Search Results

Thermally-sprayed, composite coatings have been developed and sprayed on aluminum engine heads to replace powdered metal valve seat inserts. The process uses a conventional two-wire arc (TWA) gun with nickel and iron-based wire feedstocks. A unique surface preparation technique was developed to assure excellent coating adhesion. A composite Fe/Fe3O4/Ni/NiO/CrO coating was dynamometer tested using a single-cylinder Rotax engine, and showed improved wear performance over a conventional powdered-metal insert. Details of surface preparation, coating development, tribological properties and engine testing are described in this work.

Individual hydrocarbon conversion efficiencies of engine-out emissions have been measured for four different catalyst formulations (Pd-only, trimetallic, Pd/Rh, and Pt/Rh) during stoichiometric and rich operation. The measurements were carried out as a function of fuel-air equivalence ratio (Φ) using a dynamometer-controlled 1993 Ford V8 engine and capillary gas chromatography. HC conversion efficiency was examined in terms of mass conversion efficiency and also using three new definitions of catalyst conversion efficiency. The efficiencies across the four catalysts show similar trends with Φ for almost all HC species. The catalyst efficiencies for alkanes, alkenes, and aromatic species decrease as Φ increases above stoichiometric: alkane efficiencies decrease faster than alkenes which in turn decrease faster than aromatics. All efficiencies fall to zero near Φ = 1.08 except those of MTBE and acetylene, which remain near 100%.

This study was performed to quantify the effects of injector targeting and fuel volatility on transient A/F excursions and fuel film mass in a port fuel injected (PFI) engine. Two injector targeting positions as well as injection timing and four different fuels were studied. Warm-up tests were performed with the throttle ramped between two positions over a one second interval to provide smooth changes in airflow and injected fuel. The exhaust A/F was recorded for each transient and fit using the X-τ model to estimate the change in the liquid fuel stored in the port and cylinder due to the throttle ramp. The change in fuel stored in the films was: ∼20% less with valve targeting ∼30% less with IVO injection timing 50-100% higher for hesitation fuel

In 1999, the first generation NOx sensor from NGK Spark Plug, Co., Ltd. was commercialized for use in gasoline LNT NOx after-treatment systems [ 1 ]. Since then, as emissions regulations and OBD requirements have become more stringent, the demand for a high-accuracy NOx sensor with fast light-off has increased, particularly for diesel after-treatment systems. To meet such market demands, NGK Spark Plug, Co., Ltd. has developed, in collaboration with Ford Motor Company, a second generation NOx sensor.

This paper summarizes the first phase of an experimental effort focused on developing a comprehensive understanding of the in-cylinder air/fuel mixing and combustion processes in spark-ignition engines using laser-based fuel distribution and combustion measurements. As part of this first phase, a semi-quantitative, laser-induced fluorescence, fuel distribution measurement technique was developed and demonstrated. The calibration, correction, and image analysis processes associated with the technique were shown to be comparatively simple and effective (relative to other analytical and empirical methods). The error associated with the technique was shown to be 5 - 10 % under vapor phase conditions. This work was applied to a port fuel injected optical engine, which was designed for optical access through the piston and cylinder liner under firing conditions.

This paper describes the reduction of cyclic combustion variations in spark-ignited engines, especially under idle conditions in which the air-fuel mixture is lean of stoichiometry. Under such conditions, the combination of residual cylinder gas and parametric variations (such as variations in fuel preparation) gives rise to significant combustion instabilities that may lead to customer-perceived engine roughness and transient emissions spikes. Such combustion instabilities may preclude operation at air-fuel ratios that would otherwise be advantageous for fuel economy and emissions. This approach exploits the recognition that a component of the observed combustion instability results from a noise-driven, nonlinear deterministic mechanism that can be actively stabilized by small feedback control actions which result in little if any additional use of fuel.

In this paper, the formability of AA5754 aluminum laser-welded blanks produced by Nd:YAG laser welding is investigated under biaxial straining conditions. The mechanical behavior of the laser-welded blanks is first examined by uniaxial tensile tests conducted with the weld line perpendicular to the tensile axis. Shear failure in the weld metal is observed in the experiments. Finite element simulations under generalized plane strain conditions are then conducted in order to further understand the effects of weld geometry and strength on the shear failure and formability of these welded blanks. The strain histories of the material elements in the weld metal obtained from finite element computations are finally used in a theoretical failure analysis based on the material imperfection approach to predict the failure strains for the laser-welded blanks under biaxial straining conditions.

