Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Wall Heat Flux on Impinging Diesel Spray Flame: Effect of Hole Size and Rail Pressure under Similar Injection Rate Condition

2020-10-30
2020-32-2313
The fuel economy of recent small size DI diesel engines has become more and more efficient. However, heat loss is still one of the major factors contributing to a substantial amount of energy loss in engines. In order to a full understanding of the heat loss mechanism from combustion gas to cylinder wall, the effect of hole size and rail pressure under similar injection rate conditions on transient heat flux to the wall were investigated. Using a constant volume vessel with a fixed impingement wall, the study measured the surface heat flux of the wall at the locations of spray flame impingement using three thin-film thermocouple heat-flux sensors. The results showed that the characteristic of local heat flux and soot distribution was almost similar by controlling similar injection rate except for the small nozzle hole size with increasing injection pressure.
Technical Paper

Investigations on NOx and Smoke Emissions Reduction Potential through Diesel-Water Emulsion and Water Fumigation in a Small Bore Diesel Engine

2020-10-30
2020-32-2312
In the present work, a relative comparison of addition of water to diesel through emulsion and fumigation methods is explored for reducing oxides of nitrogen (NOx) and smoke emissions in a production small bore diesel engine. The water to diesel ratio was kept the same in both the methods at a lower concentration of 3% by mass to avoid any adverse effects on the engine system components. The experiments were conducted at a rated engine speed of 1500 rpm under varying load conditions. A stable water-diesel emulsion was prepared using a combination of equal proportions (1:1 by volume) of Span 80 and Tween 80. The mixture of Span 80 in diesel and Tween 80 in water was homogenized using an IKA Ultra Turrax homogenizer with tip stator diameter 18mm at 5000 rpm for 2 minutes. The water-in-diesel emulsions thus formulated were kinetically stable and appeared translucent. No phase separation was observed on storage for approximately 105 days.
Technical Paper

Further Development of Particulate Sensors for Mobile Use with the Aid of a Circuit Board

2020-10-05
2020-01-1638
In the last decade, pollution by particulate matter and its effect on human health has increasingly become the focus of public attention. In order to monitor and evaluate particulate pollution, expensive measuring stations were placed at traffic hotspots and other selected locations. The measuring devices often precisely record the particle concentration, but have disadvantages in mobility and for measurements in large-area due to their size and investment costs. A measurement with high temporal and spatial resolution is not possible with these stations. This paper presents a new type of mobile particulate sensor based on the Plantower PMS 7003 particle sensor. In addition to the Plantower sensor, a rechargeable battery and newly developed control electronics are also installed in the particulate sensor. Due to the small size and the low manufacturing costs of the measuring system, mobile usage in higher quantity is possible.
Technical Paper

Usage of Low-Cost Particulate Matter Sensors for Characterization of Emission Dynamics at a Traffic Intersection and for the Description of Pollution in Urban Areas

2020-10-05
2020-01-1636
Despite the increase in public attention to particulate matter emissions since the millennium and the known effects on the human organism, representative predictions on the dispersion of emissions in both urban and rural areas are hardly possible so far. Especially the validation of simulations with measurement results is not possible due to the limited number and high price of certified measuring instruments. Rather, the temporally high-resolution measuring instruments are only sporadically distributed within the city, so that emission dynamics at traffic hotspots, such as traffic jams or intersections, cannot be depicted. Furthermore, due to the small number of certified measuring instruments, fine dust pollution can only be interpolated over long distances. In this paper, first statements about the transport characteristics of particles at a road intersection will be made by using a variety of so-called low-cost particulate matter sensors.
Technical Paper

Enclosure-In-Chamber Setup to Achieve Near-Zero Background Concentrations for Brake Emissions Testing

2020-10-05
2020-01-1634
Measuring brake emission is still a challenging non-standardized task. Extensive research is ongoing. Updates of work in progress are presented at SAE Brake Colloquium and PMP meetings. However, open items include how to achieve lower background concentration and how to design the brake enclosure. A low background concentration is essential as brake events are short and some emit in the range of reported background levels. Hence these emissions are difficult to distinguished from the background level. Even more critical, a high background concentration can result in a wrong particle number emissions value, either overestimated, background counted as emissions, or underestimated, background level subtracted, and low emission events no longer detected and counted. However, reducing the background level to less than 100 #/cm³ appeared to be quite challenging.
Technical Paper

