Search Results

This study computationally investigates the combined effects of EGR and boost pressure on HCCI autoignition using iso-octane, PRF50 and n-heptane. The computations were conducted using the single-zone model of CHEMKIN included in CHEMKIN-PRO with detailed chemical-kinetics mechanisms for iso-octane, PRF and n-heptane from Lawrence Livermore National Laboratory (LLNL). To better reproduce the state of EGR addition in real engine, the EGR composition is determined after several combustion cycles under the constant amount of fuel. All data points were acquired with a CA50 of 5°CA aTDC by adjusting initial temperature to remove the effect of combustion phasing, which can influence on HCCI autoignition from any effect of the EGR and boost pressure themselves. The results show that EGR increases the burn duration and reduces the maximum pressure-rise rate with lower peak of maximum heat-release rates for all fuels even for a boost pressure, which accelerates a HCCI autoignition propensity.

Prediction of the discharge path behavior between electrodes on a spark plug is important for efficient energy use in internal combustion engines, especially in lean combustion. In this paper, we propose a numerical model for the prediction of the spark path behaviors based on the coupling of a flow field, a Lagrangian particle model, and an equivalent circuit model. A turbulent flow around cylinders imitating electrodes is solved using a direct numerical simulation, in which Lagrangian particles along the spark path are tracked. Electric current and inter-electrode voltage are computed based on the energy conversion rate from the circuit to the mixture gas. As a result, a discharge path is reproduced with Lagrangian tracking particles virtually aligned between the cylinders. The spark path has a complicated structure along the spanwise direction due to the complex three-dimensional vortical structure of the cylinder wake.

A significant drawback to HCCI engines is the knocking caused by rapid increases in pressure. Such knocking limits the capacity for high-load operation. To solve this problem, thermal stratification in the combustion chamber has been suggested as possible solution. Thermal stratification has the potential to reduce the maximum value of the rate of pressure increase combustion by affecting the local combustion start time and extending the duration of combustion. The purpose of this study was to experimentally obtain fundamental knowledge about the effect of thermal stratification on the HCCI combustion process. Experiments were conducted in a rapid compression machine (RCM) equipped with a quartz window to provide optical access to the combustion chamber. The machine was fueled with DME, n-Butane, n-Heptane and iso-Octane, all of which are currently being investigated as alternative fuels and have different low temperature characteristics.

This paper experimentally and analytically evaluates the heat rejection/retention performance of a reversible thermal panel (RTP) which can autonomously change thermal performance depending on its own thermal conditions. The RTP is considered as a candidate methodology for thermal control of Venus mission, PLANET-C, in order to save survival heater power. An RTP prototype was tested and evaluated. An analytical thermal model of the RTP was also developed, and basic performances of the RTP were evaluated. Thermal performance of the RTP when applied to the longwave camera (LIR) of the PLANET-C was evaluated with an analytical thermal model as functions of fin deployment directions and rear surface properties of the RTP's fin. The analytical results showed that the RTP can save heater power in comparison to a conventional radiator.

The Homogeneous Charge Compression Ignition (HCCI) engine is possible to achieve high thermal efficiency and low emissions. One of the main challenges with HCCI engines is structuring the systems to control combustion phasing, crank angle of 50% heat release (CA50), for keeping high thermal efficiency and avoiding an excessive rate of pressure rise which causes knocking, when operating conditions vary. Though some HCCI combustion control systems, for example Variable Valve Timing System and Variable Compression Ratio System, have been suggested, these control systems are complex and heavy. In this study, for the development of a lightweight and small-sized generator HCCI engine fuelled with Dimethyl Ether (DME) which is low-emission and easy to autoignite, a simple HCCI combustion control system is suggested, and the control system is evaluated experimentally.

The purpose of this study was to gain a better understanding of the effects of in-cylinder gas temperature stratification on reducing the pressure-rise rate in HCCI combustion. HCCI combustion was investigated using an optically accessible engine and direct visualization of the combustion chemiluminescence. The engine was fueled with Di-Methyl Ether. Computational work was conducted on the gas compression and expansion strokes in HCCI engine with simple 0-dimensinal multi-zones model. When fuel inhomogeneous charging in experiment, maximum heat release rate decreased. Combustion duration got longer. Maximum pressure-rise rate decreased. Chemiluminescence, of which transition was identified from the side of intake valve to the side of exhaust valve, was observed. It is need for total moderate heat release to get local moderate combustion with not overall but continuous combustion in chamber.

Theoretically, homogeneous charge compression engines (HCCI) are able to grant a high thermal efficiency, as well as a low NOx and particulate emissions. This ability is mainly due to the combustion process, which, contrary to both Diesel and Gasoline engine, is homogeneous in time and space within the combustion chamber. But despite these advantages, the engine operating condition is limited by the narrow boundaries of misfire at low load and knocking at high load. For that matter, one of the numerous ways of overcoming knocking is to deliberately create fuel inhomogeneities within the combustion chamber, since it has proved to lengthen combustion duration and to drastically reduce maximum pressure rise rate (PRR). Nevertheless, though the global effects of fuel inhomogeneities on PRR have been studied, we lack information that explains this phenomenon.

