Search Results

During the last years extensive work has been done to design and develop the Closed-Loop Air Revitalization System ARES. The potential of ARES e.g. as part of the ISS ECLSS is to significantly reduce the water upload demand and to increase the safety of the crew by reducing dependence on re-supply flights. The design is adapted to the interfaces of the new base lined Russian MLM module as possible location for a future installation of ARES. Due to the lack of orbital support equipment and interfaces to a waste water bus, to a feed water supply line and due to the availability of only one single vent line it was necessary to make the ARES process water loop as independent as possible from the host vehicle. Another optimization effort was to match the CO2 desorption profile with the available hydrogen flow to achieve a sufficient water recovery performance, while meeting all related safety requirements, minimizing complexity and improving reliability.

European Space Agency (ESA) has planned two important missions for performing astronomical investigations in the infrared and sub-millimetre wavelength range: ♦Herschel satellite has an observatory type mission and is the fourth cornerstone mission (CS4) of the “Horizon 2000” programme. It will carry three instruments (HIFI, SPIRE, and PACS) for high and medium resolution spectroscopy, imaging and photometry over the sub-millimetre and far-infrared range. A 3.5 m telescope will focus the incoming radiation on the Focal Plane Units of these instruments. ♦Planck satellite has a survey type mission and is the third Medium mission (M3) of the “Horizon 2000” programme. It will provide a definitive high-angular resolution map of the cosmic microwave background anisotropies over at least 95% of the sky and over a wide frequency range. A 1.5 m telescope will focus the incoming radiation on the focal plane shared by the two instruments (LFI and HFI).

ESA has been developing regenerative physicochemical air revitalisation technology for more than 20 years. The effort is now maturing into a flight demonstration experiment which is planned to be located in the Columbus module on ISS. The experiment shall be sized for a crew of three. It will comprise a CO2 concentration assembly, a Sabatier reactor and an electrolyser. The paper describes the adaptation of ARES to the available Columbus interfaces as well as ARES development status, performances, benefits to the ISS and operational agreements with ISS partners.

The aim of this study was to explore if fingernail delamination injury following EMU glove use may be caused by compression-induced blood flow occlusion in the finger. During compression tests, finger blood flow decreased more than 60%, however this occurred more rapidly for finger pad compression (4 N) than for fingertips (10 N). A pressure bulb compression test resulted in 50% and 45% decreased blood flow at 100 mmHg and 200 mmHg, respectively. These results indicate that the finger pad pressure required to articulate stiff gloves is more likely to contribute to injury than the fingertip pressure associated with tight fitting gloves.

EADS SPACE Transportation GmbH designed, built and tested a condensate buffer to be located between a Condensing Heat Exchanger (CHX) and a Condensate Water Separator Assembly (CWSA), as part of the ECLSS of the European Columbus Module. Under zero-g conditions, the separation of water from an air-water mixture is always difficult, especially if a passive device is to be used such as the low power consuming Columbus CWSA. The additional buffer volume reduces condensate water peaks reaching the CWSA to a level that excludes an overloading of the CWSA and a release of free water droplets into the air return to the cabin. In the CHX/CWSA system this may only be necessary under worst case operational conditions and with a failure of the qualified hydrophilic coating of the CHX. The buffer design principle was confirmed via prior analyses and on-ground testing. The performance of such a condensate buffer under micro-g conditions was verified during parabolic flights.

This paper describes a design proposal for adapting the OGEGU Food Production Unit (FPU) to the surface of Mars in order to produce up to 40% of the diet for a six-member crew by growing a pre-defined set of vegetable food species. The external structure, lighting system and plant support system are assessed using ESM analysis. The study shows that the mass of an FPU operating on the Mars surface, featuring an opaque inflatable structure plus all the required subsystems and equipment, is in the order of 14,000 kg. The required volume is around 150 m3 and the power consumption is around 140 kW. A reduction of c. 20 kW could be obtained by exploiting natural light using transparent materials. Finally, the paper concludes with the identification of some technological gaps that need to be investigated further for the purpose of establishing a feasible FPU on Mars.