Search Results

Since the sizes of the flywheel and clutch have been enlarged due to downsizing of diesel engines, the mass and moment of inertia at the crankshaft rear end have increased. Consequently, the serious bending stresses have appeared in the crankshaft rear. This paper describes the characteristics of those serious bending stresses, based on the mechanism for whirl resonance. The whirl resonance is largely impacted by the mass of the flywheel and clutch and by the distance from the crank-journal center of the rear end to the center of gravity of the flywheel and clutch.

Improving idle sound quality as well as reducing idle noise level is increasingly demanded for diesel engines. Therefore, unusual noise occurrence at idle is a serious problem, and the noise must be removed. This paper describes the characteristics and mechanism of ticking noise that is unusual noise radiated from the journal bearing of the camshaft at low idle speeds, based on the mechanism of cavitation in oil film existing between the journal and bearing.

Using skirt-liner clearance and cylinder pressure measurements provided by Isuzu Motors, Ltd. of a production type gasoline automotive engine, a validation study was done of Ricardo's PISDYN code, which predicts the secondary motions and skirt liner elastohydrodynamic lubrication of pistons. Predictions using the computer code of the skirt liner clearance at two locations on the skirt were compared with measured results. Using the code, parametric studies were done. Very good qualitative and quantitative agreement was found for the baseline cases. In the parametric studies using the code only, the following were found: The predicted clearances were very sensitive to variation in cold minimum clearance. The effect of cylinder induced pressure deformation was significant, especially near the point of peak cylinder pressure. Increasing the cylinder pressure increased the peak clearances. Changing the asperity roughness height affected the clearances near a point of asperity contact only.

The noise of diesel engines operating at low idle is an important noise evaluation criterion in both commercial vehicles and passenger cars. At low idle, a quiet, pleasant noise is required. Accordingly, unusual noise occurrence at low speed is a serious problem, and the noise must be prevented. In this paper, characteristics of the stick-slip noise, which is an unusual noise that radiates from the oil seal at low idle and the generating mechanism of the stick-slip noise in the six-cylinder-inline diesel engine are discussed. In addition, a method to prevent the stick-slip noise is presented.

Countour Induction Hardening (CIH) method is in the limelight as a new possible surface refining method for gears as it reduces quenching distortion considerably and increases compressive residual stress. Also, Double Shot Peening (DSP) method, especially its advanced technique of using extensively small shots (less than 100 m) at the secondary peening, enables increased compressive residual stress under the surface of the gears. Therefore, the new Compound Surface Refining Method of using CIH + DSP is expected to give much higher compressive residual stress than the conventional methods. On studying the application of this new method, the authors evaluated their surface-refining characteristics and the fatigue limits.

A torsional damper is attached to a crankshaft to control the torsional vibration of the crankshaft system. However, the damper, which has a rubber part in between a damper mass and a damper hub, possesses a three-dimensional inertia moment and an inertia mass that could excite the crankshaft system. This paper discusses the generating mechanisms of the bending strain on the bolt to fasten the damper hub to the crankshaft, from the measured bolt strains and the measured behavior of the damper mass and the damper hub under the engine operating conditions.

In recent years, Nearfield Acoustical Holography (NAH) has been used to identify stationary vehicle exterior noise sources. However that application has usually been limited to individual components. Since powertrain noise sources are hidden within the engine compartment, it is difficult to use NAH to identify those sources and the associated partial field that combine to create the complete exterior noise field of a motor vehicle. Integrated Nearfield Acoustical Holography (INAH) has been developed to address these concerns: it is described here. The procedure entails sensing the sources inside the engine compartment by using an array of reference microphones, and then calculating the associated partial radiation fields by using NAH. In the second part of this paper, the use of farfield arrays is considered. Several array techniques have previously been applied to identify noise sources on moving vehicles.

Supercharging system is obviously a necessary technology for heavy duty vehicular diesel to meet future stringent emission regulation as well as to improve fuel consumption characteristics. Although the conventional exhaust turbocharger system improves fuel consumption, there are some problems such as having a difficulty in improving starting acceleration and smoke emission characteristic because the response of an exhaust supercharger is not enough. On the other hand, the conventional mechanical supercharging system seems to be a quite effective aid for acceleration ability. However, it does not satisfy demand for low fuel consumption characteristic.

Engine crankshafts have been designed to avoid low-harmonic-order resonant torsional vibration in a commonly-used engine speed range, but the authors have found that, in some engines, especially turbo-charged engines, a significant degree of a low-harmonic-order exciting torque acts on the crankshaft. In these engines, the amplitude of non-resonant low-harmonic-order torsional vibration is almost as large as that of the resonant one. The authors conclude that the 3rd-order non-resonant torsional amplitude is not only significant but also characteristic of the turbo-charged engine in comparison with the naturally-aspirated engine, and recommend that crankshafts on turbo-charged diesel engines should be made stiffer than those on naturally-aspirated engines.

GVW 20 ton class cargo trucks were mainly powerd by L6 turbocharged engines ISUZU 6SD1TC and ISUZU 6RB1TC, and this time new 6WA1TC turbocharged engine with intercooler as a successor to 6RB1TC went into production in July 1992. In the recent cargo vehicle market in Japan, demand is increasing for higher out-put power, light weight, long service life, high reliability and low fuel consumption. Under such circumstances special engineering attention was paid to exhaust emissions and noise regulations which are expected to become even stricter in future. The basic engine structure consists of an OHC 4-valve type cylinder head and a ladder frame type cylinder block which satisfies the requirements for the high out-put power, low fuel consumption and light weight. Also, adopted are various variable structures such as a high pressure fuel injection pump with a variable injection timing and rate control device, variable swirl system and variable geometry turbocharger.

