Search Results

A linear parameter varying (LPV) reduced order model (ROM) is used to approximate the volume-averaged temperature of battery cells in one of the modules of the battery pack with varying mass flow rate of cooling fluid using uniform heat source as inputs. The ROM runs orders of magnitude faster than the original CFD model. To reduce the time it takes to generate training data, used in building LPV ROM, a divide-and-conquer approach is introduced. This is done by dividing the battery module into a series of mid-cell and end-cell units. A mid-cell unit is composed of a cooling channel sandwiched in between two half -cells. A half-cell has half as much heat capacity as a full-cell. An end-cell unit is composed of a cooling channel sandwiched in between full-cell and a half-cell. A mass flow rate distribution look-up-table is generated from a set of steady-state simulations obtained by running the full CFD model at different inlet manifold mass flow rate samples.

One of the best tools to explore complicated in-cylinder physics is computational fluid dynamics (CFD). In order to assess the accuracy and reliability of the CFD simulations, it is critical to perform validation studies over different engine operating conditions. Simulation-based design of SI engines requires predictive capabilities, where results do not need to be tuned for each operating condition. This requires the models adopted to simulate their respective engine physics to be reliable under a broad range of conditions. A detailed set of experimental data was obtained to validate the CFD predictions of SI engine combustion.

Gasoline Direct Injection (GDI) is a key technology in the automotive industry for improving fuel economy and performance of gasoline internal combustion engines. GDI engine performance and emission characteristics are mainly determined by the complex interaction of in-cylinder flow, mixture formation and subsequent combustion processes. In a GDI engine, mixture formation depends on spray characteristics. Spray evolution and mixture formation is critical to GDI engine operation. In this work, a multi-component surrogate fuel blend was used to represent the chemical and physical properties of the gasoline employed in the experimental engine tests. Multi-component spray models were also validated in this study against experimental spray injection measurements in a chamber. The spray-chamber data include spray-penetration lengths, transient spray velocities and droplet Sauter mean diameter (SMD) at different axial and radial distances from the spray tip, obtained using a PDPA system.

Battery thermal management for high power applications such as electrical/hybrid vehicles is crucial. Modeling is an indispensable tool to help engineers design better battery cooling systems. While Computational Fluid Dynamics (CFD) has been used quite successfully for battery thermal management, CFD models can be too large and too slow for repeated transient thermal analysis especially for a battery module or pack. An accurate but much smaller battery thermal model using a state space representation is proposed. The parameters in the state space model are extracted from CFD results. The state space model is then shown to provide identical results as those from CFD under transient power inputs. While a CFD model may take hours to run depending on the size of the problem, the corresponding state space model runs in seconds.

A commonly used physics based electrochemisty model for a lithium-ion battery cell was first proposed by professor Newman in 1993. The model consists of a tightly coupled set of partial differential equations. Due to the tight coupling between the equations and the 2d implementation due to the particle modeling, and thus called pseudo-2d in literature, numerically obtaining a solution turns out to be challenging even for a lot of commercial softwares. In this paper, the VHDL-AMS language is used to solve the set of equations. VHDL-AMS allows the user to focus on the physical modeling rather than numerically solving the governing equations. In using VHDL-AMS, the user only needs to specify the governing equations after spatial discretization. A simulation environment, which supports VHDL-AMS, can then be used to solve the governing equations and also provides both pre- and post- processing tools.

This paper presents the current state of a three-layer surface icing model for ice crystal icing risk assessment in aircraft engines, being developed jointly by Ansys and Honeywell to account for possible heat transfer from inside an engine into the flow path where ice accretion occurs. The bottom layer of the proposed model represents a thin metal sheet as a substrate surface to conductively transfer heat from an engine-internal reservoir to the ice layer. The middle layer is accretion ice with a porous structure able to hold a certain amount of liquid water. A shallow water film layer on the top receives impinged ice crystals. A mass and energy balance calculation for the film determines ice accretion rate. Water wicking and recovery is introduced to transfer liquid water between film layer and porous ice accretion layer.

Cylinder head design is one of the most involved disciplines in engine design. Whether designing an altogether new head or revamping an old one, several different coupled and inter-dependent technologies ranging from heat transfer, fluid flow, combustion, material non-linearity, structural and fatigue have to be accounted. Simultaneous designing of ports, jacket and combustion chamber leads to cylinder head design, which is then tested for its strength and durability. Traditionally a series of analytical, empirical, test-based and simulation based exercises are conducted to design cylinder heads. With increasing pressure on reducing cost and turnaround time, focus on moving towards a quasi-simulation based design and development of cylinder heads is gaining strength. This paper talks about how a simulation driven process for cylinder head design can be developed.

Due to growing interest in hybrid and electric vehicles, li-ion battery modeling is receiving a lot of attention from designers and researchers. This paper presents a complete model for a li-ion battery pack. It starts from the Newman electrochemistry model to create the battery performance curves. Such information is then used for cell level battery equivalent circuit model (ECM) parameter identification. 28 cell ECMs are connected to create the module ECM. Four module ECMs are connected through a busbar model to create the pack ECM. The busbar model is a reduced order model (ROM) extracted from electromagnetic finite element analysis (FEA) results, taking into account the parasitic effects. Battery thermal performance is simulated first by computational fluid dynamics (CFD). Then, a thermal linear and time-invariant (LTI) ROM is created out of CFD solution. The thermal LTI ROM is then two-way coupled with the battery pack ECM to form a complete battery pack model.

The thermal behavior of a fluid-cooled battery can be modeled using computational fluid dynamics (CFD). Depending on the size and complexity of the battery module and the available computing hardware, the simulation can take days or weeks to run. This work introduces a reduced-order model that combines proper orthogonal decomposition, capturing the variation of the temperature field in the spatial domain, and linear time-invariant system techniques exploiting the linear relationship between the resulting proper orthogonal decomposition coefficients and the uniform heat source considered here as the input to the system. After completing an initial CFD run to establish the reduction, the reduced-order model runs much faster than the CFD model. This work will focus on thermal modeling of a single prismatic battery cell with one adjacent cooling channel. The extension to the multiple input multiple output case such as a battery module will be discussed in another paper.

The safety, performance, and operational life of power dense Lithium-ion batteries used in Hybrid and Electric Vehicles are dependent on the operating temperature. Modeling and simulation are essential tools used to accelerate the design process of optimal thermal management systems. However, high-fidelity 3D computational fluid dynamics (CFD) simulation of such systems is often difficult and computationally expensive. In this paper, we demonstrate a multi-part coupled system model for simulating the heating/cooling system of the traction battery at a module level. We have reduced computational time by employing reduced-order modeling (ROM) framework on separate 3D CFD models of the battery module and the cooling plate. The order of the thermal ROM has also been varied to study the trade-off between accuracy, fidelity, and complexity. The ROMs are bidirectionally coupled to an empirical battery model built from in-house test data.

With the rapid development of electric vehicles, the demands for lithium-ion batteries and advanced battery technologies are growing. Today, lithium-ion batteries mainly use liquid electrolytes, containing organic compounds such as dimethyl carbonate and ethylene carbonate as solvents for the lithium salts. However, when thermal runaway occurs, the electrolyte decomposes, venting combustible gases that could readily be ignited when mixed with air and leading to pronounced heat release from the combustion of the mixture. So far, the chemical behavior of electrolytes during thermal runaway in lithium-ion batteries is not comprehensively understood. Well-validated compact chemical kinetic mechanisms of the electrolyte components are required to describe this process in CFD simulations. In this work, submechanisms of dimethyl carbonate and ethylene carbonate were developed and adopted in the Ansys Model Fuel Library (MFL).