Search Results

Knowledge mapping is a first and mandatory step in creation of system architecture. This paper considers the conceptual modeling of automotive systems, and discusses the creation of a knowledge-based model with respect to the Object Process Methodology an approach used in designing intelligent systems by depicting them using object models and process models. With this knowledge, systems engineer should consider what a product is comprised of (its structure), how it operates (its dynamics), and how it interacts with the environment. As systems have become more complex, a prevalent problem in systems development has been the number of accruing errors. A clearly defined and consistent mapping of knowledge regarding structure, operation and interaction is necessary to construct an effective and useful system. An interactive, iterative and consistent method is needed to cope with this complex and circular problem.

The active safety of tractor / trailer-combinations plays an important role in regard to traffic safety in general. For improving the active safety of tractor / trailer-combinations, it is necessary to investigate the interactions between the towing vehicle and the trailer during braking maneuvers. This paper describes the ECE-regulations for the braking force distributions of tractor/full trailer- and tractor / semitrailer-combinations. The influence of different layouts of the braking systems within these regulations on the coupling forces between tractor and trailer and the driving performance of the units during braking is investigated. The dynamical behaviour of a tractor/full-trailer-combination and a tractor / semitrailer-combination are both discussed with the aid of simulations of the ISO-standard testing procedures “Braking in a turn” and “Braking straight ahead”.

During the design, evaluation and optimization process of automotive brake systems brake torque measurements are often crucial. Known brake torque sensors lead to differences in terms of mass, inertia, stiffness and brake cooling compared to a vehicle without measurement equipment. In this contribution a new brake torque sensor is described which proved to be superior to known systems. Either the hub itself is turned into the sensing element or is replaced by a sensing element. Thus mass, inertia, stiffness and cooling conditions are nearly unchanged. A modification of this sensor allows measurement of residual brake torques in a low range (20....50 Nm) with high sensivity and features at the same time a high range (up to 2.000 Nm) with lower sensivity. The application of the sensor in a study to lower energy loss caused by residual brake friction in a passenger car is described.

This paper assesses the potential improvement of automotive powertrain technologies 25 years into the future. The powertrain types assessed include naturally-aspirated gasoline engines, turbocharged gasoline engines, diesel engines, gasoline-electric hybrids, and various advanced transmissions. Advancements in aerodynamics, vehicle weight reduction and tire rolling friction are also taken into account. The objective of the comparison is the potential of anticipated improvements in these powertrain technologies for reducing petroleum consumption and greenhouse gas emissions at the same level of performance as current vehicles in the U.S.A. The fuel consumption and performance of future vehicles was estimated using a combination of scaling laws and detailed vehicle simulations. The results indicate that there is significant potential for reduction of fuel consumption for all the powertrains examined.

The existing vehicle designs exhibit a high level of coupling. For instance the coupling in the suspension and steering systems manifests itself through the change in wheel alignment parameters (WAP) due to suspension travel. This change in the WAP causes directional instability and tire-wear. The approach of the industry to solve this problem has been twofold. The first approach has been optimization of suspension link lengths to reduce the change in WAP to zero. Since this is not possible with the existing architecture, the solution used is the optimization of the spring stiffness K to get a compromise solution for comfort (which requires significant suspension travel and hence a soft spring) and directional stability (which demands least possible change in wheel alignment parameters and hence a stiff spring).

This paper presents the results of a study of how people interacted with a production voice-command based interface while driving on public roadways. Tasks included phone contact calling, full address destination entry, and point-of-interest (POI) selection. Baseline driving and driving while engaging in multiple-levels of an auditory-vocal cognitive reference task and manual radio tuning were used as comparison points. Measures included self-reported workload, task performance, physiological arousal, glance behavior, and vehicle control for an analysis sample of 48 participants (gender balanced across ages 21-68). Task analysis and glance measures confirm earlier findings that voice-command interfaces do not always allow the driver to keep their hands on the wheel and eyes on the road, as some assume.