Comparison of Particulate Matter and Number Emissions from a Floating and a Fixed Caliper Brake System of the Same Lining Formulation

2020-10-05
2020-01-1633
The particulate emissions of two brake systems where characterized in a dilution tunnel optimized for PM10 measurements. The larger of them employed a fixed caliper (FXC) and the smaller one a floating caliper (FLC). Both used ECE brake pads of the same lining formulation. Measured properties included gravimetric PM2.5 and PM10, Particle Number (PN) concentrations of both untreated and thermally treated (according to exhaust number regulation) particles using Condensation Particle Counters (CPCs) having 23 and 10 nm cut-off sizes, and an Optical Particle Sizer (OPS). The brakes were tested over a novel test cycle developed from the database of the Worldwide harmonized Light-Duty vehicles Test Procedure (WLTP). A series of WLTP tests were performed starting from unconditioned pads, to characterize the evolution of emissions until their stabilization. Selected tests were also performed over a short version of the Los Angeles City Cycle.
Technical Paper

Potentials and Challenges of a Brake Particle Emission Collecting System

2020-10-05
2020-01-1635
Brake particle emissions as a part of non-exhaust emissions are becoming more and more relevant, various international research activities can be stated. Also from the legislation side, first hints are given in regards of possible regulations. One possible approach for the reduction of brake particle emissions deals with the collection of those particles close to the foundation brake. The presented paper will follow such an approach and give some insights. In a first step, the technical layout is described for bench and vehicle testing. While for bench testing a PMP-like style of the setup could be chosen, the vehicle test setup is oriented on conventional wheel dust measurements. Hence, presented results of laboratory testing are dealing with PN and PM measurements. Also the impact on particle size distribution is discussed. It can be stated, that the particle collecting system is able to improve PN and PM emissions. Additionally, ultra-fine particles are almost eliminated.
Technical Paper

A Generic Testbody for Low-Frequency Aeroacoustic Buffeting

2020-09-30
2020-01-1515
Raising demands towards lightweight design paired with a loss of originally predominant engine noise pose significant challenges for NVH engineers in the automotive industry. From an aeroacoustic point of view, low frequency buffeting ranks among the most frequently encountered issues. The phenomenon typically arises due to structural transmission of aerodynamic wall pressure fluctuations and/or, as indicated in this work, through rear vent excitation. A possible workflow to simulate structure-excited buffeting contains a strongly coupled vibro-acoustic model for structure and interior cavity excited by a spatial pressure distribution obtained from a CFD simulation. In the case of rear vent buffeting no validated workflow has been published yet. While approaches have been made to simulate the problem for a real-car geometry such attempts suffer from tremendous computation costs, meshing effort and lack of flexibility.
Technical Paper

Experimental Investigation on the Effects of Cooled Low Pressure EGR and Water Injection on Combustion of a Turbocharged GDI Engine

2020-09-27
2020-24-0003
This work focuses on the effects of cooled Low Pressure EGR and Water Injection observed by conducting experimental tests consisting mainly of Spark Advance sweeps at different cooled LP-EGR and WI rates. The implications on combustion and main engine performance indexes are then analysed and modelled with a control-oriented approach, showing that combustion duration and phase and exhaust gas temperature are the main affected parameters. Results show that cooled LP-EGR and WI have similar effects, being the associated combustion speed decrease the main cause of exhaust gas temperature reduction. Experimental data is used to identify control-oriented polynomial models able to capture the effects of LP-EGR and WI on both these aspects. The limitations of LP-EGR are also explored, identifying maximum compressor volumetric flow and combustion stability as the main ones.
Technical Paper

On the Effects of Turbocharger on Particle Number and Size Distribution in a Heavy - Duty Diesel Engine

2020-09-27
2020-24-0007
Particles emitted from internal combustion engines have adverse health effects and the severity varies based on the particle size. A diesel particulate filter (DPF) in the after-treatment systems is employed to control the particle emissions from combustion engines. The design of a DPF depends on the nature of particle size distribution at the upstream and is important to evaluate. In heavy-duty diesel engines, the turbocharger turbine is an important component affecting the flow and particles. The turbine wheel and housing influence particle number and size. This could potentially be used to reduce particle number or change the distribution to become more favourable for filtration. This work evaluates the effect of a heavy-duty diesel engine’s turbine on particle number and size distribution.
Technical Paper

