Search Results

Increasingly stringent regulations call for the reduction of emissions at engine startup to purify exhaust gas and reduce the amount of CO2 emitted. Air-fuel ratio (A/F) sensors detect the composition of exhaust gas and provide feedback to control the fuel injection quantity in order to ensure the optimal functioning of the catalytic converter. Reducing the time needed to obtain feedback control and enabling the restriction-free installation of A/F sensors can help meet regulations. Conventional sensors do not activate feedback control immediately after engine startup as the combination of high temperatures and splashes of condensed water in the exhaust pipe can cause thermal shock to the sensor element. Moreover, sensors need to be installed near the engine to increase the catalyst reaction efficiency. This increases the possibility of water splash from the condensed water in the catalyst.

At present, various efforts are being made in the industrial world to preserve the earth's environment. Automobile industry has to comply with the emission control regulations including NOx and PM and the requirement of reducing CO2 emission from the viewpoint of global warming protection and energy saving. In these situations, diesel engines having a high potential to reduce CO2 emission are attracting much attention. In order to enhance the potential of diesel to reduce CO2 while solving its problems (“slow, dirty, noisy”), common rail systems are vital. DENSO developed an advanced common rail system (CRS) that integrates fuel injectors capable of delivering up to five injection events per combustion cycle at 180MPa injection pressure. This paper describes the injection performance and effects of the 180MPa common rail system and then explains the next generation common rail system.

Increased interest in global warming issues requires rapid improvements in reduction of CO2 emissions. The automotive industry is placing high importance on improving fuel economy performance across their entire product lines. Charging Management System is a necessary element towards fuel economy improvement. Many of today's charging management systems perform at least two important functions: improving efficiency based on vehicle motion, and detecting battery state of charge. These systems become more complicated as more components (i.e. generators, current sensors and ECU) and software are added. Therefore, it is difficult to develop charging management systems for an entire product line and difficult to retrofit the system for vehicles already in production. A stand-alone charging management system solves these issues. This system is independent of the other vehicle systems. The software for improving fuel economy is installed in the generator or current sensor.

We have achieved significant weight reduction for the MS (Multi-Tank Super Slim Structure) Evaporator (1)currently in production at DENSO CORPORATION. The evaporator of HVAC unit, located in the instrument panel, is a component of the aluminum heat exchanger used in automotive air conditioners. The new evaporator uses thinner quad-layer sheet material, thanks to optimization of the electrical potential among its outer filler metal, intermediate anodic layer and core. The evaporator is thus lighter than conventional evaporators, but retains equivalent corrosion resistance.

Through the years, aluminum automotive heat exchangers have been developed in order to have a high performance and a light weight. Therefore, the thickness of the aluminum sheets for the application has been reduced. As the brazeability declines with the reduction in thickness, fins having a thickness under 80μm may be difficult to secure a good brazeability. Therefore, we studied the brazeability to determine the limit of thickness using clad fins from 40 to 80μm. The fillet volume formed at the joints of the fin and tube decreased with the decreasing fin thickness and the Si content in both the filler metals and the core alloys. The suitable range of Si content in the filler metals and the core alloys to obtain a good brazeability decreased with the decreasing fin thickness. When the fins were thinner than the critical values, it was impossible to have a good brazeability.

In conventional automobile designs, a radiator for cooling the engine and a condenser for condensing the air-conditioner refrigerant are typically configured independently of each other; they are usually mounted in series in the front of the engine compartment so that they will receive sufficient air flow while the vehicle is running. We have developed a smaller and higher performance cooling module by integrating these two heat exchangers into one unit. (Fig 1) For the heat dissipation fin, we have employed an integral fin construction equipped with an insulating slit, resulting in effective prevention of thermal conduction from the higher temperature radiator side, to the condenser side. We also succeeded in improving heat dissipation performance by making effective use of the connection part of the integral fin.

Having a light weight, a good heat conductivity and a good brazability, aluminum alloy is widely used for automotive heat exchanger systems. The major problem with Aluminum is perforation of the tube by pitting corrosion and corrosion protection is necessary in the field. In radiator and condenser systems using the the Nocolok brazing process given good corrosion resistance using cathodic protection with sacrificial anode made of Zn-sprayed onto tube or low corrosion potential fins etc. On the other hand, in drawn-cup type evaporators, that are fabricated from brazing sheet tubes in vacuum brazing method and then covered low electro-conductive drain water film in operation, the effect of cathodic protection by the anode fin is limited to a very small area. Therefore, this has been studied to improve self-corrosion resistance of the core in the brazing sheet tube.

In automotive air conditioning, balancing comfort and fuel efficiency is very important. Vehicle cooling performance improvements during initial cool down has reached a limit in recent years, especially in very hot regions. We have addressed this issue by developing a unique double-pipe internal heat exchanger. In the main discourse, we first clarify the concept of the internal heat exchanger system (IHE) using the temperature difference between the high and low pressure pipes in the refrigeration cycle, and propose the application of an efficient internal heat exchanger. This unique double-pipe internal heat exchanger can easily be manufactured by inserting the inner pipe into the outer pipe and by fixing the pipes at both ends. The length of the IHE is 400mm. This double-pipe internal heat exchanger can increase cooling performance by 5-12% at the equivalent power consumption levels in the same space as a conventional front air conditioner system.

DENSO started a pilot demonstration of on-site methanation as “CO2 circulation plant” as proactive initiative for CO2 capture and storage/utilization (CCUS) technologies toward achievement of carbon neutrality by 2035 in our own business. The CO2 circulation plant was designed to capture CO2 primarily generated by the plant and recycle it as an energy source of the facility. We also started work on the development of electric swing CO2 adsorption (ESA) technology to achieve low-energy CO2 capture.

A hybrid powertrain offers the potential of a significant fuel saving for heavy-duty Diesel vehicles, which results in CO2 reduction of more than 20%, depending on the application. Using advanced future fuels, like HVO offers additional CO2 saving potential. In addition, the future Diesel engine needs to comply with the next generation of emission legislation, given by the European EUVII and the US EPA2027 regulatory frameworks. To achieve these limits, a combination of different technologies for the engine and the aftertreatment system are required. The proposed paper will present these technology solutions and their impact on CO2 and emissions by means of engine testing and simulation.

Reducing vehicle CO2 emissions is an important measure to help address global warming. To reduce CO2 emissions on a global basis, Toyota Motor Corporation is taking a multi-pathway approach that involves the introduction of the optimal powertrains according to the circumstances of each region, including hybrid electric (HEVs) and plug-in hybrid electric vehicles (PHEVs), as well as battery electric vehicles (BEVs). This report describes the development of a new PHEV system for the Toyota Prius. This system features a traction battery pack structure, transaxle, and power control unit (PCU) with boost converter, which were newly developed based on the 2.0-liter HEV system. As a result, the battery capacity was increased by 1.5 times compared to the previous model with almost the same battery pack size. Transmission efficiency was also improved, extending the distance that the Prius can be driven as an EV by 70%.