Refine Your Search

Topic

Author

Search Results

Technical Paper

Performance and Durability Evaluation of Continuously Regenerating Particulate Filters on Diesel Powered Urban Buses at NY City Transit

2001-03-05
2001-01-0511
Particulate emission from diesel engines is one of the most important pollutants in urban areas. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled “Clean Diesel Demonstration Program” has been initiated by NY City Transit under the supervision of NY State DEC and with active participation from several industrial partners. Under this program, several NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter system and are operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses are being evaluated over a 8-9 month period for operations, maintainability and durability of the particulate filter.
Technical Paper

Time-Resolved, Speciated Emissions from an SI Engine During Starting and Warm-Up

1996-10-01
961955
A sampling system was developed to measure the evolution of the speciated hydrocarbon emissions from a single-cylinder SI engine in a simulated starting and warm-up procedure. A sequence of exhaust samples was drawn and stored for gas chromatograph analysis. The individual sampling aperture was set at 0.13 s which corresponds to ∼ 1 cycle at 900 rpm. The positions of the apertures (in time) were controlled by a computer and were spaced appropriately to capture the warm-up process. The time resolution was of the order of 1 to 2 cycles (at 900 rpm). Results for four different fuels are reported: n-pentane/iso-octane mixture at volume ratio of 20/80 to study the effect of a light fuel component in the mixture; n-decane/iso-octane mixture at 10/90 to study the effect of a heavy fuel component in the mixture; m-xylene and iso-octane at 25/75 to study the effect of an aromatics in the mixture; and a calibration gasoline.
Technical Paper

Numerical Simulation of Post-Flame Oxidation of Hydrocarbons in Spark Ignition Engines

1997-02-24
970886
About 50-90 percent of the hydrocarbons that escape combustion during flame passage in spark-ignition engine operation are oxidized in the cylinder before leaving the system. The process involves the transport of unreacted fuel from cold walls towards the hotter burned gas regions and subsequent reaction. In order to understand controlling factors in the process, a transient one-dimensional reactive-diffusive model has been formulated for simulating the oxidation processes taking place in the reactive layer between hot burned gases and cold unreacted air/fuel mixture, with initial and boundary conditions provided by the emergence of hydrocarbons from the piston top land crevice. Energy and species conservation equations are solved for the entire process, using a detailed chemical kinetic mechanism for propane.
Technical Paper

Investigation of the Dilution Process for Measurement of Particulate Matter from Spark-Ignition Engines

1998-10-19
982601
Measurements of particulate matter (PM) from spark ignition (SI) engine exhaust using dilution tunnels will become more prevalent as emission standards are tightened. Hence, a study of the dilution process was undertaken in order to understand how various dilution related parameters affect the accuracy with which PM sizes and concentrations can be determined. A SI and a compression ignition (CI) engine were separately used to examine parameters of the dilution process; the present work discusses the results in the context of SI exhaust dilution. A Scanning Mobility Particle Sizer (SMPS) was used to measure the size distribution, number density, and volume fraction of PM. Temperature measurements in the exhaust pipe and dilution tunnel reveal the degree of mixing between exhaust and dilution air, the effect of flowrate on heat transfer from undiluted and diluted exhaust to the environment, and the minimum permissible dilution ratio for a maximum sample temperature of 52°C.
Technical Paper

Liquid Fuel Visualization Using Laser-Induced Fluoresence During Cold Start

1998-10-19
982466
The presence of liquid fuel inside the engine cylinder is believed to be a strong contributor to the high levels of hydrocarbon emissions from spark ignition (SI) engines during the warm-up period. Quantifying and determining the fate of the liquid fuel that enters the cylinder is the first step in understanding the process of emissions formation. This work uses planar laser induced fluorescence (PLIF) to visualize the liquid fuel present in the cylinder. The fluorescing compounds in indolene, and mixtures of iso-octane with dopants of different boiling points (acetone and 3-pentanone) were used to trace the behavior of different volatility components. Images were taken of three different planes through the engine intersecting the intake valve region. A closed valve fuel injection strategy was used, as this is the strategy most commonly used in practice. Background subtraction and masking were both performed to reduce the effect of any spurious fluorescence.
Technical Paper

