Search Results

Gaseous and particle emissions from a gasoline direct injection (GDI) and a port fuel injection (PFI) vehicle were measured at various ambient temperatures (22°C, -7°C, -18°C). These vehicles were driven over the U.S. Federal Test Procedure 75 (FTP-75) and US06 Supplemental Federal Test Procedure (US06) on Tier 2 certification gasoline (E0) and 10% by volume ethanol (E10). Emissions were analyzed to determine the impact of ambient temperature on exhaust emissions over different driving conditions. Measurements on the GDI vehicle with a gasoline particulate filter (GPF) installed were also made to evaluate the GPF particle filtration efficiency at cold ambient temperatures. The GDI vehicle was found to have better fuel economy than the PFI vehicle at all test conditions. Reduction in ambient temperature increased the fuel consumption for both vehicles, with a much larger impact on the cold-start FTP-75 drive cycle observed than for the hot-start US06 drive cycle.

This study reports gaseous and particle (ultrafine and black carbon (BC)) emissions from a turbofan engine core on standard Jet A-1 and three alternative fuels, including 100% hydrothermolysis synthetic kerosene with aromatics (CH-SKA), 50% Hydro-processed Esters and Fatty Acid paraffinic kerosene (HEFA-SPK), and 100% Fischer Tropsch (FT-SPK). Gaseous emissions from this engine for various fuels were similar but significant differences in particle emissions were observed. During the idle condition, it was observed that the non-refractory mass fraction in the emitted particles were higher than during higher engine load condition. This observation is consistent for all test fuels. The 100% CH-SKA fuel was found to have noticeable reductions in BC emissions when compared to Jet A-1 by 28-38% by different BC instruments (and 7% in refractory particle number (PN) emissions) at take-off condition.

The exhaust emissions from small engines in general and marine engines in particular have come under scrutiny over the past few years as new exhaust emission regulations have been proposed and put into force. The standard method for exhaust emission sampling of outboard marine engines is to analyze raw exhaust in the exhaust manifold of the engine. In this study a total dilution sampling system for the gaseous emissions, similar to what is used for light and heavy duty vehicles and engines, and a separate water sampling method were used to evaluate the exhaust emissions from stock two and four stroke outboard marine engines.

This paper presents the emission characteristics of a HCCI engine operation using n-heptane. The experiments were conducted in a single cylinder Co-operative Fuel Research (CFR) engine equipped with an air-assist port fuel injector. The effects of intake temperature, air/fuel ratio, compression ratio, turbo-charging, and EGR rate on exhaust emissions were explored. The analysis of the exhaust gases included oxides of nitrogen (NOx), nitrous oxide (N2O), carbon monoxide (CO), total hydrocarbon (THC), and soot. The hydrocarbon species present in exhaust gases and their concentrations at several operating conditions were also characterized. The strategies to obtain low HC, CO and NOx emissions are presented and discussed. The approaches to effectively retard HCCI combustion phase without deteriorating combustion efficiency are examined. It was found that HCCI combustion produces extremely low soot and NOx emissions.

Gasoline-electric hybrid vehicle technology has been gaining widespread acceptance and has the potential to reduce emissions through reduced fuel consumption. In this study, particulate matter number and mass emission rates, organic and elemental carbon compositions, and number-based size distributions were measured from four gasoline-electric hybrid vehicles (2005 Ford Escape Hybrid, 2004 Toyota Prius, 2003 Honda Civic Hybrid, and 2000 Honda Insight). In addition, one small conventional gasoline vehicle (2002 SmartCar) was tested. The vehicles were driven over five driving cycles and at steady-state speeds of 40 and 80 km/h. Each test was performed at 20°C and at -18°C. Testing took place at the Environmental Science & Technology Centre of Environment Canada using conventional chassis dynamometer procedures. Average distance based emission rates are given for each vehicle under each test condition.

Fuel consumption and gaseous emission data (CO, NOx, THC, and CO2) are reported for four commercially available gasoline-electric hybrid vehicles and one conventional gasoline vehicle tested on a chassis dynamometer over five transient driving cycles (LA4, LA92, HWFET, NYCC, US06), and two steady state modes (40 and 80 km/h), at two ambient temperatures (20 °C, and -18 °C). All vehicles exhibited higher fuel consumption during transient cycles compared to steady-state modes. Cold ambient temperature had a more detrimental effect on fuel consumption rates of the hybrid vehicles compared to those of the conventional gasoline vehicle.

