Search Results

Initial preliminary development phases of two distinct SP-100 control drive assembly bearing test programs were successfully completed at elevated temperature in vacuum. The first was for the reflector drive line spherical self-aligning bearings. Each bearing consisted of a carbon-graphite ball mounted on an aluminum oxide-coated Ta-10%W shaft, captured by an aluminum oxide-coated Ta-10%W socket. One set of these bearings was exposed to temperatures up to 1180K (1665°F) at 1.33x10-6 Pa (1x10-8 torr) and subjected to 38000 cycles of motion. Friction coefficients were found to be between 0.11 and 0.25 over the full range of operation. Overall performance of the bearings was excellent, with only slight wear observed. The second test program was for the safety rod slider bearing. Zirconium carbide coated Nb-1%Zr bearing pads were stroked inside a molybdenum tube at temperatures up to 1422K (2100°F) at ∼1.33x10-6 Pa with a normal load of 1.02 Kg between each sliding surface.

This paper describes the design, implementation, and performance test results of an engineering model of the Position Multiplexer (MUX)-Analog Input Processor (AIP) System for the transmission and continuous measurements of Reflector Control Drive position in SP-100. The specially tailored MUX-AIP combination multiplexes the sensor signals and provides an increase in immunity from low frequency interference by translating the signals up to a higher frequency band. The modulated multiplexed signals are transmitted over a single twisted shielded cable pair from the reflector drives located near reactor to the AIP located at the power conditioning/system controller end of the space craft boom. There the signals are demultiplexed and processed by the AIP, eliminating the need for individual cables for each of the twelve position sensors across the boom.

The SP-100 reactor will operate at temperatures up to 1500K in high vacuum. Development of bearing coatings is necessary to avoid self welding and/or galling of moving components. No experience base exists for these conditions-the early SNAP (Space Nuclear Auxiliary Power) program requirements were over 400K lower with shorter lifetime requirements. To address the SP-100 needs, a tribology development program has been established at GE to investigate candidate coating materials. Materials were selected based on their high thermodynamic stability, high melting point, compatibility with the substrate, and coefficients of thermal expansion similar to niobium-1% zirconium - the candidate structural material for SP-100. An additional requirement was that the deposition processes should be commercially available to coat large components.

Recent Generic Flight System (GFS) updates have necessitated revisions in the initial startup and restart control strategies. The design changes that have had the most impact on the control strategies are the addition of the Auxiliary Cooling and Thaw (ACT) system for preheating the lithium filled components, changes in the reactivity worths of the reflectors and safety-rods such that initial cold criticality is achieved with only a small amount of reflector movement following the withdrawal of the safety-rods, and the removal of the scram function from the reflectors. Revised control and operating strategies have been developed and tested using the SP-100 dynamic simulation model, ARIES-GFS. The change in the total reactivity worths of the reflectors and safety-rods has eliminated the need for the use of fast and slow reflector drive speeds during the initial on-orbit approach to criticality.

As part of the SP-100 Space Reactor Power System Program being undertaken for the U. S. Department of Energy, GE is developing a thermoelectric (T/E) power converter which utilizes reactor delivered heat and transforms it into usable electric power by purely static means. This converter is based to GE's product line of successful thermoelectric space power systems. The SP-100 power converter embodies the next generation improvement over the type of T/E converter successfully flown on the six U. S. space missions. That is, conduction coupling of T/E cell to both the heat source and the heat rejection elements. The current technology utilizes radiation coupling in these areas. The conduction coupling technique offers significant improvements in system specific power since it avoids the losses associated with parasitic ΔT's across the radiation gap between the heat source and the hot junction of the thermoelectric (T/E) cell.

The SP-100 Space Reactor Power System is being developed by GE, under contract to the U.S. Department of Energy, to provide electrical power in the range of 10's to 100's of kW. The system represents an enabling technology for a wide variety of earth orbital and interplanetary science missions, nuclear electric propulsion (NEP) stages, and lunar/Mars surface power for the Space Exploration Initiative (SEI). An effective infrastructure of Industry, National Laboratories and Government agencies has made substantial progress since the 1988 System Design Review. Hardware development and testing has progressed to the point of resolving all key technical feasibility issues. The technology and design is now at a state of readiness to support the definition of early flight demonstration missions. Of particular importance is that SP-100 meets the demanding U.S. safety, performance, reliability and life requirements.