The quest for higher efficiency and performance of automotive vehicles requires application of materials with high strength, stiffness and lower weight in their construction. Particulate-reinforced aluminum-matrix composites are cost-competitive materials, which can meet these requirements. MMCC, Inc. has been optimizing particulate-reinforced alloy systems and developing the Advanced Pressure Infiltration Casting (APIC™) process for the manufacture of components from these materials. This paper discusses the results of a recent study in which composites reinforced with 55 vol.% alumina were cast using two sizes of alumina particulate and eight different matrix alloys based on Al-4.5 wt.% Cu with varying amounts of silicon and magnesium. Optimum heat treatments for each alloy were determined utilizing microhardness studies. The tensile strength and fracture toughness were evaluated as a function of alloy chemistry, particulate size, and heat treatment.

By-wire systems have been established for several years in the area of aircraft constructions. There is the visible trend to realize by-wire applications without mechanical or hydraulic backup systems in vehicles. The required electronic systems must evidently be available and safe. This paper addresses a new automotive architecture approach using the time-triggered fault-tolerant TTP protocol that has been designed for class C safety related control applications, like brake-by-wire or steer-by-wire, due to the SAE classification [1]. As an example we present this approach within a brake-by-wire research car (case study) without mechanical backup. The intention of this architecture is to tolerate one arbitrary fault - excepting faults of actuators - without any effects of the brake performance. For this purpose we use redundancy in communication (TTP) and electric components like sensors, actuators and power supply.

In this paper we investigate the optimal forming of conical cups of AL 2008-T4 through the use of real-time process control. We consider a flat, frictional binder the force of which can be determined precisely through closed-loop control. Initially the force is held constant throughout the forming of the cup, and various levels of force are tested experimentally and with numerical simulation. Excellent agreement between experiment and simulation is observed. The effects of binder force on cup shape, thickness distribution, failure mode and cup failure height are investigated, and an “optimal” constant binder force is determined. For this optimal case, the corresponding punch force is recorded as a function of punch displacement and is used in subsequent closed-loop control experiments. In addition to the constant force test, a trial variable binder force test was performed to extend the failure height beyond that obtained using the “optimal” constant force level.

In the following essay, vehicle, and test stand related measuring and calculating methods will be introduced which have proven to be a suitable basis for the discussion of the criteria of driving mechanics for commercial vehicles (1 to 23). Because of the progress of electronics development these methods are reliable and quickly performed today. In connection with tire and brake characteristics, which are the basis for measuring driving maneuvers, and with the knowledge of axle and wheel movement, a purposeful and physically correct evaluation of the driving behavior of vehicles is possible. With the aid of complex mathematical vehicle substitution systems it is already possible to accurately estimate tendencies in the pre-development stage of a vehicle.

Information on the driving stability can be obtained in the form of oversteer or understeer tendencies and acceleration limits on a circular path. Up to now the calculations have only been made on an ideal, even roadway. Significant dynamic characteristics, such as the tuning of the shock absorbers, which also play a role in evaluating the stability of a vehicle in a driving test, are thereby not included in the calculations. In this paper the unevenness of the roadway is taken into consideration in calculating steady state cornering tests. Different vehicle models can be evaluated in regard to their handling or active safety with the aid of the driver's steering actions required to keep the car on course.

Daimler-Benz have developed an automatically/electronically controlled traction system, the 4MATIC. Great store has been set by active safety. This paper deals with the problems involved in 4-Wheel drive and analyzes the reasons which led to the 4MATIC concept. Depending on the conditions encountered, the drive components engage automatically one after the other in the sequence front-wheel drive - interaxle differential lock - rear axle differential lock. The engagement, and thus the approaching limits of driving dynamics, is indicated to the driver by an indicator lamp so that he can adjust to the deteriorated conditions in time. A further important advantage of this system is the automatic disengagement of the differential locks when braking so that the anti-lock braking remains fully effective.