Refine Your Search

Topic

Author

Search Results

Technical Paper

The Application of Ceramic and Catalytic Coatings to Reduce the Unburned Hydrocarbon Emissions from a Homogeneous Charge Compression Ignition Engine

2000-06-19
2000-01-1833
An experimental and theoretical study of the effect of thermal barriers and catalytic coatings in a Homogeneous Charge Compression Ignition (HCCI) engine has been conducted. The main intent of the study was to investigate if a thermal barrier or catalytic coating of the wall would support the oxidation of the near-wall unburned hydrocarbons. In addition, the effect of these coatings on thermal efficiency due to changed heat transfer characteristics was investigated. The experimental setup was based on a partially coated combustion chamber. The upper part of the cylinder liner, the piston top including the top land, the valves and the cylinder head were all coated. As a thermal barrier, a coating based on plasma-sprayed Al2O3 was used. The catalytic coating was based on plasma-sprayed ZrO2 doped with Platinum. The two coatings tested were of varying thickness' of 0.15, 0.25 and 0.6 mm. The compression ratio was set to 16.75:1.
Technical Paper

Supercharged Homogeneous Charge Compression Ignition (HCCI) with Exhaust Gas Recirculation and Pilot Fuel

2000-06-19
2000-01-1835
In an attempt to extend the upper load limit for Homogeneous Charge Compression Ignition (HCCI), supercharging in combination with Exhaust Gas Recirculation (EGR) have been applied. Two different boost pressures were used, 1.1 bar and 1.5 bar. High EGR rates were used in order to reduce the combustion rate. The highest obtained IMEP was 16 bar. This was achieved with the higher boost pressure, at close to stoichiometric conditions and with approximately 50 % EGR. Natural gas was used as the main fuel. In the case with the higher boost pressure, iso-octane was used as pilot fuel, to improve the ignition properties of the mixture. This made it possible to use a lower compression ratio and thereby reducing the maximum cylinder pressure. The tests were performed on a single cylinder engine operated at low speed (1000 rpm). The test engine was equipped with a modified cylinder head, having a Variable Compression Ratio (VCR) mechanism.
Technical Paper

A Study of the Homogeneous Charge Compression Ignition Combustion Process by Chemiluminescence Imaging

1999-10-25
1999-01-3680
An experimental study of the Homogeneous Charge Compression Ignition (HCCI) combustion process has been conducted by using chemiluminescence imaging. The major intent was to characterize the flame structure and its transient behavior. To achieve this, time resolved images of the naturally emitted light were taken. Emitted light was studied by recording its spectral content and applying different filters to isolate species like OH and CH. Imaging was enabled by a truck-sized engine modified for optical access. An intensified digital camera was used for the imaging. Some imaging was done using a streak-camera, capable of taking eight arbitrarily spaced pictures during a single cycle, thus visualizing the progress of the combustion process. All imaging was done with similar operating conditions and a mixture of n-heptane and iso-octane was used as fuel. Some 20 crank angles before Top Dead Center (TDC), cool flames were found to exist.
Technical Paper

Optical Diagnostics Applied to a Naturally Aspirated Homogeneous Charge Compression Ignition Engine

1999-10-25
1999-01-3649
Basic optical properties have been investigated in order to characterize the HCCI-combustion process. Basic optical properties of a Homogeneous Charge Compression Ignition (HCCI) engine have been investigated in order to characterize the combustion process. The absorption of light propagating through the combustion chamber has been spectrally resolved for four different fuels. Significant differences between the fuels could be detected. Complementary information could be obtained by recording spontaneous emission of radiation during combustion. Raman point measurements were used to quantify cycle-to-cycle variations of the equivalence ratio. The homogeneity of the charge was monitored by the use of two-dimensional tracer LIF. That method was also utilized to investigate the flame development. The experiments were performed in a six-cylinder, truck-sized engine with one cylinder modified to allow for optical access.
Technical Paper

A Simple Approach to Studying the Relation between Fuel Rate Heat Release Rate and NO Formation in Diesel Engines

