Search Results

The present paper aims at discussing the flow/flame interaction in a lean burn spark ignition engine. The mean velocity and cycle resolved turbulence are measured with laser Doppler velocimetry. The cylinder pressure is recorded and a one-zone heat release calculation performed. The very early part of flame propagation is measured using two orthogonal Schlieren systems, each capturing one image of the progressing flame at a given time after spark onset. The two resulting 2D images are then, after preprocessing, used to reconstruct the three-dimensional flame. The volume of the true flame is estimated by simulating, using Markov Chain Monte Carlo techniques, a number of possible flames that are consistent with the projections on the images. The uncertainty of the estimated flame volume is given by the variation of the volume estimates. In the calculations, the volume of that part of the spark plug that is inside the flame is subtracted.

Wavelet analysis was used to calculate turbulence and mean velocity levels for LDV measurements made in a four valve spark ignition engine. Five different camshafts were tested, and they produce significantly different flow behaviour. The standard cam gives tumble and with valve deactivation, swirl is produced. One camshaft with early inlet valve closing and two camshafts with late inlet valve closing were also tested. The wavelet toolbox for Matlab version 5.1 has been used for the wavelet calculations. The wavelet technique produces both time resolved and frequency resolved velocity information. The results indicate some influence of the turbulence frequency content on the rate of heat release. Correlation against heat-release can be seen for different scales of turbulence. The breakdown of the tumble (low frequency turbulence) into high frequency turbulence can be seen clearly.

A naturally aspirated in-line six-cylinder 2.9-litre Volvo engine is operated in Homogeneous Charge Compression Ignition (HCCI) mode, using camshafts with low lift and short duration generating negative valve overlap. This implementation requires only minor modifications of the standard SI engine and allows SI operation outside the operating range of HCCI. Standard port fuel injection is used and pistons and cylinder head are unchanged from the automotive application. A heat exchanger is utilized to heat or cool the intake air, not as a means of combustion control but in order to simulate realistic variations in ambient temperature. The combustion is monitored in real time using cylinder pressure sensors. HCCI through negative valve overlap is recognized as one of the possible implementation strategies of HCCI closest to production. However, for a practical application the intake temperature will vary both geographically and from time to time.

The Homogeneous Charge Compression Ignition (HCCI) is the third alternative for combustion in the Internal Combustion (IC) engines. Here, a homogeneous charge is used as in a spark ignited engine but the charge is compressed to auto-ignition as in a diesel. The characteristics of HCCI were compared to SI using a 1.6 liter single cylinder engine with compression ratio 21:1 in HCCI mode and 12:1 in SI mode. Three different fuels were used; isooctane, ethanol and natural gas. Some remarkable results were noted in the experiments: The indicated efficiency of HCCI was much better than for SI operation. Very little NOx was generated with HCCI, eliminating the need for a LeanNOx catalyst. However, HCCI generated more HC and CO than SI operation. Stable and efficient operation with HCCI could be obtained with λ=3 to λ=9 using isooctane or ethanol. Natural gas, with a higher octane number, required a richer mixture to run in HCCI mode.

The main benefit of HCCI engines compared to SI engines is improved fuel economy. The drawback is the diluted combustion with a substantially smaller operating range if not some kind of supercharging is used. The reasons for the higher brake efficiency in HCCI engines can be summarized in lower pumping losses and higher thermodynamic efficiency, due to higher compression ratio and higher ratio of specific heats if air is used as dilution. In the low load operating range, where HCCI today is mainly used, other parameters as friction losses, and cooling losses have a large impact on the achieved brake efficiency. To initiate the auto ignition of the in-cylinder charge a certain temperature and pressure have to be reached for a specific fuel. In an engine with high in-cylinder cooling losses the initial charge temperature before compression has to be higher than on an engine with less heat transfer.

2D-LDV-measurements were made on the flow from one transfer channel into the cylinder in a small two-stroke SI engine. The LDV measuring volume was located just outside the transfer port. The engine was a carburetted piston-ported crankcase compression chainsaw engine and it was run with wide open throttle at 9000 RPM. The muffler was removed to enable access into the cylinder. No additional seeding was used; the fuel and/or oil was not entirely vaporized as it entered the cylinder. Very high velocities (-275 m/s) were detected in the beginning of the scavenging phase. The horizontal velocity was, during the whole scavenging phase, higher than the vertical.

2-D LDV measurements were performed on two different cylinder designs in a fired two-stroke engine running with wide-open throttle at 9000 rpm. The cylinders examined were one with open transfer channels and one with cup handle transfer channels. Optical access to the cylinder was achieved by removing the silencer and thereby gain optical access through the exhaust port. No addition of seeding was made, since the fuel droplets were not entirely vaporized as they entered the cylinder and thus served as seeding. Results show that the loop-scavenging effect was poor with open transfer channels, but clearly detectable with cup handle channels. The RMS-value, “turbulence”, was low close to the transfer ports in both cylinders, but increased rapidly in the middle of the cylinder. The seeding density was used to obtain information about the fuel concentration in the cylinder during scavenging.

The fuel distribution in an air assist direct injection engine was measured with Planar Laser Induced Fluorescence, PLIF. The engine was fueled with isooctane and 3-pentanon was used as the fuel tracer. The optical engine was of the prolonged piston type, with a quartz ring in the upper part of the cylinder. Both the fuel injector and the spark plug were centrally located in the cylinder head. Two different pistons were examined: flat piston and bowl in piston. Results show that the differences in fuel stratification are very large for the flat piston compared to the piston with a bowl.

The cylinder to cylinder and cycle to cycle variations were measured in a production type Volvo natural gas engine. Cylinder pressure was measured in all six cylinders. Emission measurements were performed individually after all cylinders, and commonly after the turbocharger. Measurements (ECE R49 13-mode) were performed with different spark gap and two different locations for fuel injection, one before the throttle and one before the turbocharger. Heat-release and lambda calculations show substantial cylinder to cylinder variations, due to lambda variations between the cylinders. The slow burn combustion chamber, with low turbulence, results in high cycle to cycle variations (> 100% COV imep) for some of the load cases.