Search Results

It was found that the finger blood pulse shows various fluctuations in different driving conditions. The nature of the finger blood pulse fluctuations was used for estimating a driver's internal state. Indexes suitable for expressing the fluctuations were moment and density; these indexes were calculated by using a return-map. However these results were measured by an off-line system and were calculated after the experiment. So, an on-line (real-time) system was needed in order to construct a driver's internal state monitoring system. As a first step, an online system for estimating the human internal state was developed. This system is available for estimating the human internal state every 30 seconds.

A series of side impact tests have been conducted to evaluate the biofidelity of the latest prototype of a small side impact dummy, SID-II s β+(plus). The tests were lateral impacts for the thorax, shoulder, and pelvis, as well as lateral drops for the head, thorax, abdomen, and pelvis. The test data were compared to the response target corridors that were estimated by scaling the cadaver test data to a smaller occupant. The test results show that the head, should, thorax, abdomen and pelvis of the SID-II s β+ either completely or close to meets the response target corridors, and that its biofidelity has been improved from the previous dummy SID II s B-prototype.

Naturalistic driving data has been accumulated by driving data recorders to understand factors that contribute to collisions. Among the rear end conflicts at signalized intersections in the data, conflict data between the following vehicles and suddenly stopping lead vehicles were frequently observed just after their start. To investigate the following drivers' behavior in a realistic driving situation without collision danger, an instrumented vehicle equipped with a liquid-crystal display ahead of the windshield was developed, and an experiment reproducing such conflict on the display was conducted. It was found that a lead vehicle's rapid start (2.8 m/s₂ on average) before quitting its right turn caused the following vehicle's brake reaction time to be longer than a slow start (0.8 m/s₂ on average) did. This result suggests that a following driver's premature decision to start rapidly increases the risk of rear end collisions.

The New Car Assessment Program in Japan (JNCAP) was launched in 1995 in order to improve car safety performance. According to this program, installation conditions of safety devices and the results for braking performance and full- frontal crash tests are published every year. Introduction of JNCAP significantly increases the installation rate of safety devices and contributes much in enhancement of safety as seen in the decrease in the average injury severity of drivers and passengers. Side impact and offset frontal crash tests were introduced in 1999 and 2000, respectively. At present, the overall crash safety rating is carried out based on the results of the full-frontal, offset frontal, and side impact tests.

This paper summarizes a future side impact test procedure based on the Japanese presentation at the recent IHRA Side Impact WG meeting. Under current Japanese regulations, the MDB specifications and test procedures were determined based on a market study more than ten years ago. Thus, they may not reflect current automobile characteristics, the actual accident situation, and crash test results. In this study (1) the vehicle types, velocity of striking and struck vehicles, body injury regions, causes of injuries, etc., are reviewed with reference to the latest Japanese side impact accident data. The occupant percentages for the non-struck-side, rear seat and for female occupants as well as the injury levels were analyzed. (2) To determine the MDB specifications, based on data from passenger car models registered in 1998, the curb mass, geometry and stiffness were examined. (3) For factorial analysis, side impact tests were performed as for real accidents.

An investigation based on human visual search functions was conducted into the causative factors of traffic accidents at clear intersections in rural areas. The results indicated that it is difficult for drivers to detect a vehicle traveling on a collision course because the vehicle remains in the same position in the driver's visual field. Two systems are introduced to assist drivers' visual searches. One system uses an image processing technique, and the other utilizes DGPS and IVC techniques. This paper presents the development of the assistance system.

In order to review improvement of the recycling rate for an end-of-life vehicle, we implemented a life cycle assessment on the three treatment scenarios for automobile shredder residue (ASR): (A) Direct landfill of whole ASR, (B) Landfill after volume reduction and solidification, (C) Landfill of dry-distillation residue after energy recovery. As a result, we confirmed that case C was effective in achieving the numerical targets of the JAMA voluntary action plan for 2002.

Seat belts for rear passengers are not commonly used, even though they can significantly reduce fatalities. A passenger seat belt reminder (PSBR) is installed in order to encourage seat belt use, but the effectiveness of PSBRs on the rear seat passenger has not yet been proven. We have developed a methodology to assess PSBR effectiveness. There are two pathways to encourage seat belt use. The first is that PSBR directly facilitates the passenger's use. The second is to motivate the driver request passengers to use seat belts. In the experiment, we asked participants sitting in the driver's seat to select one of five ranks of likelihood to encourage the passenger when a PSBR was presented. We also asked participants sitting in the rear passenger seat to select the rank of likelihood to use the belt voluntarily with PSBR and that to use the belt when the driver requested. The degree of likelihood was quantified by averaging the assigned percentage values to the ranks.

Controllability (C) is the parameter that determines the Automotive Safety Integrity Level (ASIL) of each hazardous event based on an international standard of electrical and/or electronic systems within road vehicles (ISO 26262). C is classified qualitatively in ISO 26262. However, no specific method for classifying C is described. It is useful for C classification to define a specific classification based on objective data. This study assumed that C was classified using the percentage of drivers who could reduce Severity (S) in one or more classes compared with the S class in which the driver did not react to a hazardous event. An experiment simulated a situation with increased risk of collision with a leading vehicle due to insufficient brake force because of brake-assist failure when the experiment vehicle decelerated from 50 km/h on a straight road.