1999-10-25
1999-01-3548
Modern diesel engine injection systems are largely computer controlled. This opens the door for tailoring the fuel rate. Rate shaping in combination with increased injection pressure and nozzle design will play an important role in the efforts to maintain the superiority of the diesel engine in terms of fuel economy while meeting future demands on emissions. This approach to studying the potential of rate shaping in order to reduce NO formation is based on three sub-models. The first model calculates the fuel rate by using standard expressions for calculating the areas of the dimensioning flow paths in the nozzle and the corresponding discharge coefficients. In the second sub-model the heat release rate is described as a function of available fuel energy, i.e. fuel mass, in the cylinder. The third submodel is the multizone combustion model that calculates NO for a given heat release rate under assumed air /fuel ratios.
Technical Paper

Cylinder to Cylinder and Cycle to Cycle Variations in a Six Cylinder Lean Burn Natural Gas Engine

2000-06-19
2000-01-1941
The cylinder to cylinder and cycle to cycle variations were measured in a production type Volvo natural gas engine. Cylinder pressure was measured in all six cylinders. Emission measurements were performed individually after all cylinders, and commonly after the turbocharger. Measurements (ECE R49 13-mode) were performed with different spark gap and two different locations for fuel injection, one before the throttle and one before the turbocharger. Heat-release and lambda calculations show substantial cylinder to cylinder variations, due to lambda variations between the cylinders. The slow burn combustion chamber, with low turbulence, results in high cycle to cycle variations (> 100% COV imep) for some of the load cases.
Technical Paper

Fuel Distribution in an Air Assist Direct Injected Spark Ignition Engine with Central Injection and Spark Plug Measured with Laser Induced Fluorescence

2000-06-19
2000-01-1898
The fuel distribution in an air assist direct injection engine was measured with Planar Laser Induced Fluorescence, PLIF. The engine was fueled with isooctane and 3-pentanon was used as the fuel tracer. The optical engine was of the prolonged piston type, with a quartz ring in the upper part of the cylinder. Both the fuel injector and the spark plug were centrally located in the cylinder head. Two different pistons were examined: flat piston and bowl in piston. Results show that the differences in fuel stratification are very large for the flat piston compared to the piston with a bowl.
Technical Paper

Prediction of Heat Transfer to the Walls for Autoignition Related Situations in SI Engines

2000-03-06
2000-01-1084
A theoretical investigation is presented concerning how the heat transfer process from the gas in the combustion chamber, burned as well as the unburned gas regions, to the walls is affected by the autoignition phenomenon in SI engines. The zonal model in ref. [1] is adapted for the calculations. The radiative heat flux during the heat release period and the heat transfer in the thermal boundary layer by convection are predicted for situations when autoignition has occurred. The cylinder wall temperature is also used as a parameter in this study. The effects of engine operating parameters such as engine speed, timing of ignition, duration time of flame propagation and the fuel parameter Research Octane Number, i.e., RON, on the heat flux to the walls have been studied. The heat release is calculated for a detailed chemical kinetic model, refs. [1, 2 and 3].
Technical Paper

Effect of Inhomogeneities in the End Gas Temperature Field on the Autoignition in SI Engines

2000-03-06
2000-01-0954
This paper reports an one–dimensional modeling procedure of the hot spot autoignition with a detailed chemistry and multi–species transport in the end gas in an SI engine. The governing equations for continuity of mass, momentum, energy and species for an one–dimensional, unsteady, compressible, laminar, reacting flow and thermal fields are discretized and solved by a fully implicit method. A chemical kinetic mechanism is used for the primary reference fuels n–heptane and iso–octane. This mechanism contains 510 chemical reactions and 75 species. The change of the cylinder pressure is calculated from both flame propagation and piston movement. The turbulent velocity of the propagating flame is modeled by the Wiebe function. Adiabatic conditions, calculated by minimizing Gibb's free energy at each time step, are assumed behind the flame front in the burned gas.
Technical Paper

Laser-Rayleigh Imaging of DME Sprays in an Optically Accessible DI Diesel Truck Engine

