Refine Your Search

Topic

Search Results

Viewing 1 to 19 of 19
Technical Paper

Development of Pitting Resistant Steel for Transmission Gears

2001-03-05
2001-01-0827
It was found that pitting resistance of gears is strongly influenced by resistance to temper softening of carburized steel. The investigation about the influence of chemical compositions on hardness after tempering revealed that silicon, chromium and molybdenum are effective elements to improve resistance to temper softening and pitting resistance. Considering the production of gears, molybdenum is unfavorable because it increases hardness of normalized or annealed condition. Developed new steel contains about 0.5 mass% of silicon and 2.7 mass% chromium. The new steel has excellent pitting resistance and wear resistance. Fatigue and impact strength are equivalent to conventional carburized steels. Cold-formability and machinability of the new steel are adequate for manufacturing gears because of its ordinary hardness before carburizing. The new steel has already been put to practical use in automatic transmission gears. Application test results are also reported.
Technical Paper

Development of a High-Performance TiA1 Exhaust Valve

1996-02-01
960303
A new high-performance and lightweight TiA1 intermetallic compound exhaust valve has been developed. The TiA1 valve can improve power output and fuel economy by contributing higher engine speeds and a reduction in valvetrain friction. It was achieved by developing a Ti-33.5A1-0.5Si-1Nb-0.5Cr (mass%) intermetallic compound, a precision casting method for TiA1 that provides a low-cost, high-quality process, and a plasma carburizing technique for assuring good wear resistance on the valve stem end, stem and face.
Technical Paper

Development of a Valve Train Wear Test Procedure for Gasoline Engine Oil

1994-03-01
940794
An analysis was made of wear factors by investigating the effect of engine operating conditions on valve train wear. It was found that cam nose wear increased as larger amounts of combustion products, including nitrogen oxides and unburned gasoline, became intermixed with the engine oil. Based on these results, a valve train wear test procedure has been developed for evaluating cam nose and rocker arm wear under engine firing conditions. It has been confirmed that this test procedure correlates will with ASTM Sequence VE test and CCMC TU-3 test.
Technical Paper

The Effect of Belt-Drive CVT Fluid on the Friction Coefficient Between Metal Components

1997-10-01
972921
A block-on-ring friction and wear testing machine (LFW-1) was used as a test method for making fundamental evaluations of the effect of the Belt-Drive Continuously Variable Transmission(B-CVT) fluid on the friction coefficient between the belt and pulleys. The results confirmed that this method can simulate the friction phenomena between the belt and pulleys of an actual transmission. The mechanism whereby ZDDP and some Ca detergents improve the torque capacity of a B-CVT was also investigated along with the effect of the deterioration of these additives on the friction coefficient. It was found that these additives form a film, 80-90 nm in thickness, on the sliding surface, which is effective in increasing the friction coefficient. The friction coefficient declined with increasing additive deterioration. The results of a 31P-NMR analysis indicated that the decline closely correlated with the amount of ZDDP in the B-CVT fluid.
Technical Paper

Establishment of a Method for Predicting Cam Follower Wear in the Material Development Process

1990-10-01
902087
Many studies have been reported concerning fundamental tribological research aimed at reducing the severe valve train wear that occurs in internal combustion engines. In this paper, cam follower wear was theoretically and experimentally analyzed at the material development stage. Statistical methods have been applied to practical use in determining the material properties quantitatively. Based on the results, a method for predicting cam follower wear has been derived which has made it possible to develop new valve train systems more efficiently. Further, a guideline for developing new wear resistant materials was also clarified. Finally, the precision high chrominum cast iron rocker arm is described, along with its application to a new NISSAN high-performance 4-cylinder DOHC engine, as an example of the use of this method to develop new wear-resistant materials.
Technical Paper

Development of Practical Heads-Up Display for Production Vehicle Application

1989-02-01
890559
THIS PAPER presents an advanced heads-up display which has been newly developed for use in 88 Nissan Silvia model. The HUD consists of a projector with a newly developed high brightness VFD and light-selective film used as a combiner which is coated on the windshield. This combination provides good display legibility even under bright sunlight. The display shows the vehicle speed in a three-digit reading at distance of more than one meter from the driver's eyes. The windshield-coated combiner conforms to U.S. safety standards concerning light transmittance, abrasion and other performance requirements. Experimental data are also presented which substantiate the HUD's high legibility and confirm its effect in enhancing the driver's attention toward the road ahead
Technical Paper

A Method for Predicting Connecting Rod Bearings Reliability Based on Seizure and Wear Analysis

