Search Results

Spray-guided gasoline direct injection SI engines attract as one of new generation lean-burn engines to promise CO2 reduction. These typically adopt “narrow-spacing” concept in which an injector is centrally mounted close to a spark plug. Therefore, geometric targets of the fuel spray and a position of the spark plug have to be exactly limited to maintain a proper mixture in the spark gap. In addition, the stable combustion window is narrow because the spark ignition is limited in a short time during and immediately after the injection. These spatial and temporal restrictions involve some intractable problems concerning the combustion robustness due to the complicate phenomena around the spark plug. The local mixture preparation near the spark plug significantly depends on the spray-induced charge motion. The intense flow induced by the motion blows out and stretches the spark, thereby affecting the spark discharge performance.

The objective of this study was to develop a test method for heavy-duty HEVs using a hardware-in-the-loop simulator (HILS) to enhance the type-approval-test method. To achieve our objective, HILS systems for series and parallel HEVs were actually constructed to verify calculation accuracy. Comparison of calculated and measured data (vehicle speed, motor/generator power, rechargeable energy storage system power/voltage/current/state of charge, and fuel economy) revealed them to be in good agreement. Calculation error for fuel economy was less than 2%.

Soot accumulation in diesel engine crankcase is the dominant factor which governs engine oil drain interval. So, efficient soot elimination from crankcase oil can be a practical way to achieve drain interval extension. Combination of high performance oil filter and low soot dispersancy oil results in an effective measure to trap soot efficiently. In this paper, the behavior of newly developed high performance diesel engine oil having low soot dispersancy is reported. Prior to oil development, an evaluation method of soot dispersancy in oil was elaborated. Based on relative viscosity defined as ratio of soot containing oil viscosity to soot eliminated oil viscosity, dispersancy parameter was determined. Oil dispersancy evaluated on this parameter agreed with the results obtained from particle size analyzer. Secondly, a method to obtain oil filter soot trap rate to total soot contaminated into crankcase (trap rate) was established.

GDI (Gasoline Direct Injection) engine adopting new combustion control technologies was developed and introduced into Japanese domestic market in August of 1996. In order to extend its application to the European market, various system modifications have been performed. Injectors are located with a smaller angle to the vertical line in order to improve the combustion stability in the higher speed range. A new combustion control method named “two-stage mixing” is adopted to suppress the knock in the low speed range. As a result of this new method, the compression ratio was increased up to 12.5 to 1 while increasing the low-end torque significantly. Taking the high sulfur gasoline in the European market into account, a selective reduction lean-NOx catalyst with improved NOx conversion efficiency was employed. A warm-up catalyst can not be used because the selective reduction lean NOx catalyst requires HC for the NOx reduction.

Spray motion visualization, mixture strength measurement, flame spectral analyses and flame behavior observation were performed in order to elucidate the mixture preparation and the combustion processes in Mitsubishi GDI engine. The effects of in-cylinder flow called reverse tumble on the charge stratification were clarified. It preserves the mixture inside the spherical piston cavity, and extends the optimum injection timing range. Mixture strength at the spark plug and at the spark timing can be controlled by changing the injection timing. It was concluded that reverse tumble plays a significant role for extending the freedom of mixing. The characteristics of the stratified charge combustion were clarified through the flame radiation analyses. A first flame front with UV luminescence propagates rapidly and covers all over the combustion chamber at the early stage of combustion.

With the intention of improving engine performance and emissions, the authors examined the influence of the method of initial fuel injection quantity reduction and of the injector configuration of a common rail fuel injection system on engine performance and exhaust emissions. Results showed that decreasing the nozzle hole diameter was an effective way to reduce the initial injection quantity without increasing black smoke. Compared to a three-way type injector, it was found that a two-way type injector can greatly reduce the amount of fuel leakage from the electromagnetic injector control valve and fuel consumption could be further improved by reduction of the driving loss. Furthermore, the increase of driving losses with higher injection pressure was small, and as a result, higher pressure injection was possible.

Protection of the Earth's environment by means of energy saving and cleaning up of air pollution on a global scale is one of the most important subjects in the world today. Because of this, the requirements for better fuel economy and cleaner exhaust emissions of internal combustion engines have been getting stronger, and, in particular, simultaneous reduction in nitrogen oxides (NOx) and particulate matter (PM) from heavy-duty diesel engines (HDDEs) without degrading fuel economy has become a major subject. Mitsubishi Motors Corporation (MM) has been selling diesel-powered heavy-duty trucks in the U.S. market since 1985 and has agressively carried out development work for meeting the 1991 model year exhaust emission standards.

