Refine Your Search

Search Results

Viewing 1 to 14 of 14
Technical Paper

Forming Performance of Aluminum Alloy Sheets for Automobile Body Panels

1995-02-01
950924
Improvement of material characteristic values, adjustment of forming conditions as well as introduction of new forming technics are necessary to promote wide application of aluminum alloy sheets into automotive parts. 5000 series and 6000 series aluminum alloy sheets are concerned about the relationship between material characteristic values and fundamental forming ability required to apply them to automobile body parts as well as the effect of lubricant on their formability. The hardening parameters, n values, of them are larger than those of cold-rolled steel sheets. However, the r values and the local elongations are extremely small. The improvement of stretch formability owing to increase of n value is smaller than that of the steel sheets. Inferior deep drawability of the aluminum alloy sheets is due to low fracture resistance force caused by low r value.
Technical Paper

Metal Flow of a Tailored Blank in Square Cup Deep Drawing

1998-02-23
980447
The application of tailored blanks to autobody parts has progressed because of its numerous advantages. The forming of tailored blanks has, however, a lot of technical problems. Among the problems, weld-line movement and formability deterioration are the most significant ones in case of deep drawing. The weld-line movement and formability change were examined experimentally as a function of weld-line location in square cup deep drawing. The weld-line movement of tailored blank consists of two sources. One is the geometrical reason, and the other is due to the hardening of weld bead. The formability of tailored blank is inferior to that of an original blank by the existence of hardened weld region. The mode of fracture changes from wall breakage to a fracture adjacent to punch radius when the weld-line was close to the punch corner.
Technical Paper

Application of Vibration Damping Steel Sheet for Autobody Structural Parts

1992-02-01
920249
As a demand for vehicles of higher functionality grows, automakers and material suppliers are devoting increasing efforts to develop technologies for greater safety, lighter weight, higher corrosion resistance, and enhanced quietness. The resin-sandwiched vibration damping steel sheet (VDSS), developed as a highly functional material for reducing vehicle vibration and noise, has been used for oil pans1) and compartment partitions2). First applied for a structural dash panel of the new Mazda 929, a Zn-Ni electroplated VDSS which allows direct electric welding has contributed to greater weight reduction as well as improved quietness.
Technical Paper

Recent Developments in Press Formability of Aluminum Alloy Sheets for Automotive Panels

1993-03-01
930705
Aluminum alloy sheets are used for automotive body-panels, but their small Young's modulus results in inferior shape-fixability than conventionally-applied steel sheets with similar strengths. Smaller radius of curvature, indicating better shape-fixability, is found at the center of a panel press-formed with higher blank holder force (BHF). Higher force can be applied for press-forming of alloy sheets with larger strain-hardening exponent (n value) induced by an increased addition of Mg. Recently-developed 5000 series alloy sheets containing 5.5 pct Mg and 0.3 pct Cu have an elongation over 33 pct at an ultimate tensile strength of 270 MPa and can be press-formed with better shape-fixability.
Technical Paper

Extremely Formable Cold Rolled Sheet Steel with Ultra-High Lankford and n Values - Metallurgy and Formabilities

1993-03-01
930783
Extremely formable cold sheet steel with an ultra-high Lankford value of more than 2.5 and an n value of more than 0.27 has been developed. This steel is obtained due to the following factors; using extremely pure IF (Interstitial free) steel, immediate rapid cooling upon completion of rolling in the hot rolling process, a high reduction in the cold rolling process, and a high soaking temperature in the continuous annealing process. This steel sheet shows excellent deep drawability and stretch formability compared with conventional steel sheet (former IF steel and low carbon aluminum-killed steel) as a result of evaluating the limiting drawing ratio and limiting dome height, respectively. This excellent formability is also shown by the model forming tests for simulating the actual stamping of an oilpan and a side-panel. Furthermore, this steel shows the same spot-weldability as that of former IF steel, and zinc phosphatability similar to that of low carbon aluminum-killed steel.
Technical Paper

Predictive Evaluation of Sheet Metal Forming Limit Using 3-D FEM

1993-03-01
930519
This paper describes the deformation analysis of hemispherical punch stretching and square shell drawing, using 3-D finite element program “ROBUST”. The effects of material properties and process factors on cup height to punch force relation, and strain distributions on formed parts were investigated. The calculated values give considerably good agreement with experimental measurements from LDH, FLD and square shell tests. The results can be expected to contribute to predictive evaluation of forming limits using computer simulation.
Technical Paper

An Evaluation of Fatigue Strength for Various Kinds of Spot-Welded Test Specimens

1988-02-01
880375
Eight kinds of the spot-welded test specimens were studied to obtain the basic fatigue data on steel sheets for car bodies. Analytical methods such as the strain amplitude at outside and inside plates close to the nugget, the maximum nominal stress and Kθmax criteria of fracture mechanics were used. The authors propose that the ratio of strains at two points around the nugget can provide evaluation of the bending load and estimation of the fatigue strength.
Technical Paper

Properties of a Newly Developed Organic Composite Coated Steel Sheet for Automotive Use

