Search Results

In order to achieve the required future CO2 reduction targets, significant further development of both gasoline and diesel engines is required. One of the main methods to achieve this with the gasoline engine in the short to medium term is through the application of engine downsizing, which has resulted in numerous downsized engines already being brought to production. It is, however, considered that there is still significant further CO2 reduction potential through continued development of this technology. This paper considers the future development of gasoline engine downsizing in the short to medium term and the various technologies that can be applied to further increase the efficiency of operation. As such this paper covers, among other areas, fundamental engine layout and design, alternative boosting systems, methods of increasing part load efficiency and vehicle modelling, and uses analysis tools and engine test results to show the benefits achievable.

This work was concerned with evaluation of the performance and emissions of potential future biofuels during advanced spark ignition engine operation. The fuels prepared included three variants of gasoline, three gasoline-ethanol blends and a gasoline-butanol fuel altogether covering a range of oxygen mass concentrations and octane numbers to identify key influencing parameters. The combustion of the fuels was evaluated in a turbocharged multi-cylinder direct fuel injection research engine equipped with a standard three-way catalyst and an external EGR circuit that allowed use of either cooled or non-cooled EGR. The engine operating effects studied at both part and boosted high load conditions included fuel injection timing and pressure, excess air tolerance, EGR tolerance and spark retard limits. A number of blends were also mapped at suitable sites across the European drive cycle under downsized engine conditions.

Since the agreement to reduce average new car CO2 emissions to 140g/km by 2008, fuel consumption improvement has been one of the main drivers for engine development within the automotive industry. Numerous technologies to reduce vehicle fuel consumption have been investigated, with gasoline engine downsizing being shown as one of the most promising technologies for immediate implementation. In order to achieve further fuel economy gains more aggressive levels of downsizing are being pursued, increasing the requirements for broader and higher pressure ratio compressor maps. The currently reported work shows the development of a fully variable compressor map enhancer, which has the ability to provide both positive and negative pre-whirl. The effect of the map enhancer is shown on both the surge and choke margin of the compressor map when tested on a turbocharged gasoline engine.

This paper introduces the new 3 cylinder 1.2l downsizing technology demonstrator engine from MAHLE. The purpose of the paper is to describe the design approach and technologies applied. Emphasis is given to the low speed torque and transient response issues associated with advanced downsized engines. An overview of the design of all engine systems is provided, including the predictive analysis results used to validate, guide and optimize the design process. The design targets outstanding levels of performance, fuel consumption & drivability.

This experimental work was concerned with the combination of internal EGR with an early inlet valve closure strategy for improved part-load fuel economy. The experiments were performed in a new spark-ignited thermodynamic single cylinder research engine, equipped with a mechanical fully variable valvetrain on both the inlet and exhaust. During unthrottled operation at constant engine speed and load, increasing the mass of trapped residual allowed increased valve duration and lift to be used. In turn, this enabled further small improvements in gas exchange efficiency, thermal efficiency and hence indicated fuel consumption. Such effects were quantified under both port and homogeneous central direct fuel injection conditions. Shrouding of the inlet ports as a potential method to increase in-cylinder gas velocities has also been considered.

Evolving emissions legislation and concerns for diminishing fuel reserves continue to prompt the automotive industry to seek improvements in engine operation. The application of advanced combustion and system-based concepts is being studied in detail. However, it is believed prudent to first consider the optimization of the friction of the engine, to allow a more cost effective CO2 and fuel consumption reduction policy. MAHLE has developed an optimised friction engine to demonstrate the potential fuel consumption gains available to engine manufacturers and designers. The baseline 2.0 litre turbocharged, direct injection gasoline engine was modified to suit the application of new friction optimized components. This included piston, ring pack, connecting rod, crankshaft bearings, lubrication system, valvetrain and cooling system. A discussion of the design changes, including analysis results, is made. Motored rig and fired engine test results are presented to show the individual gains.

Gasoline engine downsizing has become a popular and effective approach to reduce CO2 emissions from passenger cars. This is typically achieved in the form of a boosted direct injection gasoline engine, which are typically equipped with variable valve timing (VVT) devices on the intake and/or exhaust valves. This paper describes the synergies between valve timings and boost based on experimental investigations in a single cylinder gasoline direct injection spark ignited (DISI) engine with variable cam phasing on both the intake and exhaust cams. Two cam profiles have been tested to realize Miller cycle and compared with the standard camshaft. One cam features a long opening duration and standard valve lift for Late Intake Valve Closing (LIVC) and the other cam has a short opening duration and low valve lift for Early Intake Valve Closing (EIVC).

The complexity of modern powertrain development is demonstrated by the combination of requirements to meet future emission regulations and test procedures such as Real Driving Emissions (RDE), reduction of fuel consumption and CO2 emissions as well as customer expectations for good driving performance. Gasoline engine downsizing is already established as a proven technology to reduce automotive fleet CO2 emissions. Additionally, alternative fuels such as natural gas, offer the potential to significantly reduce both tailpipe CO2 and other regulated exhaust gas emissions without compromising driving performance and driving range. This paper presents results showing how the positive fuel properties of natural gas can be fully utilised in a heavily downsized engine. The engine has been modified to cope with the significantly higher mechanical and thermal loads when operating at high specific outputs on compressed natural gas (CNG).