Search Results

This paper studies the effects of various types of parking brake cable construction on parking brake system efficiency. Testing was conducted on a variety of common cable constructions from several industry sources. Cable construction variables include different types of conduit and wire strand. Input travel, input force, output travel, and output force were carefully measured under controlled conditions. Force, travel and hence work efficiencies were calculated and analyzed to identify any differences that might exist under the defined test conditions. Conclusions were drawn that might provide direction for improving parking brake system designs that have performance issues caused by poor cable efficiency.

Torsional vibration dampers are used in automatic and manual transmissions to provide passenger comfort and reduce damage to transmission & driveline components from engine torsionals. This paper will introduce a systematic method to model a torque converter (TC) arc spring damper system using Simdrive software. Arc spring design parameters, dynamometer (dyno) setup, and complete powertrain/driveline system modeling and simulation are presented. Through arc spring dynamometer setup subsystem modeling, the static and dynamic stiffness and hysteresis under different engine loads and engine speeds can be obtained. The arc spring subsystem model can be embedded into a complete powertrain/driveline model from engine to wheels. Such a model can be used to perform the torsional analysis and get the torsional response at any location within the powertrain/driveline system. The new methodology enables evaluation of the TC damper design changes to meet the requirements.

During the vehicle development process, dimensional variation simulation modeling has been applied extensively to estimate the effects of build variation on the final product. Traditional variation simulation methods analyze the tolerance inputs of structural components, but do not account for any compliance effects due to stiffness variation in tuning components, such as bushings, springs, isolators, etc., since both product and process variation are simulated based on rigid-body assumptions. Vehicle performance objectives such as ride and handling (R&H) often involve these compliance metrics. The objective of this paper is to present a method to concurrently simulate the tolerance from the structural parts as well as the variability of compliance from the tuning components through an integration package. The combination of these two highly influential effects will allow for a more accurate prediction and assessment of vehicle performance.

It is customary to select a twist beam rear suspension for front wheel driven small and medium range passenger cars. Besides better primary / secondary ride comfort, roll stiffness tuning ability, ease of assembly & good packaging solutions than the conventional semi trailing arm/ rigid axle suspensions, twist beam suspension system accentuate the concentration required in placing & orienting the cross beam to achieve certain imperative kinematical characteristics. In order to make the solutions of the required kinematical targets viable, it is vital to have the packaging space and stress concentration within yield limits given the weight & cost targets. This paper presents the work done on twist beam type suspension for a new generation entry level B-Class hatchback vehicle developed. To reduce the time consumed in validation of different design proposals a virtual validation process was developed.

In an environment of tougher engineering constraints to deliver tomorrow's aerodynamic vehicles, evaluation of aerodynamics early in the design process using digital prototypes and simulation tools has become more crucial for meeting cost and performance targets. Engineering needs have increased the demands on simulation software to provide robust solutions under a range of operating conditions and with detailed geometry representation. In this paper the application of simulation tools to wheel design in on-road operating conditions is explored. Typically, wheel and wheel cover design is investigated using physical tests very late in the development process, and requires costly testing of many sets of wheels in an on-road testing environment (either coast-down testing or a moving-ground wind-tunnel).

The brake system is one of the most critical systems in the automotive vehicle. Its design is a challenging task since stringent performance and packaging requirements are to be fully met - optimizing the brake performance and weight of the brake system. The brake disc is an important component in the braking system which is expected to withstand and dissipate the heat generated during the braking event. Validation of brake disc design through CAE/FEA is presented in this paper. The procedure for prediction of thermal performance was developed in-house, tuned and verified by correlating with Test data available for existing-design and then applied to the new-design brake disc. The correlation achieved for the existing-design brake disc (both solid and ventilated), procedure for prediction of thermo-mechanical performance (heat transfer coefficient estimation, temperature distribution etc.) are also included.

Road-tire induced vibrations are in many vehicles determining the interior noise levels in (semi-) constant speed driving. The understanding of the noise contributions of different connections of the suspension systems to the vehicle is essential in improvement of the isolation capabilities of the suspension- and body-structure. To identify these noise contributions, both the forces acting at the suspension-to-body connections points and the vibro-acoustic transfers from the connection points to the interior microphones are required. In this paper different approaches to identify the forces are compared for their applicability to road noise analysis. First step for the force identification is the full vehicle operational measurement in which target responses (interior noise) and indicator responses (accelerations or other) are measured.

This paper presents a process for the selection of spring rate and pre-load for an adaptively controlled pivoting vane oil pump. The pivoting vane pump has two modes: high and low speed. A spring within the pump is installed to induce a torque that causes an adaptive displacement mechanism within the pump to move toward maximum oil chamber size. In low speed mode, two feedback regions are pressurized that produce torques that counter the spring generated torque. Together, both regions being pressurized by main oil gallery pressure tend to reduce pump displacement more at lower speeds than if only a single chamber is pressurized. At higher speeds, a solenoid switch turns off pressure to one of the feedback pressure chambers, thereby reducing feedback torque that counters spring torque. This enables higher pressure calibrations in this speed mode. In this paper, we identify a process for choosing the spring rate and pre-load that calibrates the adaptive displacement mechanism.