Nonthermal plasma discharges in combination with catalysts are being developed for diesel aftertreatment. NOx conversion has been shown over several different catalyst materials. Particulate removal has also been demonstrated. The gas phase chemistry of the plasma discharge is described. The plasma is oxidative. NO is converted to NO2, CH3ONO2 and HNO3. Hydrocarbons are partially oxidized resulting in aldehydes and CO along with various organic species. Soot will oxidize if it is held in the plasma. When HC is present, SO2 is not converted to sulfates. Suitable plasma-catalysts can achieve NOx conversion over 70%, with a wider effective temperature range than non-plasma catalysts. NOx conversion requires HC and O2. Electrical power consumption and required exhaust HC levels increase fuel consumption by several percent. A plasma catalyst system has demonstrated over 90% particulate removal in vehicle exhaust.

Environmental concerns have prompted increasingly stringent government legislation regulating automotive fuel economy and emissions. Recent rules not only mandate lower total emissions, but also require on-board diagnostics which monitor the vehicle exhaust systems. In order to satisfy these requirements, new and improved exhaust gas sensors are continually being developed to serve as part of the engine feedback control and emissions monitoring systems. Before we can properly design these new sensors, we must attempt to better understand the harsh environment in which they will operate. In this paper, we examine the high frequency nature of pressure fluctuations found in the exhaust system for both steady state and transient engine operating conditions. We also investigate temperature fluctuations, but restrict these measurements to the sampling environment found in the packaging of a Ford Si-based microcalorimeter.

Ford Motor Company is participating in the Department of Energy's (DOE) Ultra-Clean Transportation Fuels Program with the goal to explore the development of innovative emission control systems for advanced compression-ignition direct-injection (CIDI) transportation engines. CIDI (or diesel) engines have the advantages of a potential 40% fuel economy improvement and 20% less CO2 emissions than current gasoline counterparts. To support this goal, Ford plans to demonstrate an exhaust emission control system that provides high efficiency particulate matter (PM) and NOx reduction. Very low sulfur diesel fuel will be used to enable low PM emissions, reduce the fuel economy penalty associated with the emission control system, and increase the long-term durability of the system. The end result will allow vehicles with CIDI engines to be Tier II emissions certified at a minimum cost to the consumer.

Diesel vehicles have significant advantages over their gasoline counterparts including a more efficient engine, higher fuel economy, and lower emissions of HC, CO, and CO2. However, NOx control is more difficult on a diesel because of the high O2 concentration in the exhaust, making conventional three-way catalysts ineffective. The most promising technology for continuous NOx reduction onboard diesel vehicles is Selective Catalytic Reduction (SCR) using aqueous urea. Recent work with urea SCR has involved aftertreatment for the 1.2L DIATA common-rail diesel engine. This engine was used in Ford's hybrid-electric vehicle, the Prodigy, which was developed under the PNGV (Partnership for a New Generation of Vehicles) program. An emission control system consisting of a diesel particulate filter followed by an underbody SCR system was used successfully to meet ULEV emission standards (0.2 g/mi NOx, 0.04 g/mi particulate matter (PM)).

A traction test machine, developed for evaluation of traction-CVT fluids for the automotive consortium, USCAR, provides precision traction measurements to stresses up to 4 GPa. The high stress machine, WAMhs, provides an elliptical contact between AISI 52100 steel roller and disc specimens. Machine stiffness and positioning technology offer precision control of linear slip, sideslip and spin. A USCAR traction test methodology includes entrainment velocities from 2 to 10 m/sec and temperatures from -20°C to 140°C. The purpose of the USCAR machine and test methodology is to encourage traction fluid development and to establish a common testing approach for fluid qualification. The machine utilizes custom software, which provides flexibility to conduct comprehensive traction fluid evaluations.

Risk curves are developed for several crash data sets, expressing the probabilities of injury as a function of HIC, Extension Moment, Neck Tension and Maximum Deflection, respectively. The statistical method uses concept of thresholds that are interval censored and right censored. A combined evaluation method is used to select a “best” curve among the curves derived from various methods.

A diesel fuel and air diffusion flame burner system has been designed for laboratory simulation of diesel exhaust gas. The system consists of mass flow controllers and a fuel pump, and employs several unique design and construction features. It produces particulate emissions with size, number distribution, and morphology similar to diesel exhaust. At the same time, it generates NOx emissions and HC similar to diesel. The system has been applied to test plasma discharges. Different design discharge devices have been tested, with results indicating the importance of testing devices with soot and moisture. Both packed bed reactor and flat plate dielectric barrier discharge systems remove some soot from the gas, but the designs tested are susceptible to soot fouling and related electrical failures. The burner is simple and stable, and is suitable for development and aging of plasma and catalysts systems in the laboratory environment.