This paper reports the results of a fuel economy and regulated emissions survey of 15 gasoline powered generators. Tests were conducted at Environment Canada's Emission Research and Measurement Division (ERMD) facilities in Ottawa. The generators ranged in output capacity from 0.9kW to 7.0kW maximum rated output (MRO). They were obtained from a variety of sources including commercial rental companies and from other Environment Canada Divisions. The generators were operated on summer grade commercial fuel over a 6 mode test cycle when possible. The testing was designed to mimic the certification test the engines would undergo in an engine dynamometer test configuration with the exception that the loading was simulated by a load bank connected to the generators electrical output(s).

Selective catalytic reduction (SCR) technology is being considered as the potential strategy for significant reduction of NOx emissions from diesel engines. Many challenges exist in the development of an On-Road SCR retrofit system in terms of system integration and optimization of control strategy in order to achieve highest NOx reduction given the diversity of duty cycles. The main considered challenges are: - The development of a generic control strategy that would work for a broad range of engines, - Development of a reliable and durable injection system that would be able to withstand the harsh environments on a heavy-duty vehicle, - Packaging of the system to be able to fit on a number of vehicles with different configurations, - Controlling ammonia slip and assurance of reducing agent (Urea) availability and quality. In this study a prototype SCR system was evaluated over engine and chassis dynamometer test cycles.

The dependence of gasoline-electric hybrid vehicle energies on driving conditions and ambient temperature is presented for different drive cycles (2xLA4, 2xLA92, 2xUS06, HWFET and 2xNYCC) and temperatures (20°C and -18°C). The tests were carried out at the Emissions Research and Measurement Division of Environment Canada. Hybrid battery pack current was measured at a frequency of 10 Hz. Regenerative braking energy, charging energy from the engine and battery discharge energy were estimated by using modal speed. The magnitudes of battery energies were found to be directly related to drive cycle properties. Battery discharge energy was very strongly correlated to emission factors of CO₂, while energy recovered by regenerative braking and charging energy from the engine had low to very strong correlations to CO₂ emission factors. CO, NOx and HC had low linear correlations to battery discharge energy.

For this work, a methodology of modeling and predicting fuel consumption in a hybrid vehicle as a function of the engine operating temperature has been developed for cold ambient operation (-7°C, 266°K). This methodology requires two steps: 1) development of a temperature dependent engine brake specific fuel consumption (BSFC) map, and, 2) a data-fitting technique for predicting engine temperature to be used as an input to the temperature dependent BSFC maps. For the first step, response surface methodology (RSM) techniques were applied to generate brake specific fuel consumption (BSFC) maps as a function of the engine thermal state. For the second step, data fitting techniques were also used to fit a simplified lumped capacitance heat transfer model using several experimental datasets. Utilizing these techniques, an analysis of fuel consumption as a function of thermal state across a broad range of engine operating conditions is presented.

Particulate emission from diesel engines is one of the most important pollutants in urban areas. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled “Clean Diesel Demonstration Program” has been initiated by NY City Transit under the supervision of NY State DEC and with active participation from several industrial partners. Under this program, several NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter system and are operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses are being evaluated over a 8-9 month period for operations, maintainability and durability of the particulate filter.

This paper will present emissions durability data from an underground mining vehicle equipped with diesel particulate filter technology, which was followed over 4000 hrs on a Detroit Diesel Series 60 engine. The twin particulate filter system is catalyzed using a base metal formulation on cordierite wall flow monoliths. After the durability accumulation, the recovered filters were individually emissions tested on a Detroit Diesel Series 50 engine over the ISO 8178 test cycle. Performance, maintenance and emissions issues pertaining to base metal catalysts will be discussed.

In urban areas, particulate emission from diesel engines is one of the pollutants of most concern. As a result, particulate emission control from urban bus diesel engines using particle filter technology is being evaluated at several locations in the US. A project entitled, “Clean Diesel Vehicle Air Quality Project” has been initiated by NY City Transit under the supervision of NYSDEC and with active participation from several industry partners. Under this program, 25 NY City transit buses with DDC Series 50 engines have been equipped with continuously regenerating diesel particulate filter systems and have been operating with ultra low sulfur diesel (< 30 ppm S) in transit service in Manhattan since February 2000. These buses were evaluated over a 9 month period for operations, maintainability and durability of the particulate filter.

The objective of this work is to better understand freezing fog/drizzle conditions using observations collected during the Fog Remote Sensing and Modeling project (FRAM-S) that took place at St. John's International Airport, St. John's, NL, Canada. This location was ~1 km away from the Atlantic Ocean coast. During the project, the following measurements at one minute resolution were collected: precipitation rate (PR) and amount, fog/drizzle microphysics, 3D wind speed (Uh) and turbulence (Uh'), visibility (Vis), IR and SW radiative fluxes, temperature (T) and relative humidity (RH), and aerosol observations. The reflectivity and microphysical parameters obtained from the Metek Inc. MRR (Microwave Rain Radar) were also used in the analysis. The measurements were then used to obtain freezing fog/drizzle microphysical characteristics and their relation to visibility.

