Search Results

An experimental study was performed to develop a more fundamental understanding of the effects of secondary air injection (SAI) on exhaust gas emissions and catalyst light-off characteristics during cold start of a modern SI engine. The effects of engine operating parameters and various secondary air injection strategies such as spark retardation, fuel enrichment, secondary air injection location and air flow rate were investigated to understand the mixing, heat loss, and thermal and catalytic oxidation processes associated with SAI. Time-resolved HC, CO and CO₂ concentrations were tracked from the cylinder exit to the catalytic converter outlet and converted to time-resolved mass emissions by applying an instantaneous exhaust mass flow rate model. A phenomenological model of exhaust heat transfer combined with the gas composition analysis was also developed to define the thermal and chemical energy state of the exhaust gas with SAI.

Mechanisms of NH₃ generation using LNT-like catalysts have been studied in a bench reactor over a wide range of temperatures, flow rates, reformer catalyst types and synthetic exhaust-gas compositions. The experiments showed that the on board production of sufficient quantities of ammonia on board for SCR operation appeared feasible, and the results identified the range of conditions for the efficient generation of ammonia. In addition, the effects of reformer catalysts using the water-gas-shift reaction as an in-situ source of the required hydrogen for the reactions are also illustrated. Computations of the NH₃ and NOx kinetics have also been carried out and are presented. Design and impregnation of the SCR catalyst in proximity to the ammonia source is the next logical step. A heated synthetic-exhaust gas flow bench was used for the experiments under carefully controlled simulated exhaust compositions.

The effects of charge motion and laminar flame speeds on combustion and exhaust temperature have been studied by using an air jet in the intake flow to produce an adjustable swirl or tumble motion, and by replacing the nitrogen in the intake air by argon or CO₂, thereby increasing or decreasing the laminar flame speed. The objective is to examine the "Late Robust Combustion" concept: whether there are opportunities for producing a high exhaust temperature using retarded combustion to facilitate catalyst warm-up, while at the same time, keeping an acceptable cycle-to-cycle torque variation as measured by the coefficient of variation (COV) of the net indicated mean effective pressure (NIMEP). The operating condition of interest is at the fast idle period of a cold start with engine speed at 1400 RPM and NIMEP at 2.6 bar. A fast burn could be produced by appropriate charge motion. The combustion phasing is primarily a function of the spark timing.

Ammonia oxidation (AMOX) catalysts are critical parts of most diesel aftertreatment systems around the world. These catalysts are positioned downstream of selective catalytic reduction (SCR) catalysts and remove unreacted NH3 that passes through the SCR catalyst. In many configurations, the AMOX catalyst is situated after a diesel oxidation catalyst and catalyzed diesel particulate filter that oxidize CO and hydrocarbons. However, in Euro V and proposed Tier 4 final aftertreatment architectures there is no upstream oxidation catalyst. In this study, the impact of hydrocarbons is evaluated on two different types of AMOX catalysts. One has dual washcoat layers-SCR washcoat on top of PGM washcoat-and the other has only a PGM washcoat layer. Results are presented for NH3 and hydrocarbon oxidation, NOx and N2O selectivity, and hydrocarbon storage. The AMOX findings are rationalized in terms of their impact on the individual oxidation and SCR functions.

In this study, the formation and decomposition of ammonium nitrate (AN) on a state-of-the-art extruded vanadium-based SCR catalyst (V-SCR) under simulated exhaust conditions has been evaluated. Results show that AN readily forms and accumulates at temperatures below 200°C when exposed to NH3 and NO2. The rate of AN accumulation increases with decreasing temperature. A new low temperature NH3 release peak (not present following NH3 storage conditions with NH3 only) becomes apparent after AN accumulation at 100 and 125°C. This new NH3 release, with a peak release temperature of approximately 180°C, is evaluated in detail to better determine its origin. BET surface area, and thermal gravimetric analysis/differential scanning calorimetry (TGA/DSC), and reactor-based experiments are all used to characterize AN formed on the V-SCR catalyst in comparison to pure AN.