1988-02-01
880568
Maintaining reliability of the connecting rod bearing is a very important subject, and the following is a problem that needs to be overcome. Predicting reliability has generally depended on minimum oil film thickness (M.O.F.T), but recently, the engines of passenger cars which have greater power and speed potential than conventional ones are sometimes run beyond their M.O.F.T. limit (a degree of roughness around the crank shaft's axis.) In such a case, it is so difficult to predict reliability according to M.O.F.T., that we need a new index which directly shows seizure and wear. For this purpose, we found that the crank shaft pin temperature can be a key cause of seizure and wear according to an analysis of the relationship between its temperature and the seizure and wear caused intentionally. Using this method, we confirmed that the combination of bearing and crank shaft materials is very important for preventing seizure and wear.
Technical Paper

Evaluation of Passenger Car Gasoline Engine Oils by JASO Test Procedures—Report by JASO Engine Oil Subcommittee

1987-11-01
872122
Japan Automobile Standards Organization (JASO) Engine Oil Sub-committee have been working on the unification of the engine oil evaluation test procedures in Japan. The Engine Oil Sub-committee participated in the recent activity of the worldwide engine oil standardization of SAE and ISO. As one of the chain of activities, JASO tests M328, M331, and M333 (valve train wear, detergency and high temperature oxidation respectively) were conducted on the REOs of ASTM and CEC to find the correlation. The detergency tests (varnish and sludge) showed good correlation with the ASTM REOs. CEC good and poor reference oils seemed to give good results in JASO valve train wear test, while ASTM reference oils unexpectedly gave opposite results in Japanese valve train wear tests.
Technical Paper

New PM Valve Seat Insert Materials for High Performance Engines

1992-02-01
920570
Internal combustion engines experience severe valve train wear and the reduction of valve seat and seat insert wear has been a long-standing issue. In this work, worn valve seats and inserts were examined to obtain a fundamental understanding of the wear mechanisms and the results were applied in developing new valve seat insert materials. The new exhaust valve insert material for gasoline engines is a sintered alloy steel containing Co-base hard particles, with lead infiltrated only for inserts used in unleaded gasoline engines. The new intake valve insert material for gasoline engines is a high-Mo sintered steel, obtained through transient liquid phase sintering and with copper precipitated uniformly. This material can be used for both leaded and unleaded gasoline engines. Valve and valve seat insert wear has long been an issue of concern to engine designers and manufacturers.
Technical Paper

Current Trends of Passenger Car Gasoline Engine Oils in Japan - Report by JASO Engine Oil Subcommittee

1986-10-01
861512
Engines in Japan have higher output versus small displacement (bhp/liter) and require low phosphorus content in the engine oils to meet the most stringent exhaust emission regulation in the world. The market survey of typical API SF oils in Japan showed that the average phosphorus content was approximately 0.07 %. Under such circumstances engine oils provide good performance with the usage of secondary zinc di-alkyldithiophosphates (Zn DTP) for valve train wear protection, addition of friction modifiers for fuel economy, etc.
Technical Paper

Deterioration of Heat Resistant Alloys for Automobile Emission Control Equipment

1980-02-01
800318
Various heat resistant alloys are being introduced for use in automobile emission equipment, such as thermal reactors and catalytic converters. For the past several years Japan has been developing alloys which emphasize oxidation resistance. Therefore, oxidation phenomena have been thoroughly researched and clarified. On the other hand, embrittlement, which is a marked deterioration similar to oxide deterioration, has not been studied sufficiently. The major subjects of investigation were the two forms of embrittlement in austenitic heat resistant alloys, caused by the precipitation of σ phase and the absorption of Nitrogen. Useful information was obtained from these results.
Technical Paper

Development of Digital Tire Pressure Display Device

1985-06-01
851237
Basic vehicle performance, such as Safety, Comfort and Economy, are by dependent on tire performance, and it is the air pressure in the tire which assures this performance. However, tire air has a tendency to leak naturally, making it necessary to check them periodically. Since a deterioration in vehicle performance resulting from a drop on tire air pressure can not be directly felt by the driver, the number of people maintaining their tires sufficiently is relatively few. There have been many tire pressure warning devices developed which advise the driver when the pressure drops below a prescribed level. Differing from conventional devices, the TWD-III features a 7-step digital display (at a pitch of 0.1 kgf/cm2) which shows the pressure of each tire within an optional range, and it also has a flat tire warning function. The employment of echo effect from clystal vibrator resonance precludes the need to attach a power source on the tire.
Technical Paper

A Lubrication Analysis of Multi Link VCR Engine Components using a Mixed Elasto-Hydrodynamic Lubrication Theory Model

2009-04-20
2009-01-1062
Research is under way on an engine system [1] that achieves a variable compression ratio using a multiple-link mechanism between the crankshaft and pistons for the dual purpose of improving fuel economy and power output. At present, there is no database that allows direct judgment of the feasibility of the specific sliding parts in this mechanism. In this paper, the feasibility was examined by making a comparison with the sliding characteristics and material properties of conventional engine parts, for which databases exist, and using evaluation parameters based on mixed elasto-hydrodynamic (EHD) lubrication calculations. In addition, the innovations made to the mixed EHD calculation method used in this study to facilitate calculations under various lubrication conditions are also explained, including the treatment of surface roughness, wear progress and stiffness around the bearings.
Technical Paper