1992-02-01
920172
The newly developed sheet steel lightly coated with an organic composite is as follows. Zn-Ni alloy plated sheet steel with a coating weight of 30 g/m2 and average Ni concentration of 11.5 ∼12.0 % is chromated through electrolysis. The coating weight of chromate film is 50 ∼90 mg/m2 in Cr. Furthermore, emulsified olefin-acrylic acid copolymer resin mixed with colloidal silica of particle size 7 ∼8 nm applied to a thickness of 1.0 ∼1.8 μm. Olefin-acrylic acid copolymer resin and colloidal silica are mixed at the rate of 100 and 30 (parts by weight). It maintains excellent corrosion resistance even after forming, C-ED paint corrosion resistance and paint adhesion. Furthermore, it has excellent perforation resistance. The product has excellent weldability and is well suited to continuous forming, too.
Technical Paper

High Temperature Carburizing Steel Bars for Saving Energy Consumption in the Automobile Industry

1982-02-01
820127
Carburizing heat treatment is one of the automobile component manufacturing steps, which consumes a large amount of energy. Raising the carburizing temperature can shorten the carburizing time and save the energy, but involves the risks of grain coarsening and attendant property deterioration. The authors have clarified the precipitation behavior of aluminum nitride (A1N) in the automobile gear manufacturing process and the optimum precipitation of A1N in as-rolled steel bars to prevent the grain coarsening. Through the application of the controlled rolling technique to ensure the optimum precipitation of A1N in continuously cast steel of uniform chemical composition, the authors have substantially saved energy while maintaining high quality, and developed a high-temperature carburizing steel expected to minimize and stabilize quenching strains.
Technical Paper

A New Method of Stress Calculation in Spot Welded Joint and Its Application to Fatigue Life Prediction of Actual Vehicle

2003-10-27
2003-01-2809
A method of fatigue life prediction of spot welded joint under multi-axial loads has been developed by fatigue life estimation working groups in the committee on fatigue strength and structural reliability of JSAE. This method is based on the concept of nominal structural stress ( σ ns) proposed by Radaj and Rupp, and improved so that D value is not involved in stress calculation. The result of fatigue life estimation of actual vehicle with nominal structural stress which was calculated through newly developed method had very good correlation with the result of multi-axial loads fatigue test carried out with test piece including high strength steel.
Technical Paper

Fatigue life prediction for welded steel sheet structures

2003-10-27
2003-01-2878
In this paper the fatigue life of welded steel sheet structures is predicted by using FE-Fatigue, which is one of fatigue analysis software tools on the market, and these predicted results are evaluated by reference to corresponding experimental results. Also, we try to predict these structures by using two fatigue life prediction theories established by the JSAE fatigue and reliability committee to compare prediction results. It was confirmed that spot welds fatigue life predictions agree qualitatively with corresponding experimental results and arc welds fatigue life predictions are in good agreement with corresponding experimental results in cases where the SN curve database is modified appropriately.
Technical Paper

Integration of process operation in the fatigue calculation of sheets structural parts

2003-10-27
2003-01-2879
The main operations for the manufacturing of auto parts are the cutting of the flange and the stamping. In order to perform accurate fatigue calculation it is necessary to have the material properties for each point of the structure. Usually, only the fatigue curve obtained on the flat sheet with polished edges is used because it represents the basic metal behaviour. The real edge quality decreases the fatigue limit while the hardening induced by the stamping increases it. To take these effects into account allows a better fatigue calculation of the structural part.
Technical Paper

High-Strength Cold-Rolled Steels Produced by Continuous Annealing and Their Automotive Applications

1981-02-01
810028
In continuous annealing, accelerated cooling methods have recently found practical application in addition to conventional gas jet cooling or water jet quenching method. Moderate cooling rate of gas jet cooling or accelerated cooling makes it possible to utilize new high-strength steels with excellent properties. The faster cooling rate deteriorates ductility of steels. These newly developed steels are improved rephosphorized steels with high r̄-value and high bake hardenability, dual phase steels with superior ductility, Ti-stabilized high-strength steels with very high r̄-value, grain boundary hardening steels employing low temperature annealing, and unique ultra high-strength steels. This paper describes properties and process factors of these steels, and their applications to automotive.
Journal Article

Development of Precision Rolling Machine

2010-04-12
2010-01-0978
This paper proposes a rolling machine that forms fine corrugated section patterns for thin sheets. A prototype of the machine was made and the performance of the machine was tested. As compared with press forming, rolling has the advantages of the high forming limit, the low forming reaction force, the easy control of the thin sheet's curve and high productivity. We confirmed these four advantages by using finite element analyses and the prototype rolling machine. Stainless steel sheets and titanium sheets, which were one of the materials with a low forming limit, were used. Firstly, the rolling showed a 1.3-times higher forming limit than the press forming in the case that a fine corrugated section pattern was formed in a stainless steel sheet of 22-mm square sizes. Secondly, the forming reaction force of the rolling was about one-twentieth of the press forming without coining, and the experimental results agreed with the finite element simulation.
X