Injection rate control is an important capability of the ideal injection system of the future. However, in a conventional Common-Rail System (CRS) the injection pressure is constant throughout the injection period, resulting in a nearly rectangular injection rate shape and offering no control of the injection rate. Thus, in order to realize injection rate control with a CRS, a "Next- generation Common-Rail System (NCRS)" was conceptualized, designed, and fabricated. The NCRS has two common rails, for low- and high-pressure fuel, and switches the fuel pressure supplied to the injector from the low- to the high- pressure rail during the injection period, resulting in control over the injection rate shape. The effects of injection rate shape on exhaust emissions and fuel consumption were investigated by applying this NCRS to a single- cylinder research engine.

In Biodiesel Fuel Research Working Group(WG) of Japan Auto-Oil Program(JATOP), some impacts of high biodiesel blends have been investigated from the viewpoints of fuel properties, stability, emissions, exhaust aftertreatment systems, cold driveability, mixing in engine oils, durability/reliability and so on. In the impact on exhaust emissions, the impact of high biodiesel blends into diesel fuel on diesel emissions was evaluated. The wide variety of biodiesel blendstock, which included not only some kinds of fatty acid methyl esters(FAME) but also hydrofined biodiesel(HBD) and Fischer-Tropsch diesel fuel(FTD), were selected to evaluate. The main blend level evaluated was 5, 10 and 20% and the higher blend level over 20% was also evaluated in some tests. The main advanced technologies for exhaust aftertreatment systems were diesel particulate filter(DPF), Urea selective catalytic reduction (Urea-SCR) and the combination of DPF and NOx storage reduction catalyst(NSR).

A two-stage combustion is one of the Mitsubishi GDI™ technologies for a quick catalyst warm-up on a cold-start. However, when the combustion is continued for a long time, an increase in the fuel consumption is a considerable problem. To solve the problem, a stratified slight-lean combustion is newly introduced for utilization of catalysis. The stratified mixture with slightly lean overall air-fuel ratio is prepared by the late stage injection during the compression stroke. By optimizing an interval between the injection and the spark timing, the combustion simultaneously supplies substantial CO and surplus O2 to a catalyst while avoiding the soot generation and the fouling of a spark plug. The CO oxidation on the catalyst is utilized to reduce the cold-start emissions. Immediately after the cold-start, the catalyst is preheated for the minimum time to start the CO oxidation by using the two-stage combustion. Following that, the stratified slight-lean combustion is performed.

NOx adsorber has already been used for the after-treatment system of series production vehicle installed with a lean burn or direct injection engine [1,2,3]. In order to improve NOx adsorbability at high temperatures, many researchers have recently been trying an addition of potassium (K) as well as other conventional NOx adsorbents. Potassium, however, reacts easily with the cordierite honeycomb substrate at high temperatures, and not only causes a loss in NOx adsorbability but also damages the substrate. Three new technologies have been proposed in consideration of the above circumstances. First, a new concept of K-capture is applied in washcoat design, mixed with zeolite, to improve thermal stability of K and to keep high NOx conversion efficiency, under high temperatures, of NOx adsorber catalyst. Second, another new technology, pre-coating silica over the boundary of a substrate and washcoat, is proposed to prevent the reaction between potassium and cordierite.

Analysis results of used oils sampled from many engines operating in the field show that the most critical factor governing the limits of oil use is insoluble fraction concentration in oil. Hence, the authors developed a new oil and by-pass oil filter to increase soot trapping efficiency, so as to extend oil change interval. Soot trapping efficiency could be improved from 30% to more than 80% using a bigger oil filter with fine mesh and a newly developed low soot dispersancy oil. Engine lubrication performance of the new oil was compared to that of standard and commercial long-drain oils by conducting 300-hour endurance tests on an 11.7 liter direct injection, turbocharged and aftercooled diesel engine at rated output. Test results proved superior engine lubrication performance of the new oil. THE INTERVAL between lubricating oil changes for diesel engines is twenty to forty thousand kilometers, depending on engine manufacturers' recommendations (1)*.

A stratified-charge lean-burn engine is newly developed for the purpose of energy saving and carbon dioxide reduction to minimize the global warming. The engine, named MVV(Mitsubishi Vertical Vortex)engine, is based on the unique vertical vortex technology which realizes stable combustion even with lean mixture without any additional device. And it also has another feature of “all range air-to-fuel ratio feedback control system” utilizing linear air-to-fuel ratio sensor. This paper describes various technologies developed in this engine.