Lean-burn natural gas (NG) engines are used world-wide for both stationary power generation and mobile applications ranging from passenger cars to Class 8 line-haul trucks. With the recent introduction of hydraulic fracturing gas extraction technology and increasing availability of natural gas, these engines are receiving more attention. However, the reduction of unburned hydrocarbon emissions from lean-burn NG and dual-fuel (diesel and natural gas) engines is particularly challenging due to the stability of the predominant short-chain alkane species released (e.g., methane, ethane, and propane). Supported Pd-based oxidation catalysts are generally considered the most active materials for the complete oxidation of low molecular weight alkanes at temperatures typical of lean-burn NG exhaust. However, these catalysts rapidly degrade under realistic exhaust conditions with high water vapor concentrations and traces of sulfur.

The oxidation of short-chain alkanes, such as methane, ethane, and propane, from the exhaust of lean-burn natural gas and lean-burn dual-fuel (natural gas and diesel) engines poses a unique challenge to the exhaust aftertreatment community. Emissions of these species are currently regulated by the US Environmental Protection Agency (EPA) as either methane (Greenhouse Gas Emissions Standards) or non-methane hydrocarbon (NMHC). However, the complete catalytic oxidation of short-chain alkanes is challenging due to their thermodynamic stability. The present study focuses on the oxidation of short-chain alkanes by vanadium-based and Cu/zeolite selective catalytic reduction (SCR) catalysts, generally utilized to control NOx emissions from lean-burn engines. Results reveal that these catalysts are active for short-chain alkane oxidation, albeit, at conversions lower than those generally reported in the literature for Pd-based catalysts, typically used for short-chain alkane conversion.

To meet future particle mass and particle number standards, gasoline vehicles may require particle control, either by way of an exhaust gas filter and/or engine modifications. Soot levels for gasoline engines are much lower than diesel engines; however, non-combustible material (ash) will be collected that can potentially cause increased backpressure, reduced power, and lower fuel economy. The purpose of this work was to examine the ash loading of gasoline particle filters (GPFs) during rapid aging cycles and at real time low mileages, and compare the filter performances to both fresh and very high mileage filters. Current rapid aging cycles for gasoline exhaust systems are designed to degrade the three-way catalyst washcoat both hydrothermally and chemically to represent full useful life catalysts. The ash generated during rapid aging was low in quantity although similar in quality to real time ash. Filters were also examined after a low mileage break-in of approximately 3000 km.

Low-temperature (T ≤ 200°C) NOx conversion is receiving increasing research attention due to continued potential reductions in regulated NOx emissions from diesel engines. At these temperatures, ammonium salts (e.g., ammonium nitrate, ammonium (bi)sulfate, etc.) can form as a result of interactions between NH3 and NOx or SOx, respectively. The formation of these salts can reduce the availability of NH3 for NOx conversion, block active catalyst sites, and result in the formation of N2O, a regulated Greenhouse Gas (GHG). In this study, we investigate the effect of hydrothermal aging on the formation and decomposition of ammonium nitrate on a state-of-the-art Cu/zeolite selective catalytic reduction (SCR) catalyst. Reactor-based constant-temperature ammonium nitrate formation, temperature programmed oxidation (TPO), and NO titration experiments are used to characterize the effect of hydrothermal aging from 600 to 950°C.

Titanium dioxide supported vanadium oxide catalysts have been successfully utilized for the selective catalytic reduction (SCR) of nitrogen oxides emitted from both stationary and mobile sources. Because of their cost and performance advantages in certain applications, vanadium-based SCR catalysts are now also being considered for integration into some U.S. Tier IV off-highway aftertreatment systems. However, concern exists that toxic vanadium compounds, such as vanadium pentoxide, could be released from these catalysts as a result of mechanical attrition or high temperature volatility. An experimental study has been conducted to compare various techniques for measuring the release of particle and vapor-phase vanadium from SCR catalysts. Previous research has utilized a powder reactor-based method to measure the vapor-phase release of vanadium, but there are inherent limitations to this technique.