A 1.9L turbocharged direct-injection engine representing a model year 1998-2003 Volkswagen vehicle, equipped with the OEM diesel oxidation catalyst (DOC) and exhaust gas recirculation (EGR), was tested on an eddy-current engine dynamometer with a critical flow venturi-constant volume sampling system (CFV-CVS). The engine was operated over three steady-state modes: 1600 rev/min at 54 Nm; 1800 rev/min at 81 Nm; and 2000 rev/min at 98 Nm. Commercially available ultra-low sulfur diesel fuel (≺15 ppm S) was splash-blended with fatty acid methyl ester biodiesels derived from three different feedstocks: canola, soy, and tallow/waste fry oil. Test blend levels included: 0%, 2%, 5%, 20%, 50%, and 100% biodiesel for each feedstock.

Adoption of hydro-processed esters and fatty acid biojet fuels is a critical component for the sustainability of the aviation industry. Aviation biofuels reduce pollution and provide alternatives to conventional fossil fuels. A study of the impacts of biofuels on emissions from a T56 turbo-prop engine was undertaken as a joint effort among several departments of the Government of Canada. In this study, particulate (including particle number and black carbon (BC) mass) and regulated gaseous emissions (CO2, CO, NO, NO2, THC) were characterized with the engine operating on conventional F-34 jet fuel and jet fuel blended with camelina-based hydro-processed biojet fuel (C-HEFA) by 50% in volume. Emissions characterization, conducted after 20-hour ground engine durability tests, showed immediate significant reductions in particle number and BC mass when the engine was operated on the C-HEFA blend.

The quest for higher efficiency and performance of automotive vehicles requires application of materials with high strength, stiffness and lower weight in their construction. Particulate-reinforced aluminum-matrix composites are cost-competitive materials, which can meet these requirements. MMCC, Inc. has been optimizing particulate-reinforced alloy systems and developing the Advanced Pressure Infiltration Casting (APIC™) process for the manufacture of components from these materials. This paper discusses the results of a recent study in which composites reinforced with 55 vol.% alumina were cast using two sizes of alumina particulate and eight different matrix alloys based on Al-4.5 wt.% Cu with varying amounts of silicon and magnesium. Optimum heat treatments for each alloy were determined utilizing microhardness studies. The tensile strength and fracture toughness were evaluated as a function of alloy chemistry, particulate size, and heat treatment.

The New York City Metropolitan Transit Authority (MTA) has initiated a program to utilize various diesel emission control, alternative fuel, and hybrid electric drive technologies as part of its ongoing effort to provide environmentally friendly bus service. The New York State Department of Environmental Conservation (DEC) has joined with the MTA and Environment Canada in evaluating this program, and has established a protocol for measuring both regulated and unregulated emissions, as well as other operational parameters. This paper compares and contrasts the emissions of buses powered by Detroit Diesel Series 50 diesel engines and Series 50G Compressed Natural Gas (CNG) engines. All buses have been tested for regulated emissions at the Emissions Research and Measurement Division of Environment Canada, in Ottawa, Ontario. Unregulated emissions measurements, including particle size distributions and chemical analysis, have been supported by DEC staff.

Recent evidence has linked vehicle catalysts to nitrous oxide emissions. As the population of catalyst-equipped vehicles increases, so does the need for a better understanding of this powerful greenhouse gas. Nitrous oxide measurements were made on fourteen vehicles over the FTP urban and highway cycles utilizing an FTIR analyzer. To quantify emissions from aged catalysts, emphasis was placed on testing in-use vehicles with oedometer readings between 30,000 and 120,000 kilometres. Tailpipe N2O emissions averaged 126 mg/mile for the nine aged catalyst vehicles and 74 mg/mile for the five new catalyst cars. These results are about two times greater than previous N2O studies using the FTP cycle. Also, twice as much N2O was produced during the urban driving cycle, than during the highway cycle. Based on our measurements, N2O emissions from light duty vehicles in Canada were estimated to range from 8 to 20 kilotonnes for 1992.

The recent tightening of emission standards for new heavy duty engines has lead to the development and implementation of alternative fuel engines, particularly for urban transit bus applications. Alternative fuels are intended to offer a potential emissions benefit with regards to the regulated emissions, and especially the particulate matter, which has received the greatest degree of regulatory action. However, the entire composition of the engine emissions should be considered when evaluating the environmental benefits of these new fuels, and also the continued performance of these engines in actual fleet service. In this study the exhaust emissions from methanol, ethanol, and diesel - powered buses were determined during transient operation of the vehicles on a heavy duty chassis dynamometer. The tests of the alcohol fuelled buses, and a control diesel bus were conducted as the buses accumulated mileage in revenue generating service.