For meeting more stringent regulations to be imposed for reducing particulate matter (PM) in exhaust gas from diesel engines, it is required to improve performance of a trap system or other post-processing devices as well as fuel combustion efficiency of the engine itself. In the trap system, a trap filter is equipped to collect PM from exhaust gas. For continuous use of the trap filter, a regenerative processing must be carried out to remove PM by means of forced burning when a certain amount of PM has been trapped. The combustibility or burning characteristics of collected PM have a significant effect on the regenerative processing with an electric heater/burner. To clarify the combustibility of PM collected in the trap filter, we have examined the relationships between engine drive conditions (exhaust gas temperature), PM characteristics, and combustibility.

Several types of oxidation catalyst material are tested in repeated particulate emission measurements over the US HDD transient test procedure. Particulates are effectively reduced in the initial stage of the measurements. However, particulates tend to increase when repeating the measurements. This is believed to be caused by sulfate adsorption on the catalyst surfaces. Hence, oxidation catalysts are tested after stabilizing surface adsorption. Test results show that an oxidation catalyst which forms more sulfates is not effective in reducing particulates because the sulfate increase offsets the SOF reduction effect. An effective catalyst for particulate reduction is developed by suppressing sulfate formation.

In the heavy-duty commercial vehicle market in Japan, particularly in the segment of dump trucks and tractors, naturally aspirated engines maintain a dominant market share because of their superior torque characteristics in the low speed range. In order to meet the ever increasing needs for higher speeds of transportation, better fuel economy and higher reliability, and the needs for increasingly strict exhaust emission regulations, Mitsubishi Motors Corporation (MMC) has developed the 8M20, a 20 liter V8 diesel engine. The '92 model series of “THE GREAT”, MMC's main heavy-duty trucks, has featured this new and powerful engine and has been in the market place since October, 1991. The 8M20 is a naturally aspirated engine that provides an output of 294kW/2200rpm, complying with the current Japanese exhaust emission regulations.

A trap system has been developed that collects particulate using two small filters and regenerates alternately by electric heaters. This system contains a new idea in detection of the amount of particulate accumulation in the filters. The system counts the amount using a particulate accumulation rate map which is a function of the engine load and speed. In vehicle test with this trap system, the particulate collection efficiency and the regeneration efficiency were proved to be high enough for practical use. The test results also showed that the shutdown performance of the route switch valve greatly influenced the regeneration efficiency.

To improve vehicle startability and transient response of turbocharged diesel trucks, their phenomena have been investigated and analyzed in detail and various supercharging systems have been developed and installed on a truck for comparison of their characteristics. The systems considered were ceramic, variable geometry, variable entry,and air-assisted turbochargers and a combined supercharging system. The variable entry turbocharger has two turbine scrolls with different nozzle areas and two switching valves to get three different turbine flow capacities. The combined supercharging system consists of a mechanical supercharger and a turbocharger. These are linked in series. Both work in a low engine speed range, and the turbocharger only works in middle and high engine speed ranges. Among these systems, the combined supercharging system is the best for improving both vehicle startability and transient response of a truck.

To meet the increasingly strong demand for high-speed transportation, better fuel economy, higher reliability and the social requirements for more strict Japanese regulations against exhaust and noise emissions, Mitsubishi Motors Corporation has recently developed the 6D40T1 in-line 6-cylinder, 12.0-liter turbocharged and intercooled diesel engine for heavy-duty trucks. This engine meets the 1989 Japanese exhaust emission regulations and has an output of 258 kW. To achieve both fuel economy and good drivability, Mitsubishi's original, electronically-controlled fuel injection system was adopted. The so-called prestroke-controlled fuel injection pump is capable of flexible and precise control of both fuel injection rate and timing. The basic structure of the 6D40T1 was designed with high rigidity to permit high cylinder pressures. In addition, to reduce friction and heat losses, a 4-valve design, roller cam followers with needle roller bearings, and shortened exhaust ports were adopted.

The characteristics of a new diesel particulate filter material made of SiC were studied through engine tests in varying material properties, such as average pore diameter, and wall thickness. Compared to a conventional cordierite filter of the same size, particulate trapping efficiency is almost the same, and the pressure loss and the deterioration of fuel consumption can be reduced to about half with the optimum material properties. If the same pressure loss is allowed, the filter size can be reduced by 30%. Its good thermal conductivity prevents local temperature increases, which doubles the permissible amount of trapped particulates. As heat crack problems occurred in integral-type filters due to the high thermal expansion of SiC, a split-type filter having 49 filter segments with a square section was developed.