Evaluations of Current Natural Gas Vehicle Technology Exhaust Emissions at Various Operating Temperatures

1995-10-01
952437
As more stringent vehicle emission standards are introduced worldwide, there is an increased need to provide a thorough assessment of the environmental impact of alternative fuels. With the advent of CNG as a viable transportation fuel, the development of advanced computer controlled fuel delivery systems is imperative in order to ensure acceptable emission performance. At present, the majority of light and medium duty engines operating on natural gas are primarily gasoline automotive engines which have been retrofitted to allow for the use of CNG. The Mobile Sources Emissions Division of Environment Canada and the Canadian Gas Association have conducted a joint test program in order to develop a database of exhaust emissions from vehicles typically converted for operation on either gasoline or natural gas at various operating temperatures.
Technical Paper

Analysis of Fuel Behavior in the Spark-Ignition Engine Start-Up Process

1995-02-01
950678
An analysis method for characterizing fuel behavior during spark-ignition engine starting has been developed and applied to several sets of start-up data. The data sets were acquired from modern production vehicles during room temperature engine start-up. Two different engines, two control schemes, and two engine temperatures (cold and hot) were investigated. A cycle-by-cycle mass balance for the fuel was used to compare the amount of fuel injected with the amount burned or exhausted as unburned hydrocarbons. The difference was measured as “fuel unaccounted for”. The calculation for the amount of fuel burned used an energy release analysis of the cylinder pressure data. The results include an overview of starting behavior and a fuel accounting for each data set Overall, starting occurred quickly with combustion quality, manifold pressure, and engine speed beginning to stabilize by the seventh cycle, on average.
Technical Paper

Effects of Lubrication System Parameters on Diesel Particulate Emission Characteristics

1996-02-01
960318
The effects of lubrication system parameters on particulate emission rate and composition were studied. Engine load, viscosity and piston-ring gap were varied. Particulate rate and composition were measured for multiple combinations of lubricant and ring-gap configurations at three different engine operating conditions. Particulate rates were higher with the lower viscosity oil and larger with the wider top-ring gap. At high load, the difference in particulate rate was due to changes in the non-soluble portion, while at medium and low loads, the change in particulate rate was due to differences in the lubricant-derived portion of the soluble organic fraction (SOF). Additionally, changes in the fuel-derived portion of the SOF were discovered and attributed to changes in fuel-absorption in the oil film.
Technical Paper

Extent of Oxidation of Hydrocarbons Desorbing from the Lubricant Oil Layer in Spark-ignition Engines

1996-02-01
960069
The extent of oxidation of hydrocarbons desorbing from the oil layer has been measured directly in a hydrogen-fueled, spark-ignited engine in which the lubricant oil was doped with a single component hydrocarbon. The amount of hydrocarbon desorbed and oxidized could be measured simultaneously as the dopant was only source of carbon-containing species. The fraction oxidized was strongly dependent on engine load, hydrogen fuel-air ratio and dopant chemical reactivity, but only modestly dependent on spark timing and nitrogen dilution levels below 20 percent. Fast FID measurements at the cylinder exit showed that the surviving hydrocarbons emerge late in the exhaust stroke.
Technical Paper

Development of a Time and Space Resolved Sampling Probe Diagnostic for Engine Exhaust Hydrocarbons

1996-02-01
961002
In order to understand how unburned hydrocarbons emerge from SI engines and, in particular, how non-fuel hydrocarbons are formed and oxidized, a new gas sampling technique has been developed. A sampling unit, based on a combination of techniques used in the Fast Flame Ionization Detector (FFID) and wall-mounted sampling valves, was designed and built to capture a sample of exhaust gas during a specific period of the exhaust process and from a specific location within the exhaust port. The sampling unit consists of a transfer tube with one end in the exhaust port and the other connected to a three-way valve that leads, on one side, to a FFID and, on the other, to a vacuum chamber with a high-speed solenoid valve. Exhaust gas, drawn by the pressure drop into the vacuum chamber, impinges on the face of the solenoid valve and flows radially outward.
Technical Paper