In this study, the effects of fuel properties, aromatics content and 90% distillation temperature T90, on flame temperature and soot formation were studied using a rapid compression machine (RCM). Aromatics content and T90 distillation temperature were parameters isolated from influence of each other, and from cetane number. A fuel spray was injected in the RCM combustion chamber by a single nozzle hole. The ignition and combustion processes of diesel spray were observed by a high-speed direct photography. Flame temperature and KL factor (which indicates the soot concentration), were analyzed by the two-color method. The rate of heat release was analyzed from indicated diagrams. The fuels with aromatics content showed higher flame temperature. The fuel with highest T90 distillation temperature showed highest flame temperature.

In this study, effects of nozzle hole diameter and EGR ratio on flame temperature (indication of NO formation) and KL value (indication of soot formation) were investigated. Combustion of a single diesel fuel spray in the cylinder of a rapid compression machine (RCM) was analyzed. Three nozzles with different hole diameter were used corresponding to present, near term and long term heavy duty diesel engine specifications. EGR was simulated through 2%vol. CO2 addition to the inlet air and by increase of in-cylinder surrounding gas temperature. Various types of fuels were used in this. The ignition and combustion processes of diesel fuel spray were observed by a high-speed direct photography and by indicated pressure diagrams. Flame temperature and KL factor were analyzed by a two-color method. With larger nozzle hole diameters there are larger high temperature areas. With smaller nozzle hole diameters there is more soot formed. Introduction of 2% vol.

This paper describes a new passive thermal control device-a Reversible Thermal Panel (RTP)-which changes its function reversibly from a radiator to a solar absorber by deploying/stowing the radiator/absorber reversible fin. The RTP consists of Highly Oriented Graphite Sheets (HOGSs), which have characteristics of high thermal conductivity, flexibility and light weight, as thermal transport units, which can transport the heat from equipment to reversible fin, and of a Shape - Memory Alloy (SMA) as a passively rotary actuator to deploy/stow the reversible fin. The RTP prototype model was designed and fabricated using HOGSs, a honeycomb base palate, and a prototype reversible rotary actuator. The heat rejection performance of the RTP as a radiator and the heat absorption performance as an absorber were evaluated by thermal vacuum tests and thermal analyses. The autonomous thermal controllability achieved using the prototype rotary actuator was also evaluated.

In the HCCI Engine, inhomogeneity in fuel distribution and temperature in the pre-mixture exists microscopically, and has the possibility of affecting the ignition and combustion process. In this study, the effect of charge inhomogeneity in fuel distribution on the HCCI combustion process was investigated. Two-dimensional images of the chemiluminescence were captured by using a framing camera with an optically accessible engine in order to understand the spatial distribution of the combustion. DME was used as a test fuel. By changing a device for mixing air and fuel in the intake manifold, inhomogeneity in fuel distribution in the pre-mixture was varied. The result shows that luminescence is observed in a very short time in a large part of the combustion chamber under the homogeneous condition, while luminescence appears locally with considerable time differences under the inhomogeneous condition.

The purpose of this research is to get fundamental knowledge and to experimentally understand about combustion characteristics of the fuel mixture. This paper shows the Homogeneous Charge Compression Ignition (HCCI) characteristics of a mixture of n-Heptane and iso-Octane in a rapid compression machine. The experimental matrixes cover the n-Heptane mixing ratios, rn-Heptane, ranging from 0 to 100vol% and the equivalence ratios ranging from 0.1 to 0.6. The experimental study on the effect of mixing fuels focuses on the low temperature oxidation reaction temperatures, TL, the high temperature oxidation reaction temperatures, TH, the low temperature oxidation reaction starting times, tL, the high temperature oxidation reaction starting times, tH, and the degeneration period. The results show that as rn-Heptane decreases, tL and tH become longer and TL and TH increase by 30K. As the equivalence ratio increases, tL becomes longer but tH is not a function of equivalence ratio.

Variable emittance radiator, called SRD, is a thin and light ceramic tile whose infrared emissivity is varied proportionally by its own temperature. Bonded only to the external surface of spacecrafts, it controls the heat radiated to deep space without electrical or mechanical parts such as the thermal louver. By applying this new device for thermal control of spacecrafts, considerable weight and cost reductions can be achieved easily. In this paper, the new design and the new manufacturing process of the SRD and its optical properties, such as the total hemispherical emittance and the solar absorptance, are described. By introducing this new design and manufacturing process, the weight of the SRD is easily decreased, keeping its strength and the optical properties.