A Simulation Study Assessing the Viability of Shifting the Location of Peak In-Cylinder Pressure in Motored Experiments

2020-09-27
2020-24-0009
Hybrid powertrains utilize an engine to benefit from the power density of the liquid fuel to extend the range of the vehicle. On the other hand, the electric machine is used for; transient operation, for very low loads and where legislation prohibits any gaseous and particulate emissions. Consequently, the operating points of an engine nowadays shifted from its conventional, broad range of speed and load to a narrower operating range of high thermal efficiency. This requires a departure from conventional engine architecture, meaning that analytical models used to predict the behavior of the engines early in the design cycle are no longer always applicable. Friction models are an example of sub-models which struggle with previously unexplored engine architectures. The “pressurized motored” method has proven to be a simple experimental setup which allows a robust FMEP determination against which engine friction simulation can be fine-tuned.
Technical Paper

Ergonomic Study of Occupant Seating Using Near-Vertical Posture for Shared Mobility Applications

2020-09-25
2020-28-0519
Transportation system is at the brink of revolution and many new ways of mobility are arising in the market to ease the pressure on the established transportation infrastructure. Many companies and governments around the world are exploring innovative options in the space of shared mobility to reduce the overall carbon footprint. To expedite the adoption of shared mobility in India, it is necessary to make such options comfortable and cost-effective. One of the most effective way to make shared mobility options cost effective is to comfortably increase occupancy per vehicle footprint. This paper aims to evaluate a novel method of occupant seating to identify the maximum number of passengers a vehicle can accommodate without significant impact on occupant comfort. It is assumed that shared mobility options are used for a short duration of commute, and hence the comfort of the seat can be marginally compromised to increase the total number of occupants.
Technical Paper

Influence of Injection Parameters on Performance and Emission of DI Diesel Engine Fuelled by 1,4-Dioxane Emulsified Fuel

2020-09-25
2020-28-0518
The pattern of utilizing the water/diesel emulsion fuels in engines had been given great importance due to its ecological and exhaustion of petroleum reserves. This investigation displays the impact of 1,4-dioxane emulsified fuel on performance and emissions at various operating pressures. 1,4-dioxane emulsified fuel (DWSD10) was prepared with 10% 1,4-dioxane, 10% water, 0.2% surfactant and 79.8% diesel. To estimate the engine performance and emissions, the engine was operated with 180 bar, 200 bar and 220 bar operating pressures and the output was equated with diesel fuel operating on normal pressure of 200 bar. BTE of 1,4-dioxane emulsified fuel at 220 bar was higher when compare with diesel fuel. CO, HC and BSEC were lower at 220 bar on par with diesel fuel. However, NOx was increases for the higher operating pressure. Overall, except NOx, at higher injection pressure (@220 bar) the 1,4-dioxane emulsified fuel outperforms the diesel fuel in terms of emission and performance.
Technical Paper

Investigations on the Effect of Synchronizer Strut Detent Groove Profile on Static and Dynamic Gear Shift Quality of a Manual Transmission

2020-09-25
2020-28-0319
Automotive manufacturers are constantly working towards enhancing the driving experience of the customers. In this context, improving the static and dynamic gear shift quality plays a major role in ensuring a pleasant and comfortable driving experience. Moreover, the gear shift quality of any manual transmission is mainly defined by the design of the synchronizer system. The synchronizer sleeve strut detent groove profile plays a vital role in defining the performance of the synchronizer system by generating the minimum required pre-synchronization force. This force is important to move the outer synchronizer ring (blocker ring) to the required index position and to wipe-out the oil from the conical friction surfaces to build rapid high cone torque. Both these functional requirements are extremely critical to have a smooth and quick synchronization of the rotating parts under dynamic shift conditions.
Technical Paper

Experimental and Numerical Investigation of Contact Pressure Existence in Sealing Structure

