Search Results

Concerns over greenhouse gas emissions are driving governments and the automotive industry to seek out ways of reducing vehicle CO₂ emissions. Engine friction reduction is one means of reducing CO₂ emissions, through fuel consumption improvements. Of the different systems within the engine, the camshaft timing drive can contribute around 5 to 10% of the overall engine friction. It is therefore a system that can benefit from careful optimization. MAHLE has undertaken a motored friction-testing program on a 2.2-liter turbocharged diesel engine with the following different types of camshaft timing drive: - Chain drive with hydraulic tensioner. This is the standard configuration for this engine. - Chain drive with friction tensioner. - Wet belt drive. - Dry belt drive. Testing was conducted to allow the differences in friction between the different drive configurations to be calculated, by comparing each camshaft drive against the standard chain drive system.

An unmodified, conventionally fuelled, 2009 Class D vehicle with a 2.0L turbocharged gasoline direct injection engine was operated on a range of gasoline, gasoline-ethanol and gasoline-butanol fuel blends over NEDC drive cycles and WOT power curves on a chassis dynamometer. Engine performance, engine management system parameters and vehicle out emissions were recorded to investigate the response of a current state-of-the-art technology vehicle to various alcohol fuel blends. The vehicle fired on all fuels and was capable of adapting its long term fuelling trim to cope with the increased fuel flow demand for alcohol fuels up to E85. Over the NEDC tests, the volumetric fuel consumption was very strongly related to the calorific content of the fuel. CO and NOx emissions were largely unaffected for the mid alcohol blends, but CO emissions decreased and NOx emissions increased significantly for the high alcohol fuels. THC emissions were largely unaffected.

Concerns over greenhouse gas emissions are driving governments and the automotive industry to seek out ways of reducing vehicle CO₂ emissions. Engine friction reduction is one means of reducing CO₂ emissions, through fuel consumption improvements. The ancillary drive system typically contributes up to 8% of the total engine friction level, so improvements in this system can make a real difference to engine efficiency, fuel consumption and CO₂ emissions. Mahle has undertaken a series of rig tests, based on a 2.5-liter gasoline engine, but built to a minimum friction level of hardware. Using motored drive torques, the losses associated with different alternator drive concepts was investigated: - Standard 150A alternator, - Reduced capacity 120A alternator, - Reduced capacity 120A alternator driven by a dual speed gearbox, and - Reduced capacity 120A alternator driven by a twin-belt dual ratio pulley.

Concerns over greenhouse gas emissions are driving governments and the automotive industry to seek out ways of reducing vehicle CO₂ emissions. Engine friction reduction is one means of reducing CO₂ emissions, through fuel consumption improvements. One area where it is felt that friction reduction is possible is in connection with the camshaft bearings. Mahle has conducted experimental evaluation of rolling element bearings used to support camshafts, replacing the standard plain journal bearings. The aim of the testing was to gain an understanding of the durability of rolling element bearings, tested in a range of different operating conditions. The controlled test conditions included variations to: - Camshaft speed, - Oil temperature, - Oil age/specification, - Oil supply method/flowrate, - Bearing journal line bore misalignment tolerance, and - Bearing journal diametrical tolerance.

Concerns over greenhouse gas emissions are driving governments and the automotive industry to seek out ways of reducing vehicle CO₂ emissions. Engine friction reduction is one means of reducing CO₂ emissions, through fuel consumption improvements. One area where it is felt that friction reduction is possible is in connection with the camshaft bearings. The use of rolling element bearings is generally considered to provide friction reductions by two means: 1. As a direct substitution of the journal bearings by rolling element bearings and 2. As an enabling opportunity to reduce the oil flow requirement of the engine. MAHLE has undertaken a motored friction-testing program on a 2.5-liter gasoline engine, comparing the drive torques associated with the standard camshaft bearings and also with camshafts supported by rolling element bearings. The test engine incorporated a direct-acting valve train design.

The automobile industry is under intense pressure to reduce carbon dioxide (CO2) emissions of vehicles. There is also increasing pressure to reduce the other tail-pipe emissions from vehicles to combat air pollution. Electric powertrains offer great potential for eliminating tailpipe CO2 and all other tailpipe emissions. However, current battery technology and recharging infrastructure still present limitations for some applications, where a continuous high-power demand is required. Furthermore, not all markets have the infrastructure to support a sizeable electric fleet and until the grid energy generation mix is of a sufficiently low carbon intensity, then significant vehicle life-cycle CO2 savings could not be realized by the Battery Electric Vehicles. This investigation examines the effects of combustion, efficiencies, and emissions of two alcohol fuels that could help to significantly reduce CO2 in both tailpipe and the whole life cycle.