Measurement of Gasoline Absorption into Engine Lubricating Oil

1996-05-01
961229
A method to collect and speciate the components of gasoline absorbed in the lubricant oil using gas chromatography has been developed. Samples were collected continuously from the piston skirt, baffle and sump in a Saturn engine. A long (18 hours) test was performed to determine the build up of hydrocarbons in the sump, and a shorter (25 min) test was performed to determine the build up of hydrocarbons in the piston skirt and baffle during engine warm-up. The first experiment showed that the total hydrocarbon concentration in the sump oil reached a steady state of about 1.35% mass fraction after 11 hours of engine operation. The relative concentration of individual fuel hydrocarbon species absorbed in the oil increases exponentially with boiling point. Most of the identified species in the oil consist of the heavy end aromatics. Similar compositions but lower concentrations were found for samples collected from the piston skirt during engine warm-up.
Technical Paper

Nitrous Oxide Emissions from Light Duty Vehicles

1994-03-01
940304
Recent evidence has linked vehicle catalysts to nitrous oxide emissions. As the population of catalyst-equipped vehicles increases, so does the need for a better understanding of this powerful greenhouse gas. Nitrous oxide measurements were made on fourteen vehicles over the FTP urban and highway cycles utilizing an FTIR analyzer. To quantify emissions from aged catalysts, emphasis was placed on testing in-use vehicles with oedometer readings between 30,000 and 120,000 kilometres. Tailpipe N2O emissions averaged 126 mg/mile for the nine aged catalyst vehicles and 74 mg/mile for the five new catalyst cars. These results are about two times greater than previous N2O studies using the FTP cycle. Also, twice as much N2O was produced during the urban driving cycle, than during the highway cycle. Based on our measurements, N2O emissions from light duty vehicles in Canada were estimated to range from 8 to 20 kilotonnes for 1992.
Technical Paper

Aggregate Vehicle Emission Estimates for Evaluating Control Strategies

1994-03-01
940303
Currently, states that are out of compliance with the National Ambient Air Quality Standards must, according to the Clean Air Act Amendments of 1990 (CAAA), develop and implement control strategies that demonstrate specific degrees of reduction in emissions-with the degree of reduction depending upon the severity of the problem. One tool that has been developed to aid regulators in both deciding an appropriate course of action and to demonstrate the desired reductions in mobile emissions is EPA's Mobile 5a emission estimation model. In our study, Mobile 5a has been used to examine the effects of regulatory strategies, as applied to the Northeast United States, on vehicle emissions under worst-case ozone-forming conditions.
Technical Paper

The Effects of Crevices on the Engine-Out Hydrocarbon Emissions in SI Engines

1994-03-01
940306
To understand the effects of crevices on the engine-out hydrocarbon emissions, a series of engine experiments was carried out with different piston crevice volumes and with simulated head gasket crevices. The engine-out HC level was found to be modestly sensitive to the piston crevice size in both the warmed-up and the cold engines, but more sensitive to the crevice volume in the head gasket region. A substantial decrease in HC in the cold-to-warm-up engine transition was observed and is attributed mostly to the change in port oxidation.
Technical Paper

A Species-Based Multi-Component Volatility Model for Gasoline

1994-10-01
941877
A fuel volatility model based on the major species present in the fuel has been formulated. The model accurately predicts the ASTM distillation curves and Reid Vapor Pressure for hydrocarbon fuels. The model may be used to assess the fuel effects on the extent of evaporation and the vapor composition in the mixture preparation process.
Technical Paper

Auto-Oil Program Phase II Heavy Hydrocarbon Study: Analysis of Engine-Out Hydrocarbon Emissions Data