Simulation of Bearing Wear and Its Influence Upon Bearing Performance Based on Elastohydrodynamic Analysis

1999-05-03
1999-01-1522
This paper reports attempts to gain better understanding of the influence of bearing wear on the performance of hydrodynamically lubricated bearings. An analysis was carried out on bearings from a Sapphire bearing test rig using an elastohydrodynamic model. This involved the use of both the original and worn bearing surface profiles. The results indicated that bearing wear could improve the lubrication conditions. Also the progress of wear in the bearing was simulated using a simple model of the wear process. This model predicted that the wear would progress at a reducing rate. The predicted wear agreed well with measurements both in terms of the wear profile and the location of wear.
Technical Paper

Development of a Small Pitch Silent Chain for a Single-Stage Cam Drive System

1999-03-01
1999-01-1226
In contrast to the conventional two-stage cam drive system with a 9.52- mm pitch roller chain, a newly developed silent chain with a 6.35-mm pitch has made it possible to achieve a single-stage system. One traditional drawback of silent chains has been wear elongation. In developing the new chain, reliability was substantially improved by identifying the factors causing wear elongation and their effects and also by optimizing the characteristics of the chain components. The application of this single-stage cam drive system to the new QG engine series has resulted in reduced chain noise, a more compact cylinder head and significant weight savings due to the smaller part count and other improvements.
Technical Paper

Development of the Sequence IVA Valve Train Wear Lubricant Test: Part 1

2000-06-19
2000-01-1820
The ASTM Sequence VE test evaluates lubricant performance for controlling sludge deposits and minimizing overhead camshaft lobe wear. ILSAC asked JAMA to develop a new valve train wear replacement test since the Sequence VE test engine hardware will become obsolete in the year 2000. JAMA submitted the JASO specification M 328-951) KA24E valve train wear test. This first report presents the results of technical studies conducted when JASO M 328-95 was reviewed and the ASTM standardized version of the KA24E test (the Sequence IVA) was proposed. The cam wear mechanism was studied with the goal of improving reproducibility and repeatability. Engine torque was specified to stabilize the NOx concentration in blow-by, which improved test precision. Additionally, the specifications for induction air humidity and temperature, oil temperature control, and test fuel composition were modified when the ASTM version of the KA24E test was proposed.
Technical Paper

A Study on Engine Bearing Wear and Fatigue Using EHL Analysis and Experimental Analysis

1999-05-03
1999-01-1514
The possibility of predicting engine bearing durability by elastohydrodynamic lubrication (EHL) calculations was investigated with the aim of being able to improve durability efficiently without conducting numerous confirmation tests. This study focused on the connecting rod big-end bearing of an automotive engine. The mechanisms of wear and fatigue, which determine bearing durability, were estimated by comparing the results of EHL analysis and experimental data. This comparison showed the possibility of predicting the wear amount and the occurrence of fatigue by calculation.
Technical Paper

Development of a Wear Resistant Aluminum Alloy for Automotive Components

1999-03-01
1999-01-0350
Hypereutectic Al-Si alloy 390, containing large amounts of hard silicon particles, has mainly been used for wear-resistant alloy applications. In the case of hypereutectic Al-Si alloys, the primary silicon particle size and distribution must be controlled to obtain stable wear resistance. The service life of furnaces and molds is shortened by the high melting and casting temperatures required for controlling primary silicon. Furthermore, machinability is degraded by large primary silicon particles. To overcome these problems, a new wear-resistant Al-Si alloy has been developed which provides good castability and machinability. This alloy also has wear resistance and mechanical properties similar to those of the 390 alloy. Specifically, the problems regarding castability and machinability were solved by decreasing the silicon content of the 390 alloy, but that also reduced wear resistance.
Journal Article

Development of Low Viscosity API SN 0W-16 Fuel-Saving Engine Oil Considering Chain Wear Performance

2017-03-28
2017-01-0881
A low viscosity API SN 0W-16 engine oil was developed to achieve a 0.5% improvement in fuel efficiency over the current GF-5/API SN 0W-20 oil. Oil consumption and engine wear are the main roadblocks to the development of low viscosity engine oils. However, optimization of the base oil and additives successfully prevent oil consumption and wear. First, it was confirmed in engine tests that NOACK volatility is still an effective indicator of oil consumption even for a low viscosity grade like 0W-16. As a result of base oil volatility control, the newly developed oil achieves the same level of oil consumption as the current GF-5/API SN 0W-20 oil. Second, it was found that the base oil viscosity and molybdenum dithiocarbamate (MoDTC) had a significant effect on chain wear in rig testing that simulated silent chain wear. For the same base oil viscosity, the new oil maintains the same oil film thickness under high surface pressure.
X