Selective catalytic reduction (SCR) of nitrogen oxides (NOx) is used in diesel-fueled mobile applications where urea is an added reducing agent. We show that the Ultera® dual-stage catalyst, with intercooling aftertreatment system, intrinsically performs the function of the SCR method in nominally stoichiometric gasoline vehicle engines without the need for an added reductant. We present that NOx is reduced during the low-temperature operation of the dual-stage system, benefiting from the typically periodic transient operation (acceleration and decelerations) with the associated swing in the air/fuel ratio (AFR) inherent in mobile applications, as commonly expected and observed in real driving. The primary objective of the dual-stage aftertreatment system is to remove non-methane organic gases (NMOG) and carbon monoxide (CO) slip from the vehicle’s three-way catalyst (TWC) by oxidizing these constituents in the second stage catalyst.

Natural gas-powered engines are widely used due to their low fuel cost and in general their lower emissions than conventional diesel engines. In order to comply with emissions regulations, an aftertreatment system is utilized to treat exhaust from natural gas engines. Stoichiometric burn natural gas engines use three-way catalyst (TWC) technology to simultaneously remove NOx, CO, and hydrocarbon (HC). Removal of methane, one of the major HC emissions from natural gas engines, is difficult due to its high stability, posing a challenge for existing TWC technologies. In this work, degreened (DG), standard bench cycle (SBC)-aged TWC catalysts and a DG Pd-based oxidation catalyst (OC) were evaluated and compared under a variety of lean/rich gas cycling conditions, simulating stoichiometric natural gas engine emissions.

This paper reviews the relevant literature on the effects of sulfated ash, phosphorus, and sulfur on DPF, LNT, and SCR catalysts. Exhaust backpressure increase due to DPF ash accumulation, as well as the rate at which ash is consumed from the sump, were the most studied lubricant-derived DPF effects. Based on several studies, a doubling of backpressure can be estimated to occur within 270,000 to 490,000 km when using a 1.0% sulfated ash oil. Postmortem DPF analysis and exhaust gas measurements revealed that approximately 35% to 65% less ash was lost from the sump than was expected based on bulk oil consumption estimates. Despite significant effects from lubricant sulfur and phosphorus, loss of LNT NOX reduction efficiency is dominated by fuel sulfur effects. Phosphorus has been determined to have a mild poisoning effect on SCR catalysts. The extent of the effect that lubricant phosphorus and sulfur have on DOCs remains unclear, however, it appears to be minor.

A novel engine management strategy for achieving fast catalyst light-off without the use of an exhaust air pump in a port-fuel-injected, spark ignition engine was developed. A conventional 4-cylinder engine was operated with three cylinders running rich and the fourth one as an air pump to supply air to the exhaust manifold. Under steady-state cold coolant conditions, this strategy achieved near total oxidation of CO and HC with sufficiently retarded spark timing, resulting in a 400% increase in feedgas enthalpy flow and a 90% reduction in feedgas HC emissions compared to conventional operation. The strategy was also evaluated for crank starts. Using the existing engine hardware, implementing the strategy resulted in a reduction in catalyst light-off time from 28.0 seconds under conventional operation to 9.1 seconds.

SCR on Filter (SCRoF) is an efficient and compact NOX and PM reduction technology already used in series production for light-duty applications. The technology is now finding its way into the medium duty and heavy duty market. One of the key challenges for successful application is the robustness to real world variations. The solution to this challenge can be found by using model-based control algorithms, utilizing state estimation by physics-based catalyst models. This paper focuses on the development, validation and real time implementation of a physics-based control oriented SCRoF model. An overview of the developed model will be presented, together with a brief description of the model parameter identification and validation process using engine test bench measurement data. The model parameters are identified following a streamlined approach, focusing on decoupling the effects of deNOx and soot phenomena.