Knock is a factor hindering enhancement of the thermal efficiency of spark ignition engines, and is an unsteady phenomenon that does not necessarily occur each cycle. In addition, the heat release history of the flame also fluctuates from cycle to cycle, and the auto-ignition process of the unburned mixture (end-gas), compressed by the global increase in pressure due to release of chemical energy, is affected by this fluctuation. Regarding auto-ignition of the end-gas, which can be the origin of knock, this study focused on the fluctuation of the flame heat release pattern, and used a zero-dimensional (0D) detailed chemical reaction calculation in an attempt to analyze and examine the consequence on the end-gas compression and auto-ignition process of changes in the i) start of combustion, ii) combustion duration and iii) center of heat release of the flame.

The HCCI combustion mode poses its own set of narrow engine operating by knocking. In order to solve this, inhomogeneity method of mixture and temperature is suggested. The purpose of this research is to get fundamental knowledge about the effect of thermal stratification on HCCI combustion of n-Heptane/iso-Octane-Air mixture. The temperature stratification is made by buoyancy effect in combustion chamber of RCM. The analysis items are pressure, temperature of in-cylinder gas and combustion duration. In addition, the structure of flames using the two dimensional chemiluminescence's images by a framing camera are analyzed. Under stratification, the LTR starting time and the HTR starting time are advanced than that of homogeneous. Further, the LTR period of homogeneous conditions became shorter than that of the stratified conditions. . With the case of homogeneous condition, the luminosity duration becomes shorter than the case of stratified condition.

CNG/diesel dual-fuel engine is using CNG as a main fuel, and injects diesel only a little as an ignition priming. In this study, remodeling an existing diesel engine into dual-fuel engine that can inject diesel with high pressure by CRDI (Common Rail Direct Injection), and injecting CNG at intake port for premixing. The results show that CNG/diesel dual-fuel engine satisfied coordinate torque and power with conventional diesel engine. And CNG alternation rate is over 89% in all operating ranges of CNG/diesel dual-fuel engine. PM emission is lower 94% than diesel engine, but NOx emission is higher than diesel engine. The output of dual fuel mode is 95% by the diesel mode. At this time, amount of CO₂ and PM are decreased while CO, NOx, and THC are increased. In NEDC mode, exhaust gases except NOx are decreased.

A lightweight 100 W-class deployable radiator with environment-adaptive functions has been investigated. This radiator - Reversible Thermal Panel (RTP) - is composed of flexible high thermal conductive materials and a passive reversible actuator, and it changes its function from a radiator to a solar absorber by deploying/stowing the reversible fin upon changes in the heat dissipation and thermal environment. The RTP is considered one of the candidates of thermal control methodology for the Japanese Venus mission “Planet-C”, which will be launched in 2010 to save its survival heater power. In this paper, design and fabrication of the RTP proto-model (PM) and the test results of deployment/stowing characteristics in an atmospheric condition are reported. Thermal performance estimation with thermal analytical model of the RTP PM is also presented.

In the HCCI (Homogeneous Charge Compression Ignition) engine, a mixture of fuel and air is supplied to the cylinder and auto-ignition occurs resulting from compression. This method can expand the lean flammability limit, realizing smokeless combustion and also having the potential for realizing low NOx and high efficiency. The optimal ignition timing is necessary in order to keep high thermal efficiency. The Ignition in the HCCI engine largely depends on the chemical reaction between the fuel and the oxidizer. Physical methods in conventional engines cannot control it, so a chemical method is demanded. Combustion duration is maintained properly to avoid knocking. In addition, the amount of HC and CO emissions must be reduced. The objective of this study is to clarify the following through calculations with detailed chemical reactions and through experiment with the 2-stroke HCCI engine: the chemical reaction mechanism, and HC and CO emission mechanisms.

The research shows the experimental results for a free piston linear engine according to operation conditions of the linear engine and the structure of linear generator for generating electric power. The powerpack used in this paper consists of the two-stroke free piston linear engine, linear generators and air compressors. Each parameter of fuel input heat, equivalence ratio, spark timing delay, electrical resistance and air gap length were set up to identify the combustion characteristics and to examine the performance of linear engine. The linear engine was fueled with propane. In the course of all linear engine operations, intake air was inputted under the wide open throttle state. Air and fuel mass flow rate were varied by using mass flow controller and these were premixed by pre-mixing device. Subsequently, pre-mixture was directly supplied into each cylinder.

This work has been investigated the potential of in-cylinder EGR stratification for reducing the pressure rise rate of DME HCCI engines, and the coupling of both thermal stratification and fuel stratification. The numerical analyses were done by using five-zone version of CHEMKIN-II kinetics rate code, and kinetic mechanics for DME. The effects of inert components were used for the presence of EGR in calculation. Three cases of EGR stratification were tested on both thermal stratification and fuel stratification at the fixed initial temperature, pressure and fueling rate at BDC. In order to explore the appropriate stratification of EGR, EGR width was employed from zero to thirty percent. Firstly, EGR homogeneity case which means EGR width zero was examined. Secondly, EGR is located densely in hotter zone for combining with thermal stratification or in richer zone for a combination with fuel stratification. Lastly, the case was judged inversely with the second case.