The term “SP-100” is synonymous with a set of technologies that can be utilized to provide long lifetime, reliable, safe space power over the range of kilowatts to megawatts [1] using a nuclear reactor as the heat source. This paper describes recent development progress in a number of technology areas such as fuel, materials, reactivity control mechanisms and sensors. Without exception, excellent technical progress is being accomplished in all areas under development to optimize spacecraft performance characteristics.

Early flight mission objectives can be met with a Space Reactor Power System (SRPS) using thermoelectric conversion in conjunction with fast spectrum, lithium-cooled reactors. This paper describes two system design options using thermoelectric technology to accommodate an early launch. In the first of these options, radiatively coupled Radioisotope Thermoelectric Generator (RTG) unicouples are adapted for use with a SP-100-type reactor heat source (Deane 1992). Unicouples have been widely used as the conversion technology in RTGs and have demonstrated the long-life characteristics necessary for a highly reliable SRPS (Hemler 1992). The thermoelectric leg height is optimized in conjunction with the heat rejection temperature to provide a mass optimum 6-kWe system configured for launch on a Delta II launch vehicle. The flight-demonstrated status of this conversion technology provides a high confidence that such a system can be designed, assembled, tested, and launched by 1996.

The work reported in this paper has been conducted by a team from GE-Aircraft Engines, GE-CR&D, and Sundstrand under a contract sponsored by the USAF, Wright Laboratories, WPAFB, Contract No. F33615-90-C-2052. The objective of this contract is to prove the feasibility of an Integral Starter/Generator (IS/G) through the preliminary design stage and demonstrate the starter/ generator technology in the externally mounted version utilizing switched reluctance machine technology. This paper will report on the progress for the EIS/G-system through the initial testing stage. Comparison of the finished hardware with the design results presented earlier will lead of the paper. This is followed by the discussion of the early testing results for the system testing. Recommendation on additional testing will be presented at the end of the paper.

Measurement of dimensional characteristics of airfoil parts is primarily a manual, labor intensive operation. It employs a wide variety of gages that vary from very expensive optical comparitors to inexpensive pin gages. An automatic non-contacting inspection gage capable of measuring most dimensional characteristics would be cost effective, simplify inspection operations, consolidate a number of gages into one, and improve overall inspection reliability by minimizing human involvement. This paper presents the results of the design and development of a demonstrator semi-automatic laser gage dimensional inspection system that addresses this problem.

The advantages of infinitely variable ratio steering and propulsion for track laying vehicles are well known. Studies and demonstrator programs in the past decade have indicated that the hydromechanical transmission has the most promise of providing infinitely variable ratio for military vehicles. In 1966 the Army launched a program to develop the hydromechanical transmission to “production ready” status. This paper describes that program, the transmission selected, and some of the problems encountered in the transition from the demonstrator stage to one of readiness for military application.

Aircraft starting and generating systems heretofore have been largely the result of joining together available components. Recent studies have demonstrated that substantial benefits in weight, cost, size, and performance may be realized through a total system approach. This paper identifies the types of information required, and the methods of system analysis employed, to design an optimized system.

The principal design features of the NASA QCSEE UnderThe-Wing and Over-The-Wing powered lift propulsion systems are given. In the UTW engine, these include noise reduction features, a variable pitch low pressure ratio fan, a fan drive reduction gear, an advanced core and low pressure turbine with a low pollution combustor, a digital control, and advanced composite construction for the inlet, fan frame, fan exhaust duct, and variable area fan exhaust nozzle. The OTW engine is similar but has higher fan pressure and a fixed pitch fan. Both engines are scheduled to be fabricated and tested starting in 1976.