Engine Stop/Start System (ESS) promises to reduce greenhouse emissions and improve fuel economy of vehicles. Previous work of the Authors was concentrated on bridging the gap of improvement in fuel economy promised by ESS under standard laboratory conditions and actual driving conditions. Findings from the practical studies lead to a conclusion that ESS is not so popular among the customers, due to the complexities of the system operation and poor integration of the system design with the driver behavior. In addition, due to various functional safety requirements, and traffic conditions, actual benefits of ESS are reduced. A modified control algorithm was proposed and proven for the local driving conditions in India. The ways in which a given driver behaves on the controls of the vehicles like Clutch and Brake Pedals, Gear Shift Lever were not uniform across the demography of study and varied significantly.

Brake judder is a brake induced vibration that a vehicle driver experiences in the steering wheel or floor panel at highway speeds during vehicle deceleration. The primary cause of this disturbance phenomenon is the brake torque variation (BTV). Virtual CAE tools from both kinematics and compliance standpoints have been applied in analyzing sensitivities of the vehicle systems to BTV. This paper presents a recently developed analytical approach that identifies parameters of steering and suspension systems for achieving optimal settings that desensitize the vehicle response to BTV. The analytical steps of this integrated approach started with creating a lumped mass noise-vibration-harshness (NVH) control model and a separate multi-body dynamics (MBD) suspension model. Then, both models were linked to run in a sequence through optimization software so the results from the MBD model were used as quasi-static inputs to the lumped mass NVH model.

Pneumatic brake system is widely used in heavy truck, medium and heavy buses for its great superiority and braking performance over other brake systems. Pneumatic brake system consists of various valves such as Dual Brake Valve (DBV), Quick release Valve (QRV), Relay Valve (RV), Brake chambers. Dynamics of each valve is playing a crucial role in overall dynamic performance of the braking system. However, it is very difficult to find the contribution of each valve and pipe diameters in overall braking performance. Hence, it is very difficult to arrive a best combination for targeted braking performance as it is not possible to evaluate all combination on the actual vehicle. Hence, it is very important to have a mathematical model to optimize and evaluate the overall braking performance in early design phase. The present study is focusing on the mathematical model of a pneumatic brake circuit.

Today urban buses are equipped with more air consuming devices for an example pneumatic doors, exhaust brake, air suspension and in SCR system to name a few. This has resulted in higher air demand leading to high compressor duty cycles which cause conditions (such as higher compressor head temperatures) that may adversely affect air brake charging system performance. These conditions may require additional maintenance due to a higher amount of oil vapor droplets being passed along into the air brake system. Factors that add to the duty cycle are air suspension, additional air accessories, use of an undersized compressor, frequent stops, excessive air leakage from fittings, connections, lines, chambers or valves, etc. This paper discussed about methodology used to reduce air consumption of air consuming devices used in urban bus application. Performance assessment of air consuming devices with minimum available air pressure was conducted and found satisfactory.

Error in suspension asymmetry or tire parameters may lead to vehicle drifting laterally from its intended straight-line path, which is called vehicle pull. Driver then needs to apply constant steering correction to maintain the vehicle in straight line which will lead to high driver fatigue and deteriorate driving experience. Manufacturing a perfectly symmetric suspension system is impractical, however an insight into the manufacturing tolerances of suspension system at the early design stage can be extremely useful. Also tire force and moment parameters at straight line operation and its maximum allowable variations will help in defining the tire parameter specifications and tolerances. The objective of this study was to develop a 1D model of suspension and tire system which can predict the torque experienced in steering and drift of the vehicle from straight line due to the tire force and moment and asymmetric suspension geometry.

In electric power assisted steering system (EPAS), the steering assistance torque is provided by the electric motor. The motor rating is decided based on rack force requirement which depends on the vehicle weight, steering gear ratio, wheel angles etc. The load on the EPAS motor varies with respect to the steered angles of the road wheels. The motor experiences higher load towards the road wheel lock position. Most of the steering systems used on passenger cars has rack and pinion gear with constant gear ratio (C-factor). The constant gear ratio is decided to create right balance between vehicle handling behavior and steering effort. The constant gear ratio exerts higher steering load which the EPAS motor is required to support up to road wheel lock angles and hence EPAS motor size increases. This paper presents variable gear ratio (VGR) steering system in which gear ratio varies from center towards end lock stroke of rack & pinion.

Vehicle dynamics is one of the most important vehicle attributes. It is classified into three domains, the longitudinal, vertical, and lateral dynamics. This paper focuses on optimizing the lateral vehicle dynamics which is driven by the straight ahead controllability and cornering controllability of the vehicle. One of the important parameters that dictates these sub-attributes is the steering ratio. Therefore, designing the right steering ratio is critical to meet the vehicle “specific” targets. Significant amount of work has been done by many researchers on variable steering ratio by implementing variable gear ratio (VGR) rack, active steering, and steer-by-wire systems. This paper discusses the methodology and considerations to optimize the steering ratio for a constant gear ratio rack by optimizing the steering column layout, viz., orientation and the phase angle in universal joints.

Generic spindle loads are used in the upfront analysis for vehicle durability development. They represent different load case into the vehicle suspension system, such as potholes, cornering, and braking. The advantage of using these generic load cases is that they can be used upfront in the durability development process before hardware is available. The generic spindle loads are cascaded through the suspension system to generate component loads which can then be used for stress analysis. The paper describes a study that was done to determine the validity of current generic spindle loads by analyzing spindle data from multiple vehicles in the same class. The paper will explain the initial data analysis that was done, which was normalizing the spindle loads by weight. In addition, the paper will then go into further detail on describing a relationship between spindle loads and tire sidewall height, which reduced the load scatter.