Effects of hands-free phone conversations on drivers' visual behavior and detection performance were examined using a gaze-tracking device and fixed-based driving simulator. The participants engaged in various conversation tasks (simple/arithmetic/unconstrained) while following a lead vehicle. The results indicated that hands-free-phone conversations, even if the contents are not subjectively demanding, can affect a driver's visual behavior. The increment of binocular gaze dissociation induced by conversing on a phone indicates that a driver's attention is diverted from the external scenery to the conversation. Furthermore, this observed dissociation of binocular gaze may represent a resting position, which is revealed only when binocular fusion is disrupted by occluding one eye.

Researchers concerned with motorcycle occupant protection have attempted to develop ways to protect the motorcycle occupant from injury. In the hope of finding a means to protect the motorcycle occupant's lower extremities, the authors have investigated past research, designed a device that incorporates an energy-absorbing component, tested the device in a series of collisions with automobiles, and performed an analysis of the test results to assess the merits of the new device. Results show that although the device may under certain circumstances reduce lower leg injuries, there may be increased potential for upper leg, chest, and head injuries

In this paper, an intersection collision warning system using DGPS (Differential Global Positioning System) will be proposed. The system is developed to prevent collisions of vehicles crossing at intersections, especially at well visibility intersections without traffic lights. Two GPS receivers are installed on two vehicles on the move towards the same intersection from different directions. The position and velocity information of the vehicles are measured by on-board GPS receivers, and then transmitted from one vehicle to another by inter-vehicle communication (IVC). Therefore, the relative position and direction of each vehicle and collision judgment coefficient (CJC) which is defined by using the relative position of vehicles are calculated. After taking the crossing position of directions and the variation of CJC into account, the position of the intersection and the possibility of collision can be predicted in advance. Warning will be given to drivers with a prearranged timing.

JAMA (Japan Automobile Manufactures Association, Inc.)'s guideline for car navigation systems is being decided on displayed the amount of information while driving. The position of a display and the estimated equation, which could be applied from a passenger car to a heavy truck, was studied. The evaluation index was the distance which drivers could become aware of a preceding vehicle by their peripheral vision, because car accidents while drivers glance at an in- vehicle display are almost the rear end collisions. As the results, the lower limit of a position of an in-vehicle display for a passenger car was 30 degrees, and a heavy truck was 46 degrees.

Sled tests were conducted with some seats which had different characteristics to understand the relationships between occupant motion and seat characteristics in lowspeed rear impacts. The position of the head restraint and the stiffness distribution of the seatback were selected as parameters expressing seat characteristics. Volunteer’s cervical vertebral motions were photographed with an x-ray cineradiographic system at a speed of 90 frames/sec as well as the visible motions of dummy’s and volunteer’s were recorded. The results indicated the head restraint position and upper seatback stiffness influenced occupant motions. Correlations between visible motions, such as ramping-up, retraction and extension, were also analyzed and some correlations were found.

ISO 26262 (Road vehicles - Functional safety), a functional safety standard for motor vehicles, was published in November 2011. In this standard, hazardous events associated with each item constituting a safety-related system are assessed according to three criteria, namely, Severity, Exposure, and Controllability, thereby determining ASILs (Automotive Safety Integrity Levels) representing safety levels for motor vehicles. Although motorcycles are not included in the scope of application of the current edition of ISO 26262, it is expected that motorcycles will be included in the next revision. However, it is not appropriate to directly apply ASILs to motorcycles. In the first place, the situation of usage in practice presumably differs between motorcycles and motor vehicles. Accordingly, in this research, we attempted to newly define Motorcycle Safety Integrity Levels (MSILs).

This study proposes a method for presenting maneuver request information of accelerator pedal to a driver via the accelerator pedal itself. By applying periodic force like vibration on an accelerator pedal, information is transferred to the driver without displacing the accelerator pedal. In this study, the authors focus on a saw-tooth wave as the periodic force. When the saw-tooth-waved force is applied on the accelerator pedal, a human driver feels as if the accelerator pedal is knocked by someone periodically. In addition, information about the quantity of requested maneuver can be transferred by the amplitude of the saw-tooth wave. Based on these facts, the saw-tooth wave is modified and optimized empirically with ten human drivers so that the information of direction is transferred most reliably. In addition, the relationship between the amplitude of the saw-tooth wave and requested quantity of the pedal maneuver that the drivers feel is formulated.

It is becoming more and more necessary to achieve a sustainable low-carbon society by mobility not depending on oil. Electric vehicles are appropriate for such a society, but expensive battery cost and long charging time prohibit the promotion of EVs. One of the solutions is minimizing battery usage by ultra-low fuel efficiency, so we developed an ultrahigh-efficient electric commuter concept car “C-ta”, which requires as small a battery as possible. We assumed that drivers would use the car as a second car for short-distance daily use, such as commuting, shopping, transportation of family, etc. In order to improve fuel efficiency, we mainly considered an ultra-light weight body and chassis, to which CFRP (carbon fiber reinforced plastic) greatly contributes, ultra-low rolling resistance tires, and highly accurate vehicle control technology with four in-wheel motors.