A new ultrathin-backed semipermeable membrane has been developed which shows considerable promise as a gas separator for engine bleed air to provide nitrogen-rich air for aircraft fuel tank inerting. The membrane is a silicone, polycarbonate copolymer of 1500 Å effective thickness, deposited on a reinforced porous backing. The selective removal of oxygen provides oxygen concentrations of less than 9% in the inerting gas. Small-scale testing demonstrated that the backed membranes are suitable in the aircraft environment. A system using such membranes avoids the logistic and service requirements of tanked liquid nitrogen.

Previous studies had demonstrated the economic and technical feasibility of producing high-quality forgings for aircraft turbine engine parts from hot-isostatically pressed (HIP) Rene 95 powder billets. The present program was aimed at developing a production practice for making HIP + forged turbine discs. The major goal was improved product fabricability and reliability with minimum cost. The program was conducted using argon atomized Rene 95 powder. Experimental studies were conducted to evaluate the effect of powder characteristics, HIP parameters, preform design, and forging conditions on forgeability, microstructure, and mechanical properties. The results of these studies were incorporated into a pilot production run in which 10 disc forgings were made and evaluated. The selected process involved the consolidation of -60 mesh powder to full density by hot-isostatic pressing at a temperature above the γ' solvus temperature.

A method for measurement of rolling resistance of vehicles using only a single accelerometer measurement has been developed and a simple instrument has been constructed. Results of typical measurements on large, electrically propelled off-highway trucks are discussed.

THE “Orion” gas-generator turbocompound engine consists of a supercharged, regenerative aircooled, 2-stroke-cycle opposed-piston diesel engine driving two centrifugal compressors. One of these compressors is for combustion air with fine air filtration, while the other is for cylinder cooling with much less filtration. The gas-generator engine has a bore of 4¼-in. diameter and a stroke of 5⅞ in. × 2. The engine turns at 2340 rpm, and the combustion air compressor turns at 37,000 rpm while the cooling air compressor turns 17,000 rpm. The cylinder is cooled with air at nearly the supercharge level and at an equivalent temperature because this air later does work on the turbine. The cooling airflow is about 3½ times the combustion airflow. These two airstreams join in a plenum chamber downstream from the engine, and the mixture temperature is about 500 F. This hot gas stream then goes to the power turbine, which is mechanically free of the gas generator.

The major technological developments which have made possible the trend towards higher temperatures in modern aircraft gas turbine engines are discussed. The relative importance of manufacturing processes, material developments, cooling techniques, analytical design procedures, rupture and cyclic life considerations, and aerodynamic and mechanical design improvements are discussed along with illustrative examples and technical data. The need for a balanced design approach is stressed, and examples are given where trade-offs can be made. It is noted that the advances in aircraft engines during the last 10 years have been based on the evolution of sound engineering principles, extensive component and engine development, and careful consideration of the operational requirements rather than a tremendous breakthrough or revolutionary concept in any one area.

A four-legged, 3000 lb, walking truck test bed has been developed and the test results have proved the feasibility of walking machines. Effectiveness of this control method where the machine mimics man’s arm and leg movements was shown by a variety of maneuverability experiments. Therefore, it has been proved that it is possible to develop this vehicle concept, and the control method involved, to effectively emulate animals in the way they travel on rough terrain. Human perception, judgment, and agility are transmitted through the machine in a manner that lets the operator easily imagine that the machine is merely an effective extension of his own appendages. The human psychomotor action, coupled with the power and ruggedness of the machine, provides a valuable marriage. It opens new vistas not only for rough terrain vehicles but also for a variety of other manipulative machines. Many jobs require the sensing acuity of man but are too tough for the frail human flesh.

This paper discusses some of the objectives, results, and implications of GE's electric vehicle and component systems developments to date. The experimental vehicle is covered in detail. The vehicle's styling, construction, materials, power system, operating costs, and performance are discussed with some alternatives and attendant economic considerations. The paper also presents a brief discussion of the power system requirements, performance, and economics of several potential electric vehicles as well as a critique of the potential power sources presently announced as having promise for electric vehicle propulsion. The paper includes pictures, tables, and graphs describing the experimental vehicle and illustrating the points discussed relative to other potential vehicles, power systems, batteries, and fuel cells.