1994-10-01
941966
The engine-out (EO) total and speciated hydrocarbon emissions data from the Auto-Oil Program Phase II Heavy Hydrocarbon Study had been analyzed. The methodology was to first investigate the stabilized EO emissions (Bag 2) of a specific vehicle (Vehicle 04B, a 1989 Model Year Ford Taurus); then the vehicle-to-vehicle differences in Bag2 emissions were considered. Finally, the differences in the Bag2 and the starting/warm-up EO emissions (Bag1) were examined. The speciated emissions may be interpreted as a “feed-through” part due to the unreacted fuel species, and an “offset” part due to the decomposition products. The significant non-fuel emitted species were methane and the olefins. The HC emissions for vehicles with different total emissions were similar in species composition. For both the total and speciated emissions, there was no substantial difference between the Bag1 and Bag2 values for Vehicle 04B.
Technical Paper

Novel Experiment on In-Cylinder Desorption of Fuel from the Oil Layer

1994-10-01
941963
A technique has been developed to measure the desorption and subsequent oxidation of fuel in the oil layer by spiking the oil with liquid fuel and firing the engine on gaseous fuel or motoring with air. Experiments suggest that fuel desorption is not diffusion limited above 50 °C and indicated that approximately two to four percent of the cylinder oil layer is fresh oil from the sump. The increase in hydrocarbon emissions is of the order of 100 ppmC1 per 1% liquid fuel introduced into the fresh oil in a methane fired engine at mid-speed and light load conditions. Calculations indicate that fuel desorbing from oil is much more likely to produce hydrocarbon emissions than fuel emerging from crevices.
Technical Paper

Auto-Oil Program Phase II Heavy Hydrocarbon Study: Fuel Species Oxidation Chemistry and Its Relationship to the Auto-Oil Data

1994-10-01
941970
The oxidation chemistry of paraffins, aromatics, olefins and MTBE were examined. Detailed chemical kinetics calculations were carried out for oxidation of these compounds in the engine cycle. The oxidation rates are very sensitive to temperature. At temperatures of over 1400 K (depending on the fuel), all the hydrocarbons are essentially oxidized for typical residence time in the engine. Based on the kinetics calculations, a threshold temperature is defined for the conversion of the fuel species to CO, CO2, H2O and partially oxidized products. The difference in the survival fraction between aromatics and non-aromatics is attributed to the higher threshold temperature of the aromatics.
Technical Paper

Emissions from Methanol, Ethanol, and Diesel Powered Urban Transit Buses

1994-11-01
942261
The recent tightening of emission standards for new heavy duty engines has lead to the development and implementation of alternative fuel engines, particularly for urban transit bus applications. Alternative fuels are intended to offer a potential emissions benefit with regards to the regulated emissions, and especially the particulate matter, which has received the greatest degree of regulatory action. However, the entire composition of the engine emissions should be considered when evaluating the environmental benefits of these new fuels, and also the continued performance of these engines in actual fleet service. In this study the exhaust emissions from methanol, ethanol, and diesel - powered buses were determined during transient operation of the vehicles on a heavy duty chassis dynamometer. The tests of the alcohol fuelled buses, and a control diesel bus were conducted as the buses accumulated mileage in revenue generating service.
Technical Paper

Effect of Engine Operating Parameters on Hydrocarbon Oxidation in the Exhaust Port and Runner of a Spark-Ignited Engine

1995-02-01
950159
The effect of engine operating parameters (speed, spark timing, and fuel-air equivalence ratio [Φ]) on hydrocarbon (HC) oxidation within the cylinder and exhaust system is examined using propane or isooctane fuel. Quench gas (CO2) is introduced at two locations in the exhaust system (exhaust valve or port exit) to stop the oxidation process. Increasing the speed from 1500 to 2500 RPM at MBT spark timing decreases the total, cylinder-exit HC emissions by ∼50% while oxidation in the exhaust system remains at 40% for both fuels. For propane fuel at 1500 rpm, increasing Φ from 0.9 (fuel lean) to 1.1 (fuel rich) reduces oxidation in the exhaust system from 42% to 26%; at 2500 RPM, exhaust system oxidation decreases from 40% to approximately 0% for Φ = 0.9 and 1.1, respectively. Retarded spark increases oxidation in the cylinder and exhaust system for both fuels. Decreases in total HC emissions are accompanied by increased olefinic content and atmospheric reactivity.
X