Search Results

In a harmonized ESA/NIVR project the performance of membrane gas absorption for the simultaneous removal of carbon dioxide and moisture has been determined experimentally at carbon dioxide and humidity concentration levels representative for spacecraft conditions. Performance data at several experimental conditions have been collected. Removal of moisture can be controlled by the temperature of the absorption liquid. Removal of carbon dioxide is slightly affected by the temperature of the absorption liquid. Based on these measurements a conceptual design for a carbon dioxide and humidity control system for the Crew Transport Vehicle (CTV) is made. For the regeneration step in this design a number of assumptions have been made. The multifunctionality of membrane gas absorption makes it possible to combine a number of functions in one compact system.

Because of the reduction on the remaining Shuttle launches, the initial mission that was assigned for MELFI, the Minus Eighty degrees Celsius Laboratory Freezer for ISS, has been significantly modified. While the design was made for a MELFI flying 15 times over a period of 10 years with individual missions no longer than 2 years, present scenario requires to have MELFI in orbit up to 7 years. Extending the MELFI on orbit life from two to seven years has required staggered assessments, each of them aiming at preserving as much as possible the existing design. The potential life limited items are evaluated. On orbit maintenance will be extended for a longer period and maintenance activities foreseen initially to be done on ground between flights will be adapted for orbit. Degraded modes are evaluated so that MELFI ensures its mission at the end of the life even with some off-nominal conditions.

Methane-filled heat pipes have been developed and qualified for the SCIAMACHY thermal bus assembly. The heat pipes provide an efficient heat transfer in the temperature range 100-160 K. Extensive qualification testing has been performed. The thermal bus assembly is part of the Thermal Bus Unit (TBU) of the SCIAMACHY Radiant Cooler.

A Heat Switch has been developed, namely a device able to autonomously regulate its own thermal conductance in function of the equipment dissipation and environmental heat sink conditions. It is based on a Loop Heat Pipe (LHP) technology, with a passive bypass valve which diverts the flow to the Compensation Chamber when needed for regulation purposes. The target application is the potential use on a Mars Rover thermal control system. The paper recalls the Heat Switch design, and reports the results of an extensive test campaign on the ground demonstrator. The performance of the device was found extremely satisfying, and often exceeded the system requirements.

Jules Verne – the first ATV model developed by ASTRIUM on behalf of ESA – has been controlled by CNES Toulouse Control Centre from March to September 2008. The Engineering Support Team (EST) was in charge to provide System expertise and to propose relevant recommendations in case of off nominal situations. This paper deals with the operations carried out by the EST Thermal position during the JV flight, such as: Identification of thermal anomalies triggered by onboard software or by ground monitoring; Analysis of actual situation from available flight data; Correction implemented thanks to a complete set of commands and procedures; Check on the on-board configuration after correction uploading.

During Extravehicular Activities (EVA) an astronaut has to be protected against various external factors ranging from mechanical hazards to solar radiation and micrometeoroids. An important element in this external protection is the outermost fabric layer. It has to ensure the mechanical protection of the pressure retention bladder and at the same time - by its thermooptical properties - plays an important role in the thermal control of the space suit. New weaving and knitting technologies enable the fabrication of so-called 3-D fabrics with interconnected layers and local variation of properties in one manufacturing step. By this a tailored design of protection properties is possible. A study has been performed to define concepts adapted for use on a European Space Suit. Different fabric samples were manufactured and tested, amongst others, for strength, flexibility, puncture and wear resistance, UV stability, flammability, out/offgassing and micrometeoroid protection effctiveness.

The ESA Polar Platform, as part of the ESA Columbus Development Programme, is scheduled to be launched as single passenger by an Ariane 5 vehicle in mid 1998. The multimission platform is designed to accommodate a wide range of payload complements to be flown on a series of missions in order to satisfy the growing future earth observation needs in continuation of the current ERS programme. Multi-mission capability is achieved by design modularity wherever feasible and cost-effective. This paper describes the thermal control design of the Polar Platform which follows its modular configuration and which has to cope with a wide range of generic performance parameters, whilst being adaptable to provide optimised performance for specific missions. Special thermal control features are highlighted as the software and hardware controlled heater systems, thermal doublers using carbon / carbon material and the battery compartment heat pipe radiator.

Verification of the Integrated Overall Thermal Mathematical Model (IOTMM) is one of the last tasks in the thermal and environmental control area of the Columbus module. For this purpose a specific test covering as well thermal-hydraulic performance tests as Environmental Control and Life Support (ECLS) cabin temperature control functions has been defined and performed on the european Columbus Protoflight Model (PFM) in Bremen in 2003. This Environmental Control System test was successful for all Active Thermal Control System (ATCS) related thermal-hydraulic functions and could provide sufficient data for a proper IOTMM correlation. However, it failed to verify the ECLS related functions as cabin temperature control and ventilation. Data, which have been generated during this first test, could not be used for a successful IOTMM correlation related to ECLS subsystem performance and modelling.

The Minus Eighty (Degrees Celsius) Laboratory Freezer for the International Space Station (MELFI) is one of the freezers developed by ESA on behalf of NASA. Peculiar requirements for that facility are the long-term storage at low temperature, the rapid freezing of specimen to the required temperature, the large cold volume (300 l) and the low power consumption. To verify those requirements before the manufacturing of the flight hardware, a dedicated test campaign was performed on a ground model. This paper will start with a system overview, showing the main features of MELFI. The test set-up as well as their results will be presented and discussed, with particular emphasis on the methods used to predict the on-orbit (0-gravity) behaviour, by avoiding the sample internal convection and dewar internal convection during the test execution.

As part of the European contribution to the Russian segment of the International Space Station (ISS), the European Robotic Arm (ERA) is designed under contract of the European Space Agency by Fokker Space as the Prime contractor. The particularly challenging aspect of the ERA thermal design is to enable ERA operation under all possible in-orbit thermal environmental conditions which are to be experienced throughout its 10 year life. These conditions can be between extreme cold without sunlight for hibernation to extreme hot with ERA operating in full sunlight in close vicinity to a large station item, for instance, the solar arrays. First a short description of the ERA system is given with a summary of the main thermal design features. The system level thermal balance test on the ERA Engineering Qualification Model (EQM) is intended to validate the system level thermal model, which consists of the subsystem thermal models as supplied by the respective subcontractors.