2001-03-05
2001-01-0915
Laser-Rayleigh imaging has been employed to measure the relative fuel concentration in the gaseous jet region of DME sprays. The measurements were performed in an optically accessible diesel truck engine equipped with a common rail injection system. A one-hole nozzle was used to guarantee that the recorded pressure history was associated with the heat release in the imaged spray. To compensate for the low compression ratio in the modified engine the inlet air was preheated. Spray development was studied for two levels of preheating, from the start of injection to the point where all fuel was consumed. The results indicate that there is a strong correlation between the amount of unburned fuel present in the cylinder and the rate of heat release at a given time. The combustion can not be described as purely premixed or purely mixing-controlled at any time, but always has an element of both. After all fuel appears to have vanished there is still an extended period of heat release.
Technical Paper

The Effect of Knock on the Heat Transfer in an SI Engine: Thermal Boundary Layer Investigation using CARS Temperature Measurements and Heat Flux Measurements

2000-10-16
2000-01-2831
It is generally accepted that knocking combustion influences the heat transfer in SI engines. However, the effects of heat transfer on the onset of knock is still not clear due to lack of experimental data of the thermal boundary layer close to the combustion chamber wall. This paper presents measurements of the temperature in the thermal boundary layer under knocking and non-knocking conditions. The temperature was measured using dual-broadband rotational Coherent anti-Stokes Raman Spectroscopy (CARS). Simultaneous time-resolved measurements of the cylinder pressure, at three different locations, and the heat flux to the wall were carried out. Optical access to the region near the combustion chamber wall was achieved by using a horseshoe-shaped combustion chamber with windows installed in the rectangular part of the chamber. This arrangement made CARS temperature measurements close to the wall possible and results are presented in the range 0.1-5 mm from the wall.
Technical Paper

Load Control Using Late Intake Valve Closing in a Cross Flow Cylinder Head

2001-09-24
2001-01-3554
A newly developed cross flow cylinder head has been used for comparison between throttled and unthrottled operation using late intake valve closing. Pressure measurements have been used for calculations of indicated load and heat-release. Emission measurements has also been made. A model was used for estimating the amount of residual gases resulting from the different load strategies. Unthrottled operation using late intake valve closing resulted in lower pumping losses, but also in increased amounts of residual gases, using this cylinder head. This is due to the special design, with one intake valve and one exhaust valve per camshaft. Late intake valve closing was achieved by phasing one of the camshafts, resulting in late exhaust valve closing as well. With very late phasing - i.e. low load - the effective compression ratio was reduced. This, in combination with high amount of residual gases, resulted in a very unstable combustion.
Technical Paper

Experimental Investigations of Flow and Temperature Fields in an SI Engine and Comparison with Numerical Analysis

1999-10-25
1999-01-3541
Two-dimensional cycle-resolved burnt gas temperatures were measured using two line atomic fluorescence (TLAF) in a single cylinder spark ignition car engine. Mapping of the in-cylinder flow was done under the same operating conditions using Particle Imaging Velocimetry (PIV). Experimental data for temperature and flow was compared to results from numerical simulations.
Technical Paper

Investigation of the Fuel Distribution and the In-cylinder Flow Field in a Stratified Charge Engine Using Laser Techniques and Comparison with CFD-Modelling

1999-10-25
1999-01-3540
This paper presents an investigation of a Volvo Direct Injection Spark Ignition (DISI) engine, where the fuel distribution and the in-cylinder flow field have been mapped by the use of laser techniques in an engine with optical access. Along with the experimental work, CFD-modelling of flow and fuel distribution has been performed. Laser Induced Fluorescence (LIF) visualisation of the fuel distribution in a DI-engine has been performed using an endoscopic detection system. Due to the complex piston crown geometry it was not possible to monitor the critical area around the sparkplug with conventional, through the piston, detection. Therefore, an endoscope inserted in the spark plug hole was used. This approach gave an unrestricted view over the desired area. In addition, the in-cylinder flow fields have been monitored by Particle Image Velocimetry (PIV) through cylinder and piston. The results from both the LIF and the PIV measurements have been compared with CFD-modelling at Volvo.
Technical Paper

Local Air-Fuel Ratio Measurements Using the Spark Plug as an Ionization Sensor

1997-02-24
970856
The influence of variable air-fuel ratio inside a spark ignition engine is examined by the use of an ionization sensor. The measured ion currents are used for predicting the local air-fuel ratio in the vicinity of the spark plug. In order to support the results, a theoretical analysis has been made. An instationary chemical kinetic model burning a mixture of iso-octane and n-heptane is used for the calculations. The results are used to reconstruct the crank angle resolved ion current that has been measured in an engine. This technique has been developed in order to offer a supplementary low-cost facility of controlling the air-fuel ratio within the combustion chamber of an engine.
Technical Paper

