Search Results

This article reports on the potential of negative valve overlap (NVO) for improving the net indicated thermal efficiency (η NIMEP) of gasoline engines during part load. Three fixed fuel flow rates, resulting in indicated mean effective pressures of up to 6 bar, were investigated. At low load, NVO significantly reduces the pumping loses during the gas exchange loop, achieving up to 7% improvement in indicated efficiency compared to the baseline. Similar efficiency improvements are achieved by positive valve overlap (PVO), with the disadvantage of worse combustion stability from a higher residual gas fraction (xr). As the load increases, achieving the wide-open throttle limit, the benefits of NVO for reducing the pumping losses diminish, while the blowdown losses from early exhaust valve opening (EVO) increase.

The fuel effects on throttle transients in PFI spark ignition engines were assessed through experiments with simultaneous step change of the throttle position from part load to WOT and increment of the injected fuel amount. The test matrix consisted of various gasoline/methanol blends from pure gasoline to pure methanol, coolant temperatures at 40C (for cold engine condition) and 80C (for warm engine), and different levels of fuel enrichment at the WOT condition. The x-τ model was used to interpret the engine GIMEP response in the transient. Using the model, a procedure was developed to calculate the parameters of the transient from the data. These parameters were systematically regressed against the fuel distillation points, the increment in injected fuel mass in the transient, and the enthalpy required to evaporate the fuel increment as the explanatory variables.

Throttle ramp rate effects on the in-cylinder fuel/air (F/A) excursion was studied in a production engine. The fuel delivered to the cylinder per cycle was measured in-cylinder by a Fast Response Flame Ionization detector. Intake pressure was ramped from 0.4 to 0.9 bar. Under slow ramp rates (∼1 s ramp time), the Engine Electronic Control (EEC) unit provided the correct compensation for delivering a stoichiometric mixture to the cylinder throughout the transient. At fast ramp rates (a fraction of a second ramps), a lean spike followed by a rich one were observed. Based on the actual fuel injected in each cycle during the transient, a x-τ model using a single set of x and τ values reproduced the cycle-to-cycle in-cylinder F/A response for all the throttle ramp rates.

This paper describes a post-race analysis of team KOMMIT EVT’s electric motorcycle data collected during the 2016 Pikes Peak International Hill Climb (PPIHC). The motorcycle consumed approximately 4 kWh of battery energy with an average and maximum speed of 107 km/h and 149 km/h, respectively. It was the second fastest electric motorcycle with a finishing time of 11:10.480. Data was logged of the motorcycle’s speed, acceleration, motor speed, power, currents, voltages, temperatures, throttle position, GPS position, rider’s heart rate and the ambient environment (air temperature, pressure and humidity). The data was used to understand the following factors that may have prevented a faster time: physical fitness of the rider, thermal limits of the motor and controller, available battery energy and the sprocket ratio between the motor and rear wheel.

An adaptive air/fuel ratio controller for SI engine throttle transient was developed. The scheme is based on an event- based, single- parameter fuel dynamics model. A least- square- error algorithm with an active forgetting factor was used for parameter identifications. A one- step- look- ahead controller was designed to maintain the desired air/fuel ratio by canceling the fuel dynamics with the controller setting updated adaptively according to the identified parameters. When implemented on a Ford Ztech engine and tested under a set of throttle- transient operations, the adaptive controller learned quickly and performed well.

THE thermodynamic analysis of an internal-combustion engine, even in the idealized case, is in general more complex than a similar analysis of an engine cycle in which the fluid undergoes no chemical change. It is the purpose of this paper to show that, despite the inherent complexity of the problem, an exact solution by graphical methods is possible, and the method is very similar in nature to those used in connection with the Mollier diagram for steam. Two types of charts are presented, one descriptive of the thermodynamic properties of the airfuel mixture (and residual products of combustion) before combustion, the other descriptive of the properties of the equilibrium mixture after combustion. Full allowance is made for the variation of specific heats with temperature and for the complex dissociation at the high temperatures attained after combustion. All calculations are based on the most recent basic thermodynamic data available in the literature.