Search Results

The increasing numbers of hybrid electric and full electric vehicle models currently in the market or in the pipeline of automotive OEMs require creative testing mechanisms to drive down development costs and optimize the efficiency of these vehicles. In this paper, such a testing mechanism that has been successfully implemented at the US Environmental Protection Agency National Vehicle and Fuel Emissions Laboratory (EPA NVFEL) is described. In this testing scheme, the units-under-test consist of a battery pack and its associated battery management system (BMS). The remaining subsystems, components, and environment of the vehicle are virtual and modeled in high fidelity.

Engine dynamometer testing was performed comparing fuels having different octane ratings and ethanol content in a Ford 3.5L direct injection turbocharged (EcoBoost) engine at three compression ratios (CRs). The fuels included midlevel ethanol “splash blend” and “octane-matched blend” fuels, E10-98RON (U.S. premium), and E85-108RON. For the splash blends, denatured ethanol was added to E10-91RON, which resulted in E20-96RON and E30-101 RON. For the octane-matched blends, gasoline blendstocks were formulated to maintain constant RON and MON for E10, E20, and E30. The match blend E20-91RON and E30-91RON showed no knock benefit compared to the baseline E10-91RON fuel. However, the splash blend E20-96RON and E10-98RON enabled 11.9:1 CR with similar knock performance to E10-91RON at 10:1 CR. The splash blend E30-101RON enabled 13:1 CR with better knock performance than E10-91RON at 10:1 CR. As expected, E85-108RON exhibited dramatically better knock performance than E30-101RON.

This paper describes development challenges for Heavy-Duty (HD) on-highway Diesel Direct Injection (DDI™) engines to meet the extremely advanced US-EPA 2010 (later named US 2010) emission limits while further increasing power density in combination with competitive engine efficiency. It discusses technologies and solutions for lowest engine-out emissions in combination with most competitive fuel consumption values and excellent dynamic behavior. To achieve these challenging targets, base engine hardware requirements are described. In detail the development of EGR systems, especially the challenges of running high EGR rates over the whole engine speed range also at high load, the dynamic EGR control for transient engine operation to achieve lowest NOx emissions at the smoke limit with excellent load response is discussed. Also the effect of the turbo-machinery on power density and transient engine behavior is shown.

In order to improve the accuracy of vehicle simulation under transient cycle conditions and thus predict performance and fuel consumption, consideration of the complete system engine/drivetrain/vehicle is necessary. The coupling of otherwise independent simulation programs is therefore necessary for the vehicle and engine. The description of thermally transient processes enables the calculation of the heat balance of the engine, which in turn enables the simulation of warming up operation. Through consideration of the engine warming up process, the quality of the prediction of fuel consumption and emissions is improved. The combination of the simulation programs CRUISE and BOOST to determine the engine heat balance has proven to be successful for the analysis of transient drive cycles.

With the implementation of EURO VI and similar emission legislation, the industry assumed the pace and stringency of new legislation would be reduced in the future. The latest announcements of proposed and implemented legislation steps show that future legislation will be even more stringent. The currently leading announced legislation, which concerns a large number of global manufacturers, is the legislation from the United States (US) Environmental Protection Agency (EPA) and the California Air Resources Board (CARB). Both announced new legislation for CO2, Greenhouse Gas (GHG) Phase II. CARB is also planning additional Ultra Low NOx regulations. Both regulations are significant and will require a number of technologies to be used in order to achieve the challenging limits. AVL published some engine related measures to address these legislation steps.

The cost of fuel for commercial trucks is second only to labor in the total vehicle operating costs. Therefore, technologies that reduce fuel consumption can have a significant impact on the bottom line for both trucking fleets and owner/operators. Quantifying the fuel savings associated with different technologies, however, is complicated by many factors, and short-term testing often cannot adequately quantify small changes in fuel consumption that, over time, can add up to substantial cost savings on a vehicle. For example, fuel economy gains of less than one percent may not be reliably measurable using fuel tests, and variable environmental and use factors can cast some doubt on the appropriateness of short-term testing.

It has been previously reported that ethanol can be reformed at around 300°C to a mixture of hydrogen, carbon monoxide, and methane using copper-plated nickel catalyst. This low reforming temperature enables heat to be supplied from the engine exhaust. Single-cylinder engine testing demonstrated that this gaseous mixture of "ethanol reformate" enhances engine combustion and part load dilution capability, which decreases fuel consumption while also reducing feedgas NOx emissions. In addition, excellent cold start capability with significantly reduced hydrocarbon emissions was observed. Thus, ethanol reformate has the potential to address two major barriers to wider use of ethanol as an engine fuel: ethanol's low heating value per volume and higher hydrocarbon emissions at startup relative to gasoline. In this study, the dilute capability of a multi-cylinder engine was assessed using a mixture of 50% reformate and 50% E85 on a mass basis at several key part load operating points.

Future legislation scenarios as well as stringent CO2 targets, in particular under real driving conditions, will require the introduction of new and additional powertrain technologies. Beside the increasing electrification of the powertrain, it will be essential to utilize the full potential of the Internal Combustion Engine (ICE). There is clearly a competition of new and different ICE-Technologies [1] including VCR. VCR systems are expected to be introduced to a considerable number of next generation turbocharged Spark Ignited (SI) engines in certain vehicle classes. The implementation of Miller or Atkinson cycles is an essential criterion for increased geometric Compression Ratio (CR). The DUAL MODE Variable Compression System (VCS)TM enables a 2-stage variation of the connecting rod length and thus of the compression ratio (CR).

Increasing powertrain complexity and the growing number of vehicle variants are putting a strain on current calibration development processes. This is particularly challenging for vehicle drivability calibration, which is traditionally completed late in the development cycle, only after mature vehicle hardware is available. Model-based calibration enables a shift in development tasks from the real world to the virtual world, allowing for increased system robustness while reducing development costs and time. A unique approach for drivability calibration was developed by incorporating drivability analysis software with online optimization software into a virtual engine test cell environment. Real-time, physics-based engine and vehicle simulation models were coupled with real engine controller hardware and software to execute automated drivability calibration within this environment.

This paper outlines the characterization of a Li-Ion Iron Phosphate battery pack with nominal voltage of 700V as well as the modeling of this pack as an equivalent electrical circuit (EEC) for the purpose of vehicle simulations. For a higher level of fidelity and accuracy, the equivalent circuit is initially modeled as an R-2RC circuit which consists of a voltage source with one resistor (R) and two resistor-capacitor (RC) branches. In this modeling effort, first, several open circuit voltage (OCV) determination methods in the literature are benchmarked and state-of-charge (SOC) dependent OCV curve which is used in the voltage source of the EEC model is derived. Then, two methods of parameter estimation of the EEC are developed for both step current and dynamic current profiles. The first estimation method is applicable to discharge or charge step currents and relies mostly on the relaxation portion of the battery response and involves some manual calibration.