2020-09-25
2020-28-0343
Sealing is one of the important components in the automotive and aerospace industry. The primary function of the lip seal is to protect contamination and retaining the lubricant. This investigation relates to a study of contact pressure existence on sealing structure between there mating region. Sealing for steering intermediate shaft should sustain sliding motion between shaft and seal as well as protection of lubricant from contamination and retention. Contact pressure analysis of Steering intermediate shaft with hyper elastic rubber seal is done at static condition using ABAQUS. Experiments were also conducted to check contact pressure between seal and shaft by using Fuji-pressure film sensor. The result from CAE analysis was compared with experimental data with 75% of the correlation with respect to CAE. This analysis of contact pressure helps to support on giving enough interference between seal and shaft which satisfies the need of sealing for an intermediate shaft.
Technical Paper

The Effect of TiB2 on Mechanical and Microstructural Properties of AZ91 Matrix Composites Manufactured by Cold Chamber Die Casting Process

2020-09-25
2020-28-0425
In these work AZ91 magnesium matrix composites reinforced with two weight fractions (5 and 10 wt. %) of TiB2 particulates were fabricated by cold chamber die casting process technique. The microstructure, density, hardness, mechanical properties of the specimens was investigated. Microstructure studies showed that fairly uniform distribution of reinforcements was achieved up to the weight fraction studied. As compared to base alloy AZ91, the hardness and tensile strength considerably increased with increasing reinforcement content. The presence of TiB2 particles improved the hardness around 24.4 %, compressive strength around 67.2% and the yield strength around 20%. The enormous amount of increment in the compressive strength due to the dislocation density created by the difference in thermal properties of matrix and composites and also due to the micro-pores presence in the composite.
Technical Paper

Modular Design and Analyze of Air Intake Manifold for Formula Vehicle

2020-09-25
2020-28-0485
The SAE formula student car organization constrained a rule to place a restrictor of diameter 20mm in between the throttle body and the engine inlet. The restrictor is a component that reduces and regulates the mass flow of air into the engine inlet. For this, a venture nozzle will be used as a restrictor in a vehicle to decrease the air pressure and increase the velocity in the intake manifold. Our proposed work aims to minimize the pressure drop by changing the convergent and divergent angles in the restrictor. For this by using solidworks eight various combinations of models with convergent angle as 13, 15 degrees, and divergent angle as 5,7 degrees was designed and analyzed using CFD fluent in ansys work bench. In this, 13 degree as convergent and 5 degree as a divergent model was found to have laminar airflow throughout with optimum pressure drop. The plenum is a large duct that equalizes the pressure drop caused by the restrictor in order to improve the efficiency of the engine.
Technical Paper

Modeling and Simulation of a Fighter Aircraft Cabin Temperature Control System Using AMESim

2020-09-25
2020-28-0497
Environmental Control System (ECS) of an aircraft is a complex system which operates classically in an air standard refrigeration cycle. ECS controls the temperature, pressure and flow of supply air to the cockpit, cabin or occupied compartments. The air cycle system of ECS takes engine bleed air as input. Parameters like bleed air pressure and temperature, mass flow, the external factors like ambient temperature, pressure, and aircraft attitude affect the performance of ECS to a large extent especially during transient. So, it is very important to consider the transient characteristics of these parameters in the design stage itself in order to ascertain the dynamic response of the system. This paper explains in detail the importance of transient input characteristics during the detailed design of ECS. A typical temperature control scheme for combat aircraft ECS has been studied and modeled in LMS AMESim.
Standard

Aftermarket Wheels - Passenger Cars and Light Truck - Performance Requirements and Test Procedures

2020-09-23
WIP
J2530
This SAE Recommended Practice provides performance, sampling, and certifying requirements, test procedures, and marking requirements for aftermarket wheels intended for normal highway use on passenger cars, light trucks, and multipurpose passenger vehicles. For aftermarket wheels on trailers drawn by passenger cars, light trucks or multipurpose vehicles, see SAE J1204. These performance requirements apply only to wheels made of materials included in Table 1 and Table 2. New nomenclature and terms are added to clarify wheel constructions typically not used in OEM applications. The testing procedures and requirements are based on SAE standards listed in the references.
Standard

Heat Treatment of Parts in a Vacuum

2020-09-22
CURRENT
AMS2769D
This specification establishes the requirements and procedures for heat treating parts in vacuum/partial pressure and shall be used as a supplementary document to primary heat treating specifications as applicable.
X