane, commercially available electrical steel sheets always show apparent anisotropy in the rotating magnetization directions lying in the sheet plane. The anisotropy in magnetic properties not only causes fluctuations in the rotating magnetic field, but also leads to oscillations in electromagnetic torque, and thus needs to be minimized.

Certain sports utility vehicles (SUVs) utilize dual latches and gas struts in their hood design. This is primarily driven by the larger size of the hood and specific architectural requirements. These hoods can be securely latched either by a dynamic single stroke closing method or by quasistatic two stroke closing method. In dynamic method, the hood is closed with a single, high-velocity motion for the final primary latching, whereas in quasistatic method, force is initially applied for the secondary latching and then for the final primary latching. In this study, both the dynamic and quasistatic closing methods are compared in terms of closing force and velocity and hood over travel distance. A load cell is used for measuring the closing force, velocity meter is used for velocity measurement and a rope sensor is used for measuring the hood over travel distance.

In electric vehicle applications, the majority of the traction motors can be categorized as Permanent Magnet (PM) motors due to their outstanding performance. As indicated in the name, there are strong permanent magnets used inside the rotor of the motor, which interacts with the stator and causes strong magnetic pulling force during the assembly process. How to estimate this magnetic pulling force can be critical for manufacturing safety and efficiency. In this paper, a full 3D magnetostatic model has been proposed to calculate the baseline force using a dummy non-slotted cylinder stator and a simplified rotor for less meshing elements. Then, the full 360 deg model is simplified to a half-pole model based on motor symmetry to save the simulation time from 2 days to 2 hours. A rotor position sweep was conducted to find the maximum pulling force position. The result shows that the max pulling force happens when the rotor is 1% overlapping with the stator core.

Due to the expense and time commitment associated with extensive product testing, vehicle manufacturers are developing new simulation techniques to verify vehicle component performance with less testing and more confidence in the final product. Battery lifetime is of particular difficulty to predict, since each battery is different and there are many different control scenarios that could be implemented based on the specific requirements of each battery type. In order to solve this problem for a 12V auxiliary lead-acid battery, a battery durability analysis model has been previously adapted from lithium-ion applications, which is capable of verifying the impact of lead-acid battery durability in a short period of time. In this study, calibration tools for this model were developed and are presented here, and durability analysis and verification are performed for the application of new electric vehicles.

This paper analyzes the leakage magnetic field generated by the Bi-Directional wireless charging system of Electric Vehicle(EV) and confirms the effect of the shielding coil in the Bi-Directional wireless charging system. In particular, in EV using the Inductive Power Transfer(IPT) method, the effective shielding coil position is proposed by analyzing the contribution of the leakage magnetic field of the Ground Assembly(GA) coil and the Vehicle Assembly(VA) coil according to the power transfer direction. Simulations were conducted using the WPT3/Z2 model of the standard SAE J2954, and it was confirmed that the GA coil contributed more to the leakage magnetic field due to the relatively large size compared to the VA coil regardless of power transfer direction.

With the rapid development of electric vehicles, the demands for lithium-ion batteries and advanced battery technologies are growing. Today, lithium-ion batteries mainly use liquid electrolytes, containing organic compounds such as dimethyl carbonate and ethylene carbonate as solvents for the lithium salts. However, when thermal runaway occurs, the electrolyte decomposes, venting combustible gases that could readily be ignited when mixed with air and leading to pronounced heat release from the combustion of the mixture. So far, the chemical behavior of electrolytes during thermal runaway in lithium-ion batteries is not comprehensively understood. Well-validated compact chemical kinetic mechanisms of the electrolyte components are required to describe this process in CFD simulations. In this work, submechanisms of dimethyl carbonate and ethylene carbonate were developed and adopted in the Ansys Model Fuel Library (MFL).

This paper presents a numerical methodology to generate lookup tables that provide d- and q-axis stator current references for the control of electric motors. The main novelty with respect to other literature references is the introduction of the iron power losses in the equivalent-circuit electric motor model implemented in the optimization routine. The lookup tables generation algorithm discretizes the motor operating domain and, given proper constraints on maximum stator current and magnetic flux, solves a numerical optimization problem for each possible operating point to determine the combination of d- and q- axis stator currents that minimizes the imposed objective function while generating the desired torque. To demonstrate the versatility of the proposed approach, two different variants of this numerical interpretation of the motor control problem are proposed: Maximum Torque Per Ampere and Minimum Electromagnetic Power Loss.

This paper reviews the current situation in the development of accelerated testing of automotive engineering, consisting of the four following areas: 1. Field testing of the natural product. 2. Additional technology of separate testing in the laboratory on the basis of physical simulation of separate field conditions using corresponding methods and equipment separately and conducting: safety testing, special programs of testing using digital simulation, special testing with changing certain parameters of environment, corrosion testing, etc. Both of the traditional testing developments above can be found in many magazines, journals, conferences, presentations, and proceedings. 3. Testing on the basis of digital (computer) simulation of product and/or field conditions. This area of testing has been developed in the last dozen years. Many articles and presentations were published during this time. 4.

Validation of powertrain systems is nowadays performed with specific durability relevant load cycles, which represent the lifetime requirement of individual powertrain components. The definition of such durability relevant load cycles, which are used for vehicle testing should ideally be based on the actual vehicle's usage. Recording driving cycles within a vehicle is one of the most typical ways of collecting vehicle usage and relevant end customer behavior, but the generation of such measured vehicle data can be time consuming. In addition, this method of capturing on-road measurements has limitations in the variation of vehicle loadings (e.g., number of passengers, luggage, trailer usage etc.). Especially for new applications, entering new target markets, these kinds of in-vehicle measurements are not possible in early development stages, as the required vehicle or powertrain configuration is not available in hardware or incapable of measurements.

The powertrain system plays a crucial role in electric vehicles, exerting significant impact on both the dynamic and economic performances. A breakthrough has been observed by using the dual-motor powertrain system, which outperformed its single-motor counterparts. This study reports a dual-motor powertrain with magnetorheological technology. The powertrain consists of two motors, two magnetorheological brakes and a planetary gear set. Via regulating the brakes, the power transmission flow can be controlled to realise different torque ratios and velocities. The synergetic control of motors and brakes is capable of achieving smooth gear shifting without interruption. This paper details the design of the powertrain system: the structural configuration of the magnetorheological brakes is highlighted, the magnetic field distribution of the brakes under different currents is simulated by COMSOL Multiphysics, and the torque capacities of the brake are also calculated.

The modern luxurious electric vehicle (EV) demands high torque and high-speed requirements with increased range. Fulfilling these requirements gives rise to the need for increased efficiency and power density of the motors in the Electric Drive Unit (EDU). Internal Permanent Magnet (IPM) motor is one of the best suited options in such scenarios because of its primary advantages of higher efficiency and precise control over torque and speed. In the IPM motor, permanent magnets are mounted within the rotor body to produce a resultant rotating magnetic field with the 3-phase AC current supply in the stator. IPM configuration provides structural integrity and high dynamic performance as the magnets are inserted within the rotor body. Adhesive glue is used to install the magnets within the laminated stack of rotor.