Search Results

Engine-out HC emissions from a PFI spark ignition engine were measured using a gas chromatograph and a flame ionization detector (FID). Two port fuel injectors were used respectively for ethanol and gasoline so that the delivered fuel was comprised of 0, 25, 50, 75 and 100% (by volume) of ethanol. Tests were run at 1.5, 3.8 and 7.5 bar NIMEP and two speeds (1500 and 2500 rpm). The main species identified with pure gasoline were partial reaction products (e.g. methane and ethyne) and aromatics, whereas with ethanol/gasoline mixtures, substantial amounts of ethanol and acetaldehyde were detected. Indeed, using pure ethanol, 74% of total HC moles were oxygenates. In addition, the molar ratio of ethanol to acetaldehyde was determined to be 5.5 to 1. The amount (as mole fraction of total HC moles) of exhaust aromatics decreased linearly with increasing ethanol in the fuel, while oxygenate species correspondingly increased.

The gasoline direct injection (GDI) engine particulate emission sources are assessed under cold start conditions: the fast idle and speed/load combinations representative of the 1st acceleration in the US FTP. The focus is on the accumulation mode particle number (PN) emission. The sources are non-fuel, combustion of the premixed charge, and liquid fuel film. The non-fuel emissions are measured by operating the engine with premixed methane/air or hydrogen/air. Then the PN level is substantially lower than what is obtained with normal GDI operation; thus non-fuel contribution to PN is small. When operating with stoichiometric premixed gasoline/air, the PN level is comparable to the non-fuel level; thus premixed-stoichiometric mixture combustion does not significantly generate particulates. For fuel rich premixed gasoline/air, PN increases dramatically when lambda is less than 0.7 to 0.8.

Astrium investigates Methane Pyrolysis in the perspective of long-duration exploration missions. In particular this process, which recovers Hydrogen from Methane, allows reaching the maximum closure level of the Air Revitalization System ARES. Past studies were reviewed in the light of today's technical advancement and a technology trade-off, supported by bread boarding, is performed. Current activities do concentrate on Critical technology selection and feasibility demonstration including bread boarding and testing, Methane Pyrolysis Assembly (MPA) operational interfaces with ARES Potential applications of MPA for other exploration capabilities, like in-situ resources utilization (Moon and Mars) The paper presents the achievements so far.

Astrium investigates Methane Pyrolysis in the perspective of long-duration exploration missions. In particular this process, which recovers Hydrogen from Methane, allows reaching the maximum closure level of the Air Revitalization System ARES, see figure 1. Past studies as presented in ref. /1/ had been reviewed in light of today's technical advancement and a technology trade-off, supported by bread boarding, resulting in the pre selection of the plasma technique to perform the Methane Pyrolysis. In parallel two methods for plasma provision are investigated: Direct Current Plasma, sustained by a discharge arc rotating in a nozzle to supply energy to the flowing through carrier gas. Micro Wave (MW) Plasma, sustained by a MW within a Quartz tube embedded in a MW resonator cuboid Study activities did concentrate on Development testing of pre selected plasma Pyrolysis technology.

EADS SPACE Transportation investigates Methane Pyrolysis in the perspective of long-duration exploration missions. In particular this process, which recovers Hydrogen from Methane, allows reaching the maximum closure level of the Air Revitalization System ARES. Past studies are reviewed in the light of today's technical advancement and a technology trade-off, supported by breadboarding, is performed. Accordingly, current activities do concentrate on Critical technology selection and feasibility demonstration including breadboarding and testing, Methane Pyrolysis Assembly (MPA) operational interfaces with ARES Potential applications of MPA for other exploration capabilities, like in-situ resources utilization (Moon and Mars) The paper presents the achievements so far.

The chemistry of unburned hydrocarbon oxidation in SI engine exhaust was modeled as a function of temperature and concentration of unburned gas for lean and rich mixtures. Detailed chemical kinetic mechanisms were used to model isothermal reactions of unburned fuel/air mixture in an environment of burned gases at atmospheric pressure. Simulations were performed using five pure fuels (methane, ethane, propane, n-butane and toluene) for which chemical kinetic mechanisms and steady state hydrocarbon (HC) emissions data were available. A correlation is seen between reaction rates and HC emissions for different fuels. Calculated relative amounts of intermediate oxidation products are shown to be consistent with experimental measurements.

The engine-out (EO) total and speciated hydrocarbon emissions data from the Auto-Oil Program Phase II Heavy Hydrocarbon Study had been analyzed. The methodology was to first investigate the stabilized EO emissions (Bag 2) of a specific vehicle (Vehicle 04B, a 1989 Model Year Ford Taurus); then the vehicle-to-vehicle differences in Bag2 emissions were considered. Finally, the differences in the Bag2 and the starting/warm-up EO emissions (Bag1) were examined. The speciated emissions may be interpreted as a “feed-through” part due to the unreacted fuel species, and an “offset” part due to the decomposition products. The significant non-fuel emitted species were methane and the olefins. The HC emissions for vehicles with different total emissions were similar in species composition. For both the total and speciated emissions, there was no substantial difference between the Bag1 and Bag2 values for Vehicle 04B.

A technique has been developed to measure the desorption and subsequent oxidation of fuel in the oil layer by spiking the oil with liquid fuel and firing the engine on gaseous fuel or motoring with air. Experiments suggest that fuel desorption is not diffusion limited above 50 °C and indicated that approximately two to four percent of the cylinder oil layer is fresh oil from the sump. The increase in hydrocarbon emissions is of the order of 100 ppmC1 per 1% liquid fuel introduced into the fresh oil in a methane fired engine at mid-speed and light load conditions. Calculations indicate that fuel desorbing from oil is much more likely to produce hydrocarbon emissions than fuel emerging from crevices.

The use of hydrogen as a fuel supplement for lean-burn engines at higher compression ratios has been studied extensively in recent years, with good promise of performance and efficiency gains. With the advances in reformer technology, the use of a gaseous fuel stock, comprising of substantially higher fractions of hydrogen and other flammable reformate species, could provide additional improvements. This paper presents the performance and emission characteristics of a gas mixture of equal volumes of hydrogen, CO, and methane. It has recently been reported that this gas mixture can be produced by reforming of ethanol at comparatively low temperature, around 300C. Experiments were performed on a 1.8-liter passenger-car Nissan engine modified for single-cylinder operation. Special pistons were made so that compression ratios ranging from CR= 9.5 to 17 could be used. The lean limit was extended beyond twice stoichiometric (up to lambda=2.2).