There is ever an increasing need for weight reduction and high performance of engine (clean smoke and improving fuel economy) To achieve this, recently aluminum castings are used for engine parts such as cylinder heads that construct combustion chamber and are required thermal resistance. This paper describes thermal fatigue tests of aluminum castings that are made under various conditions of cooling rate during solidification, heat treatment, and chemical compositions. It further investigates the influence of material (such as cooling rate, chemical conmposition and heat treatment) and mechanical properties (such as σB, δ, E ) on thermal fatigue life of aluminum castings.

This paper shows one example of cooling system, optimized by utilizing computer simulation in the early development stage. First, a numerical simulation is conducted to obtain the air flow rate through engine compartment room by the software “STREAM”. Second, ΔTw are calculated by the software “KULI”, developed by Steyr-Daimler-Puch AG, to evaluate the original cooling system. Third, the optimization of this system is conducted by the design of experiment for cost saving and weight reduction. The test value was well matched with the calculated one and CAE was confirmed to be very helpful for saving the proto-build cost and time period.

Vibration behavior of a crankshaft in operation is complicated and difficult to simulate because of oil effects on journals, coupled vibration of crankshaft system parts, combustion and inertia acting on the crankshaft. Particularly, the stiffness and damping of oil film vary with crank angles and thus the numerical analysis must deal with nonlinear vibration. This oil film effects also diversify the vibration modes of the crankshat; the vibration modes in an actual operation differs from that in statically experiment modal analysis. This paper describes a new method developed by the author to analyses, predict, and reduce noise and vibration using several techniques including numerical simulation, finite element method, Sommerfeld concept on oil film effects, and modal frequency response.

Torsional dampers have been attached to engine crankshafts only for the control of the crankshaft torsional vibrations. However, a torsional damper is a mass-spring system of three-dimensions, so the torsional damper could exert some influence on the three-dimensional vibrations of the crankshaft system. Since the inertia ring of the torsional damper has moments of inertia and it rotates with the crankshaft, gyroscopic vibrations of the inertia ring can also be generated. For a V-type ten-cylinder diesel engine (V- 10, ϕ119 × 150), the three-dimensional vibrations of the crankshaft system were calculated by the dynamic stiffness matrix method, taking account of the influence of the gyroscopic vibrations of the inertia ring of the torsional damper. The dynamic bending stresses were measured at the fillets of both the No.1 crank journal and the No.1 crank pin in the No.1 crank throw plane.

Engine vibration is a great disadvantage of a V-type six-cylinder engine because ignition does not occur at regular intervals. The engine achieves ignition at regular intervals by having a crank pin offset crankshaft. The shape of the crank pin offset crankshaft is so complex that the location of the crank pin on which bending stress concentrates cannot be obtained easily. This paper reports on the mechanism that generates bending stresses on the crank pin, and discusses the location at which the maximum bending stress is generated with crank pin offset crankshaft.

Application of alternate fuels to diesel engine is much desired. A new and unique dual-fuel injection system has been developed for high speed automotive diesel engines. This system has two features. One is that alternate fuels such as methanol, ethanol and biomass, are directly inducted into the fuel injection pipe through one-way check valve under pressure, and blended fuels are simultaneously injected into the combustion chamber. The other is that various kinds of fuel can be easily adapted to this system not dependent upon the fuel properties such as viscosity. Using a single cylinder direct injection diesel engine and ethanol as an alternate fuel, injection characteristics and exhaust gas emissions were investigated. The results showed that ethanol could replace up to 50% of diesel fuel while keeping the normal engine operating stability. A better fuel economy was also obtained by applying both higher compression ratio and advanced injection timing.

The P’UP has been on the markets worldwide since 1972, both in Japan and overseas, including for the U.S., in which case, with model designation as the Chevrolet LUV. In 1980, for the first time since its market introduction, it was fully remodelled with detail improvements reflected thereon in every aspect. This new model continues to be on the U.S. market as the Chevrolet LUV as it has been, but, beginning from spring of 1981, the similar model has been introduced to the market by the American Isuzu Motors Inc. (AIM) as the Isuzu P’UP. Taking this opportunity, a diesel version has been added to its model lineup. The diesel engine mounted on this version features its 20 to 30% better fuel efficiency over its gasoline counterpart. In the first half of this paper, the engineering concepts of its full remodelling and their onvehicle reflection will be introduced.

A simple and easy calculation may be performed, using a three-mass vibration system model, to study the influence of an engine mounting on automobile vertical vibration. The advantage of an engine mounting of high damping rubber is confirmed by this calculation, and is further verified by using power and cross spectral analysis of an automobile random vibration. The validity of the three-mass vibration system is shown.

A pre-combustion chamber (hot plug) made of the silicon nitride ceramics has been developed. The hot plug constitutes a component of the combustion chamber of swirl chamber diesel engines. And it is subjected to the severest thermal load of all the diesel engine operating components. Unlike metal hot plugs, the ceramic hot plug application requires a unique design approach to meet the ability of the ceramic materials. That is, the soft engine mounting is necessary to avoid the concentraction of mechanical stress resulting from the high Young's Modulus of the ceramic and control of temperature distribution is also required to reduce thermal stress. Due to the heat insulating construction, the ceramic hot plug permits the combustion performance to be improved at a low speed and load, resulting in improved noise, startability, and HC emission. In additional the ceramic hot plugs are already being produced for diesel passenger car.

Eight kinds of the spot-welded test specimens were studied to obtain the basic fatigue data on steel sheets for car bodies. Analytical methods such as the strain amplitude at outside and inside plates close to the nugget, the maximum nominal stress and Kθmax criteria of fracture mechanics were used. The authors propose that the ratio of strains at two points around the nugget can provide evaluation of the bending load and estimation of the fatigue strength.