Regulations on methane emissions from lean-burn natural gas (NG) and lean-burn dual fuel (natural gas and diesel) engines are becoming more stringent due to methane’s strong greenhouse effect. Palladium-based oxidation catalysts are typically used for methane reduction due to their relative high reactivity under lean conditions. However, the catalytic activity of these catalysts is inhibited by the water vapor in exhaust and decreases over time from exposure to trace amounts of sulfur. The reduction of deactivated catalysts in a net rich environment is known to be able to regenerate the catalyst. In this work, a multicycle methane light-off & extinction test protocol was first developed to probe the catalyst reactivity and stability under simulated exhaust conditions. Then, the effect of two different regeneration gas compositions, denoted as regen-A and regen-B, was evaluated on a degreened catalyst and a catalyst previously tested on a natural gas engine.

Natural gas powered vehicles are attractive in certain applications due to their lower emissions in general than conventional diesel engines and the low cost of natural gas. For stoichiometric natural gas engines, the aftertreatment system typically consists only of a three-way catalyst (TWC). However, increasingly stringent NOx and methane regulations challenge current TWC technologies. In this work, a catalyst reactor system with variable lean/rich switching capability was developed for evaluating TWCs for stoichiometric natural gas engines. The effect of varying frequency and duty-cycle during lean/rich gas switching experiments was measured with a hot-wire anemometer (HWA) due to its high sensitivity to gas thermal properties. A theoretical reactor gas dispersion model was then developed and validated with the HWA measurements. The model is capable of predicting the actual lean/rich gas exposure to the TWC under different testing conditions.

Nitrogen dioxide (NO2) is known to pose a risk to human health and contributes to the formation of ground level ozone. In recognition of its human health implications, the American Conference of Governmental Industrial Hygienists (ACGIH) set a Threshold Limit Value (TLV) of 0.2 ppmv NO2 in 2012. For mobile sources, NO2 is regulated as a component of NOx (NO + NO2). In addition, the European Commission has indicated it is considering separate Euro 6 light-duty diesel and Euro VI heavy-duty diesel NO2 emissions limits likely to mitigate the formation of ground level ozone in urban areas. In this study, we conduct component-level reactor-based experiments to understand the effects that various aftertreatment catalyst technologies including diesel oxidation catalyst (DOC), diesel particulate filter (DPF), selective catalytic reduction (SCR) catalyst and ammonia oxidation (AMOX) catalyst have on the formation and mitigation of NO2 emissions.

Titania supported vanadia catalysts have been widely used for the selective catalytic reduction (SCR) of nitrogen oxides (NOx) in diesel exhaust aftertreatment systems. Vanadia SCR (V-SCR) catalysts are preferred for many applications because they have demonstrated advantages of catalytic activity for NOx removal and tolerance to sulfur poisoning. The primary shortcoming of V-SCR catalysts is their thermal durability. Degradation in NOx conversion is also related to aging conditions such as at high temperatures. In this study, the impact that short duration hydrothermal aging has on a state-of-the-art V-SCR catalyst was investigated by aging for 2 hr intervals with progressively increased temperatures from 525 to 700°C. The catalytic performance of this V-SCR catalyst upon aging was evaluated by three different reactions of NH₃ SCR, NH₃ oxidation, and NO oxidation under simulated diesel exhaust conditions from 170 to 500°C.

Achieving high NOx conversion at low-temperature (T ≤ 200 °C) is a topic of active research due to potential reductions in regulated NOx emissions from diesel engines. At these temperatures, ammonium nitrate may form as a result of interactions between NH3 and NO2. Ammonium nitrate formation can reduce the availability of NH3 for NOx conversion and block active catalyst sites. The thermal decomposition of ammonium nitrate may result in the formation of N2O, a regulated Greenhouse Gas (GHG). In this study, we investigate the formation and thermal and chemical decomposition of ammonium nitrate on a state-of-the-art dual-layer ammonia oxidation (AMOX) catalyst. Reactor-based constant-temperature ammonium nitrate formation, temperature programmed desorption (TPD), and NO titration experiments are used to characterize formation and decomposition.