Seated vertical vibration thresholds were tested using an adaptive Levitt algorithm. All such testing raises issues concerning potential shifting of thresholds during testing as subjects improve at the task. Additional testing was done at 4 and 16 Hz to quantify the adequacy of training within the algorithm. A 3-down 1-up algorithm starting at 8 mG descended in 3 dB steps until the first error, then switched to 1 dB steps and continued for 9 more reversals, with the last 6 averaged for threshold. Stimuli were paired with intervals containing no vibration in random order. Subjects closed their eyes and were presented with sounds in earphones to indicate the stimulus intervals, and chose the interval they thought contained the stimulus. A combination of eyes closed for concentration, gradual approach to the threshold, 4 reversals before data was used, and feedback on each trial provided built-in training to avoid threshold shift.

The present research is concerned with the quality of the shearing process, which is an integral part of automotive vehicle body stamping. Experiments were done to analyse the influence of the gap between the cutting edges and the geometry of the cutting blades, on the quality of the sheared surface. Experimental results are presented as microstructures of polished samples. To predict the quality of sheared surfaces, a numerical code based on solid mechanics equations, elastoplastic flow theory and cummulative theory of damages was created.

In-cylinder pressure traces vary significantly from cycle-to-cycle in spark-ignition (SI) engines. The variations, substantially present even when engine is stable, are magnified under certain engine operating conditions. As a result, engine torque output oscillates and engine operation becomes unstable. EGR tolerance, lean burn limit and spark retard capabilities at CSSRE (Cold Start Spark Retard and Enleanment) are mostly determined by the levels of cycle-to-cycle variations. None of the engine computer models, however, have included cyclic variations for routine industrial applications. As the application domain of engine simulation models expands into unstable engine operating conditions, the modeling of cyclic variations becomes increasingly important. In this research, reviews were conducted regarding different approaches for the simulation of cyclic variation.

Previously reported experiments revealed the presence of a small number of clusters or very small particles in the effluent of a nonthermal plasma reactor when treating a simulated engine exhaust mixture. These clusters are smaller than 7 nm. The quantity of clusters is orders of magnitude smaller than the particulate diesel or gasoline engine exhaust typically contains. In this report, we describe further experiments designed to determine the chemical composition of the clusters. Clusters were collected on the surface of a silicon substrate by exposing it to the effluent flow for extended time periods. The resulting deposits were analyzed by high mass resolution SIMS and by XPS. The SIMS analysis reveals NH4+, CH6N+, SO-, SO2-, SO3- and HSO4- ions. XPS reveals the presence of N and S at binding energies consistent with that of ammonium sulfate.

A planar dielectric barrier discharge device has been tested for exhaust emission reduction in simulated engine exhaust. This device's electrical characteristics have been measured and are presented in this paper. The device consists of two dielectric barriers which act like series capacitors, with the gas gap between them. At low gap voltages, the gas gap also acts like a capacitance, with a much smaller capacitance than the barriers. At higher voltages, the gas gap breaks down and a blue–purple glow visually fills the gap. The partially ionized gas conducts charge across the gap, building electrical charge on the dielectric barrier inner surface. When the AC excitation voltage peaks and starts to go toward an opposite polarity, the discharge momentarily extinguishes, trapping charge in the dielectric barrier capacitance.

Spark retard is desirable for decreasing cold start hydrocarbon emissions and lighting off the catalyst more rapidly. The focus of this work is to better understand the nature of the HC emissions as spark is retarded and investigate the location of the oxidation (in-cylinder or in the exhaust port and manifold). Fast FID measurements were taken in the exhaust port of a single cylinder research engine during cold, retarded spark engine operation (1200 rpm, 2.5 bar IMEP, 20 °C fluids). At moderate spark retard both Fast FID (exhaust port) and exhaust plenum HC levels decreased due to reduced crevice volume fraction at the end of burn, and increased in-cylinder burn up. In contrast, at large spark retard the port HC's increased dramatically while the exhaust plenum levels continued to fall to near zero. This is thought to be due to the onset of incomplete in-cylinder combustion along with increased exhaust port and manifold after-burning caused by the increasing exhaust gas temperatures.