Vehicle manufacturers are facing increasing legislative pressure to reduce vehicle emissions and achieve zero tailpipe CO2 emissions within the coming decade. The focus on techniques to reduce the tailpipe CO2 emissions, rather than vehicle lifecycle emissions, naturally dictates electrified solutions. However, this will not address the increased emissions resulting from vehicle manufacture, the emissions of the legacy fleet, or enable niche or classic applications, to be decarbonised for future use. The use of bio-derived fuels, and fully synthetic fuels, can provide a technical solution to these challenges, but it is beneficial if these can be used as a drop-in replacement to existing fossil derived fuels, as this would enable straight-forward backward compatibility with existing vehicles and avoid the need to re-engineer future engine designs or upgrade existing hardware.

Emissions legislation, fleet CO₂ targets and customer demands are driving the requirements for reducing fuel consumption. This is being achieved in the gasoline market in the near term through the adoption of engine downsizing. In order to reduce fuel consumption further and in the wider real-world operating region complimentary technologies are being investigated and applied to an extreme downsized engine. In this paper future gasoline engine technologies are applied and experimentally assessed in terms of fuel consumption improvement whilst the impact of subsequent loadings on the thermal management system have been simulated, both over drive cycle and using real-world drive data.

The open MAHLE Flexible ECU (MFE) was developed and successfully implemented for controlling gasoline, diesel and hybrid engines. The increased demand of new functions development to address future powertrain challenges, such as lower fuel consumption, ever more stringent emissions legislative targets as well as the need to reduce development time and cost at the same time, led to the incorporation of the MFE functions in a co-simulation environment. The co-simulation environment consists of using the virtual engine developed with 1D or 3D numerical simulation tools and the functions of MFE developed with Simulink-Targetlink. This co-simulation approach allows modifying either the engine control or the engine itself. Regarding the engine control and its development, the existing and new functions were tested for the performance, emissions and behaviour changes on several production and prototype engines.

Today the light-duty commercial market is dominated by internal combustion engine powered vehicles, primarily diesel-powered delivery vans, which contribute to urban air quality issues. Global concerns regarding climate change have prompted zero emission vehicles to be mandatory in many markets as soon as 2035. For the light-duty commercial vehicle sector there is significant interest in pure electric vehicles. However, for some markets, or usage cases, electric vehicles may not be the best solution due to practical limitations of battery energy storage capacity or recharging times. For such applications there is growing interest in hydrogen fuel cells as a zero emissions alternative. Bramble Energy’s patented printed circuit board (PCB) fuel cell technology (PCBFC™) enables the use of cost-effective production methods and materials from the PCB industry to reduce the cost and complexity of manufacturing hydrogen fuel cell stacks.

This paper investigates the energy efficiency and emissions benefits possible with connected and autonomous vehicles (CAVs). Such benefits could be instrumental in decarbonising the transport sector. The impact of CAV technology on operation, usage and specification of vehicles for optimised energy efficiency is considered. Energy consumption reductions of 55% – 66% are identified for a fully autonomous road transport system versus the present. 46% is possible for a CAV on today’s roads. Smoothing effects and reduced stoppage in the drive cycle achieve a 31% reduction in travel time if speed limits are not reduced. CAV powertrain optimised for different scenarios requires just 10 kW – 40 kW maximum power whilst the vehicle mass is reduced by up to 40% relative to current cars. Urban-optimised powertrain, with only 10 kW – 15 kW maximum power, allows energy consumption reductions of over 71%.

In 2012 MAHLE Powertrain developed a range-extended electric vehicle (REEV) demonstrator, based on a series hybrid configuration, and uses a battery to store electrical energy from the grid. Once the battery state of charge (SOC) is depleted a gasoline engine (range extender) is activated to provide the energy required to propel the vehicle. As part of the continuing development of this vehicle, MAHLE Powertrain has developed control software which can intelligently manage the use of the battery energy through the combined use of GPS and road topographical data. Advanced knowledge of the route prior to the start of a journey enables the software to calculate the SOC throughout the journey and pre-determine the optimum operating strategy for the range extender to enable best charging efficiency and minimize NVH. The software can also operate without a pre-determined route being selected.

Particulate emissions are of growing concern due to health impacts. Many urban areas around the world currently have particulate matter levels exceeding the World Health Organisation safe limits. Gasoline engines, especially when equipped with direct injection systems, contribute to this pollution. In recognition of this fact European limits on particulate mass and number are being introduced. A number of ways to meet these new stringent limits have been under investigation. The focus of this paper is on particulate emissions reduction through improvements in fuel delivery. This investigation is part of the author's ongoing particulate research and development that includes optical engine spray and combustion visualisation, CFD method development, engine and vehicle testing with the aim to move particulate emission development upstream in the development process.