Knock in Spark-Ignition Engines: End-Gas Temperature Measurements Using Rotational CARS and Detailed Kinetic Calculations of the Autoignition Process

1997-05-01
971669
Cycle-resolved end-gas temperatures were measured using dual-broadband rotational CARS in a single-cylinder spark-ignition engine. Simultaneous cylinder pressure measurements were used as an indicator for knock and as input data to numerical calculations. The chemical processes in the end-gas have been analysed with a detailed kinetic mechanism for mixtures of iso-octane and n-heptane at different Research Octane Numbers (RON'S). The end-gas is modelled as a homogeneous reactor that is compressed or expanded by the piston movement and the flame propagation in the cylinder. The calculated temperatures are in agreement with the temperatures evaluated from CARS measurements. It is found that calculations with different RON'S of the fuel lead to different levels of radical concentrations in the end-gas. The apperance of the first stage of the autoignition process is marginally influenced by the RON, while the ignition delay of the second stage is increased with increasing RON.
Technical Paper

Investigation of End-Gas Temperature and Pressure Increases in Gasoline Engines and Relevance for Knock Occurrence

1997-05-01
971671
A detailed analysis of the end-gas temperature and pressure in gasoline engines has been performed. This analysis leads to a simplified zero-dimensional model, that considers both, the compression and the expansion of the end-gas by the piston movement, and the compression by the flame front. If autoignition occurs in the end-gas the sudden rise of the pressure and the heat release is calculated. The rate form of the first law of thermodynamics for a control volume combined with the mass conservation equation for an unsteady and a uniform-flow process are applied. The heat of formation in the end-gas due to the chemical activity has been taken into account. In addition, a chemical kinetic model has been applied in order to study the occurrence of autoignition and prediction of knock.
Technical Paper

In-Cylinder Flow in High Speed Two-Stroke Engines with Different Transfer Channels

1997-02-24
970357
2-D LDV measurements were performed in the cylinder of a two-stroke engine. The transfer channels of the cylinders were of two different designs: Open transfer channels and “cup handle” transfer channels. The engine was run at its rated speed, 9000 rpm. Optical access to the cylinder was achieved by replacing the standard cylinder head with a quartz window. No addition of seeding was made, since the fuel droplets were not entirely vaporized as they entered the cylinder and thus served as seeding. Results show that the flow out from the cup handle transfer channels is more directed away from the exhaust port, which promotes loop scavenging. The RMS-value, “turbulence”, was low close to the transfer ports in both cylinders, but increased rapidly towards the middle of the cylinder.
Technical Paper

Combustion Chambers for Supercharged Natural Gas Engines

1997-02-24
970221
This work is a continuation of earlier research conducted on the effects of different combustion chambers on turbulence, combustion, emissions and efficiency for natural gas converted diesel bus engines. In this second measurement series the engine (Volvo TD102) was supercharged to enable bmep up to 18 bar at λ = 1.6-1.9. Six different combustion chambers were used. The results show that different geometrical combustion chambers, with the same compression ratio (12:1), have very different combustion performance. A high rate of heat release is favorable for lean operation, and the design of the combustion chamber is very important for the knock and misfire limits.
Technical Paper

Combustion Chambers for Natural Gas SI Engines Part I: Fluid Flow and Combustion

1995-02-01
950469
The most economical way to convert truck and bus DI-diesel engines to natural gas operation is to replace the injector with a spark plug and modify the combustion chamber in the piston crown for spark ignition operation. The modification of the piston crown should give a geometry well suited for spark ignition operation with the original swirling inlet port. Ten different geometries were tried on a converted VOLVO TD102 engine and a remarkably large difference in the rate of combustion was noted between the chambers. To find an explanation for this difference a cycle resolved measurement of the in-cylinder mean velocity and turbulence was performed with Laser Doppler Velocimetry (LDV). The results show a high correlation between in cylinder turbulence and rate of heat release in the main part of combustion.
X